Manuals / Brands / Computer Equipment / Network Hardware / Emerson / Computer Equipment / Network Hardware

Emerson RTM-ATCA-F120-OPT Table 4-1 IPMI Sensors Overview (continued)

1 68

Download 68 pages, 1.44 Mb

Functional Description

RTM-ATCA-F120-OPT Installation and Use (6806800G29C)

Present SFP07 Other FRU 0x16

Present SFP08 Other FRU 0x17

Present SFP09 Other FRU 0x18

Present SFP10 Other FRU 0x19

Present SFP11 Other FRU 0x1A

Present SFP12 Other FRU 0x1B

RTM 1.0 V Voltage 0x00

RTM 1.2 V Voltage 0x04

RTM 12 V Voltage 0x01

RTM 2.5 V Voltage 0x03

RTM 3.3 V Voltage 0x02

RTM-F120-OPT MMC Emerson IPMC Status 0xA0

RTM FPGA Vers. Emerson Firmware Revision 0x87

RTM Rptr Temp Temperature 0xA3

Temp. SFP01 Temperature 0x40

Temp. SFP02 Temperature 0x41

Temp. SFP03 Temperature 0x42

Temp. SFP04 Temperature 0x43

Temp. SFP05 Temperature 0x44

Temp. SFP06 Temperature 0x45

Temp. SFP07 Temperature 0x46

Temp. SFP08 Temperature 0x47

Temp. SFP09 Temperature 0x48

Temp. SFP10 Temperature 0x49

Temp. SFP11 Temperature 0x4A

Temp. SFP12 Temperature 0x4B

Top Edg e Tem p Temper atu re 0xA1

Table 4-1 IPMI Sensors Overview (continued)

Sensor Name Sensor Type Sensor Number

Contents

Main Trademarks Notice Limited and Restricted Rights Legend Contact Address Contents Page List of Tables Page List of Figures Page About this Manual Overview of Contents Abbreviations Conventions The following table describes the conventions used throughout this manual. Summary of Changes This manual has been revised and replaces all prior editions. Page Safety Notes Electrical Interference Safety Notes Operation Installation Safety Notes SFP/SFP+ Modules Environment Sicherheitshinweise EMV Operation Installation SFP/SFP+ Modules Umweltschutz Chapter 1 Introduction 1.1 Features Page Introduction 1.2 Standard Compliances For Declaration of Conformity refer, RTM Declaration of Conformity.. This RTM-ATCA-F120-OPT meets the following standards. Table 1-1 Standard Compliances Page Chapter 2 Hardware Preparation and Installation 2.1 Overview 2.2 Unpacking and Inspecting the RTM 2.3 Environmental and Power Requirements 2.3.1 Environmental Requirements 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements 2.4 Installing and Removing the RTM 2.4.1 Installing the RTM Page Page Page Page 2.4.2 Removing the RTM Page 2.5 Installing and Removing SFP/ SFP+ Modules Page Page Page Page Page Controls, LEDs and Connectors 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. Table 3-1 Face Plate LEDs Page Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces Fabric Channel - 1 Gbit Ethernet uplink 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks 3.2.2.1.2 1 GBit Fabric Interface Uplinks 3.2.2.2 Base Channel Interface Connectors Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink 3.2.2.2.1 10 GBit Base Interface Uplinks 3.2.2.2.2 1 GBit Base Interface Uplinks 3.2.2.3 SFP/SFP+ Module Hot Swap 3.2.2.4 Telecom Clocking Connectors CH3 CH2 Page Figure 3-5 Location of Serial Interface Connectors Serial Interface Connector Page Functional Description 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram RTM Face Plate Zone 3 Connectors 4.3 Mezzanine Management Controller Table 4-1 IPMI Sensors Overview (continued) The following figure shows the location of the on-board temperature sensors. Table 4-1 IPMI Sensors Overview (continued) Page Page Page Appendix A A.1 Emerson Network Power - Embedded Computing Documents Page Index Page Page HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: