Emerson RTM-ATCA-F120-OPT 4.3 Mezzanine Management Controller

Functional Description

RTM-ATCA-F120-OPT Installation and Use (6806800G29C) 57

4.3 Mezzanine Management Controller

The RTM provides the a Mezzanine Management Controller (MMC) based on the Atmega128L

controller which is compliant to the IPMI v1.5 standard. The MMC is connected to the front

blade's IPMC via IPMB-L.

The MMC provides access to several RTM status sensors that are accessible via IPMI. These

sensors are listed in the following table.

Table 4-1 IPMI Sensors Overview

Sensor Name Sensor Type Sensor Number

Bottom Edge Temp Temperature 0xA2

Ejector State Button / Switch 0x7F

LOS SFP01 Other FRU 0x20

LOS SFP02 Other FRU 0x21

LOS SFP03 Other FRU 0x22

LOS SFP04 Other FRU 0x23

LOS SFP05 Other FRU 0x24

LOS SFP06 Other FRU 0x25

LOS SFP07 Other FRU 0x26

LOS SFP08 Other FRU 0x27

LOS SFP09 Other FRU 0x28

LOS SFP10 Other FRU 0x29

LOS SFP11 Other FRU 0x2A

LOS SFP12 Other FRU 0x2B

Present SFP01 Other FRU 0x10

Present SFP02 Other FRU 0x11

Present SFP03 Other FRU 0x12

Present SFP04 Other FRU 0x13

Present SFP05 Other FRU 0x14

Present SFP06 Other FRU 0x15

Contents

Main Trademarks Notice Limited and Restricted Rights Legend Contact Address Contents Page List of Tables Page List of Figures Page About this Manual Overview of Contents Abbreviations Conventions The following table describes the conventions used throughout this manual. Summary of Changes This manual has been revised and replaces all prior editions. Page Safety Notes Electrical Interference Safety Notes Operation Installation Safety Notes SFP/SFP+ Modules Environment Sicherheitshinweise EMV Operation Installation SFP/SFP+ Modules Umweltschutz Chapter 1 Introduction 1.1 Features Page Introduction 1.2 Standard Compliances For Declaration of Conformity refer, RTM Declaration of Conformity.. This RTM-ATCA-F120-OPT meets the following standards. Table 1-1 Standard Compliances Page Chapter 2 Hardware Preparation and Installation 2.1 Overview 2.2 Unpacking and Inspecting the RTM 2.3 Environmental and Power Requirements 2.3.1 Environmental Requirements 2.3.2 Power Requirements The RTM has a typical power dissipation of 22W, and a maximum power dissipation of 30W. Table 2-1 Environmental Requirements 2.4 Installing and Removing the RTM 2.4.1 Installing the RTM Page Page Page Page 2.4.2 Removing the RTM Page 2.5 Installing and Removing SFP/ SFP+ Modules Page Page Page Page Page Controls, LEDs and Connectors 3.2 LEDs and Interface Connectors The following figure shows the face plate of the RTM. Figure 3-1 Face Plate 3.2.1 LEDs The RTM provides four LEDs at its face plate. Their meaning is described in the following table. 3.2.2 Interface Connectors The RTM provides access to the following interfaces at its face plate. Table 3-1 Face Plate LEDs Page Figure 3-2 Location of Ethernet Fabric Channel Uplink Interfaces Fabric Channel - 1 Gbit Ethernet uplink 3.2.2.1.1 10 GBit Fabric Interface Channel Uplinks 3.2.2.1.2 1 GBit Fabric Interface Uplinks 3.2.2.2 Base Channel Interface Connectors Base interface- 10 GBit Ethernet uplink Base interface - 10 GBit Ethernet uplink 3.2.2.2.1 10 GBit Base Interface Uplinks 3.2.2.2.2 1 GBit Base Interface Uplinks 3.2.2.3 SFP/SFP+ Module Hot Swap 3.2.2.4 Telecom Clocking Connectors CH3 CH2 Page Figure 3-5 Location of Serial Interface Connectors Serial Interface Connector Page Functional Description 4.2 Block Diagram The following figure shows the main functional blocks of the RTM. Figure 4-1 Block Diagram RTM Face Plate Zone 3 Connectors 4.3 Mezzanine Management Controller Table 4-1 IPMI Sensors Overview (continued) The following figure shows the location of the on-board temperature sensors. Table 4-1 IPMI Sensors Overview (continued) Page Page Page Appendix A A.1 Emerson Network Power - Embedded Computing Documents Page Index Page Page HOW TO REACH LITERATURE AND TECHNICAL SUPPORT: