Emerson XDF 4.11.2 Remove the Right Panel, 4.11.3 Replace a Panel

Installation

26

4.11.2 Remove the Right Panel

To remove the right panel from the XDF:

1. Locate the four panel retainers on the outside of the right XDF panel. One retainer is in each

corner of the panel.

2. Using the factory-supplied T-handle Allen wrench, turn the panel retainers counterclockwise

90 degrees.

3. Lift the panel off the lip at the bottom of the XDF and set it in a safe location.

4.11.3 Replace a Panel

1. Set the panel on the lip at the bottom of the XDF frame.

2. Using the factory-supplied T-handle Allen wrench, turn each of the four panel retainers clockwise

90 degrees.

3. Left panel only: Using the factory-supplied T-handle Allen wrench, turn the internal security

fasteners clockwise 90 degrees.

!WARNING

Risk of electric shock. Can cause injury or death.

Disconnect all local and remote electric power before working within and/or installing

equipment.

!CAUTION

Risk of heavy panel falling off. Can cause injury and/or equipment damage.

Support the panel when removing it. Unlocking the security fasteners and removing the panel

retainers will allow unsupported panel to fall.

Contents

Main Page TABLE OF CONTENTS 5.0 PIPING CONSIDERATIONSWATER/GLYCOL MODELS ONLY . . . . . . . . . . . . . . . . . . . . . . . 27 FIGURES TABL ES IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS 1.0 GLOSSARY OF SYMBOLS 2.0 PRODUCT DESCRIPTION 2.1 Operational OverviewSelf-Contained, Air Cooled Model 2.2 Operational Overview - Water/Glycol Cooled Model Figure 3 Component location, rear of XDF Figure 4 Dimensional data, self-contained, air cooled model Figure 5 Dimensional data, water/glycol cooled model Figure 6 Dimensional data, all modelstop, bottom and cable entry cutouts Caster, 1 of 4 Stabilizing F oot, 1 of 4 3.0 XDF C 3.1 Standard ComponentsSelf-Contained, Air Cooled and Water/Glycol Cooled Models 3.1.1 Frame 3.1.2 Enclosure 3.1.3 Doors 3.1.5 Environmental Control Heat RemovalSelf-Contained, Air Cooled XDF Heat RemovalWater/Glycol Cooled XDF Figure 8 Cooling system componentswater cooled models RearFront 3.1.6 ControlLieberts iCOM Controller 3.2 Coolant SourceWater/Glycol Models 3.2.1 Closed-Loop Water System !CAUTION 3.2.2 Drycooler Loop 3.3 Optional Equipment 3.3.1 General Enclosure Options 3.3.2 Power Options MP Advanced Power Strips and Controllers Uninterruptible Power Supply 4.0 I 4.1 Inspection Packing Material 4.2 Recommended Setup Equipment 4.3 Unloading the XDF 4.3.1 Handling the Unit While It is Packaged 4.3.2 Unpack the XDF 4.3.3 Removing the XDF from Skid Four (4) Lag Bolts and Two Brackets Per Corner Figure 16 Roll XDF off the shipping skid 4.4 XDF Site Preparation 4.5 Voltage Requirements 4.5.1 Voltage Input Requirements Changing Condenser Fan Power SourceSelf-Contained, Air Cooled Units 4.5.2 Uninterruptible Power SupplyOptional 4.5.3 MP Advanced Power StripsOptional 4.6 Drycooler InstallationWater/Glycol Cooled Model 4.7 Equipment Layout 4.8 Frame and Enclosure Configurations 4.8.1 Internal Mounting Rails 4.8.2 Rear-Mount RailsPosition 4.9 Mounting Hardware 4.10 DoorRemove 4.10.1 Remove the Door 4.10.2 Quick Door Removal 4.11 Side PanelsRemove and Replace 4.11.1 Remove the Left Panel 4.11.2 Remove the Right Panel 4.11.3 Replace a Panel 5.0 PIPING CONSIDERATIONSWATER/GLYCOL MODELS ONLY 5.1 General 5.2 Closed Loop Water System 5.2.1 Expansion Tanks, Fluid Relief Valves and Other Devices 5.2.2 Corrosion Protection 5.2.3 Freeze ProtectionCoolant Type and Insulation 5.3 Drycooler Loop System 5.3.1 Glycol Solutions 6.0 FILLING THE XDF WITH COOLANTWATER OR GLYCOL 6.1 Preparing the System for Filling 6.1.1 XDF Water/Glycol Cooled Unit Volume 6.1.2 Filling the System with Water or Glycol 7.0 ELECTRICAL CONNECTIONS Electrical Connections 32 Figure 22 Customer electrical connections and cable entry pointswater/glycol cooled units Move plate to back panel for alternate power cord routing (see also Figure 23) Customer Cable Entry Points 7.1 Utility Power Supply 7.1.1 Route Input Power Cables Through the XDFs Top 8.0 CABLE MANAGEMENT OPTIONS 8.1 Cable Management Considerations 8.2 Cable Management 8.3 Cable Access 8.3.1 Top Cover and Back 8.4 Optional Cable Management Channel Figure 26 Cable management mounting locations and options: Velcro cable straps, Cable Spools Figure 27 Cable management accessories: Cable Tray Cable Tray Detail View 9.0 S 9.1 XDF Startup Inspection Checklist 9.1.1 Site Conditions 9.2 Starting the XDF ESC ? 10.0 O 10.1 Environmental Control Remote CommunicationsBuilding Management Systems, Liebert SiteScan 10.2 iCOM Components and Functions Table 7 Keyboard icons and functions ? ESC 10.3 Navigating Through the iCOM Display OK NO Figure 31 iCOM simple display default screen components UNIT 1 UNIT ON T ACT 11/07130% 100% 11/07 USER MENUS 1/ 6 PASSWORD LEVE L0 ???? SETPOINTS DISPLAY SETUP U404 TEMP F / C F U405 CONTRAST 50% U406 BUZ FREQ 50% 10.4 Changing Operational Settings Table 8 User menu icons C / F % RH SET 1 2 39 6 SET 1234h 1 2 39 6 10.5 Changing iCOMs Display Settings DISPLAY SETUP U404 TEMP F / C F U405 CONTRAST 50% U406 BUZ FREQ 50% 10.7 Operation With the Door Open NO OK 10.8 Backup Ventilation System 10.9 XDF Compressor 10.10 Uninterruptible Power Supply 11.0 M 11.1 Periodic Maintenance Table 9 Troubleshooting 12.0 S Figure 36 XDF model numbers Table 10 Physical specifications XDFS141010 Table 11 Electrical specifications Table 12 Total heat rejection 12.1 Optional Power Systems Table 13 UPS performance data 12.2 Optional Managed Power - Advanced Power Strips, Vertical- or Horizontal-Mount Page Ensuring The High Availability 0f Mission-Critical Data And Applications. Technical Support / Service Locations