Important Safety Instructions | Emerson XDF specification

IMPORTANT SAFETY INSTRUCTIONS

SAVE THESE INSTRUCTIONS

This manual contains important instructions that must be closely followed during installation and maintenance of this unit to maintain compliance with agency listings. Read all safety and operating instructions before attempting to operate the XDF. Adhere to all warnings on the unit and in this manual. Follow all operating and user instructions.

This product is designed for commercial / industrial use only. This product is not intended for use with life support or other U.S. FDA designated “critical” devices. Maximum loads must not exceed those shown on the Liebert XDF serial tag.

Operate this product in an indoor environment at an ambient temperature between 35°F and 104°F (1.6°C to 40°C). Install in a clean environment, free from moisture, flammable liquids, gases and cor- rosive substances.

This product must be connected to and powered by suitable AC supplies, rated in accordance with the unit’s serial tag. It must be suitably grounded and protected by circuit breakers or fuses.

Power extension cables, if used, must be rated for the load and must not exceed 20 ft. (6.1m) in length. Liebert recommends using shielded cables for all external communication interfaces.

Ensure that the XDF has proper ventilation. Never block or insert objects into the ventilation holes or other openings. Maintain a minimum clearance of 36 in. (915mm) in front, behind, on the right side and above the self-contained, air cooled XDF for proper airflow and service. The water/glycol cooled XDF requires 36 in. (915mm) clearance in front, behind and on the right side. It does not require top clearance.

1

Image 7

Emerson XDF user manual Important Safety Instructions

Contents

Liebert XDF Page Table of Contents Cable Management Options Piping CONSIDERATIONS-WATER/GLYCOLMODELS onlyFilling the XDF with COOLANT-WATER or Glycol Electrical Connections Specifications Maintenance Tables Important Safety Instructions Indicates ground connection Glossary of SymbolsIndicates weight Hazardous Voltage Present Entry Point Condenser Air ICOM Controller Backup Ventilation Air Intake CompressorCondenser Coil 1 Brazed Plate Condenser behind grille ICOM Controller Operational Overview Water/Glycol Cooled Model Return Line Female Condenser fanRemovable to reduce Height temporarily Dimensional data, self-contained, air cooled model Plate Connection 139.7mm176.5mm 47.6mm Cable Entry Cutout 114mmEntry Cutouts Doors XDF ComponentsFrame Enclosure Heat Removal-Self-Contained, Air Cooled XDF Environmental ControlHeat Removal-Water/Glycol Cooled XDF Rear FrontBrazed Plate Condenser Liebert iCOM controller Control-Liebert’s iCOM Controller Closed-Loop Water System Coolant Source-Water/Glycol Models Water/Glycol Return Line Cooled Drycooler Loop General Enclosure Options Power Options MP Advanced Power Strips and ControllersUninterruptible Power Supply Optional Equipment Unloading the XDF Recommended Setup EquipmentInstallation Inspection Unpack the XDF Handling the Unit While It is PackagedFork Lift Right front corner detail controls side of XDF Removing the XDF from Skid Roll XDF off the shipping skid 36 915mm XDF Site Preparation915mm Voltage Input Requirements Voltage Requirements Model Feet m 60Hz 50Hz Drycooler Installation-Water/Glycol Cooled ModelOptional condensate pump performance Maximum Head Recommended equipment arrangement Equipment Layout Rear-Mount Rails-Position Frame and Enclosure ConfigurationsMounting Hardware Internal Mounting Rails Quick Door Removal Door-RemoveSide Panels-Remove and Replace Remove the Door Replace a Panel Remove the Right Panel Water supply flow rates GeneralClosed Loop Water System Piping CONSIDERATIONS-WATER/GLYCOL Models only Corrosion Protection Expansion Tanks, Fluid Relief Valves and Other DevicesFreeze Protection-Coolant Type and Insulation Glycol supply flow rates Glycol SolutionsDrycooler Loop System Ethylene glycol concentrations Filling the XDF with COOLANT-WATER or Glycol XDF Water/Glycol Cooled Unit VolumeVolume in standard Type L copper piping Preparing the System for Filling Customer Cable Entry Points Electrical ConnectionsDashed line delineates equipment compartment Rear Route Input Power Cables Through the XDF’s Top Utility Power Supply Cable Management Cable Management ConsiderationsCable Management Options Optional Cable Management Channel Cable AccessTop Cover and Back Cable Tray Detail View Startup XDF Startup Inspection ChecklistSite Conditions Escape Key Down Arrow Key Starting the XDF ICOM Components and Functions Environmental ControlOperation Icon Key Name Function Keyboard icons and functions OK no Navigating Through the iCOM Display Entering the Password Accessing Menus and Settings Viewing Data Changing Operational Settings Icon Name Description User menu icons Changing the XDF’s Default Operating Temperature Changing iCOM’s Display SettingsHighlight the setting to be changed by pressing Enter Operation With the Door Open Uninterruptible Power Supply Backup Ventilation SystemXDF Compressor Maintenance Periodic MaintenanceTroubleshooting Monitoring SpecificationsPhysical specifications Self- Contained Water/Glycol Dimensions Air Cooled XDF Total heat rejection Electrical specificationsSelf- Contained Water/Glycol Electrical Data Air Cooled XDF UPS performance data Optional Power Systems Types Quan Port Remote Monitoring and Control MP Advanced Power Strip specificationsRemote Monitoring Only Page That Ne tIti Ti n