Epson Photo750 manual Asf

EPSON Stylus Photo 750 Revision A

Table 6-3. Lubrication Point

No.	Lubrication Type/Point	Remarks
	<Lubrication Amount>	• Rotate gears after applying
	• 1/4 of gear tooth for “Gear, 67.2”	grease to evenly distribute it.
		• Use a syringe to apply it.
4	• 1/3 of gear tooth for “Combination
	Gear, 16,21.6”
	• 1/3 of gear tooth for “Gear, 23.2”
	<Lubrication Point>	• Use a syringe to apply it.
	The shaft for “Gear, 16, 40.8” on
5	“Frame, Left”.
	<Lubrication Type> G-26
	<Lubrication Amount>
	Approximately 5 mm
	<Lubrication Point>	• For the right bushing, apply it
	• Bushings for “Roller, PF”:	from the paper path side, and
		wipe off any sticking out to the
	Left: Inside the bushing
		cap assembly side.
	Right: Inside the bushing(near the
6		• Rotate “Roller, PF” after
	pump assembly)
		applying grease to evenly
	<Lubrication Type> G-26
		distribute it in the bushing.
	<Lubrication Amount>
		• Use a syringe to apply it.
	Approximately 3 mm diametrically
	<Lubrication Point>	• Do not attach the grease to the
	• Both Left/Right Bushings for	paper path.
		• Use a syringe to apply it.
7	“Roller, Exit”
	<Lubrication Type> G-26
	<Lubrication Amount>
	• Evenly apply inside the bushings.
	<Lubrication Point>	• Apply that the holder slides
	• Contact points between “Holder,	only with spring force after
		applying grease.
	Pulley Driven” and “Frame, Upper”
		• Use a syringe to apply it.
8	<Lubrication Type> G-26
	<Lubrication Amount>
	• 2 mm long for each point.

Table 6-4. Lubrication Point

No.	Lubrication Type/Point	Remarks
	<Lubrication Point>	• Avoid applying grease to
	• ASF; The round hole in the right	“Roller, Assembly, LD”
	frame of ASF (to hold the roller
9	shaft)
	<Lubrication Type> G-26
	<Lubrication Amount>
	Evenly apply inside the hole.
	<Lubrication Point>	• Completely wipe off any grease
	ASF; Contact points between “Hopper”	sticking out to the inner side of
		ASF.
	and “Lever, Hopper, Release”.
10
	<Lubrication Type> G-26
	<Lubrication Amount>
	Evenly apply lubrication to the points.
	<Lubrication Point>	• Completely wipe off any grease
	The round cutout in the left frame of	sticking out to the inner side of
		ASF.
	ASF (“Gear,34” is inserted to the
11	cutout)
	<Lubrication Type> G-26
	<Lubrication Amount>
	Evenly apply inside the hole.
	<Lubrication Point>	Lubricate the oil pad only when;
		*Replacing the carriage assembly.
	Oil pad in the carriage assembly.
		*Replacing the oil pad
	<Lubrication Type> O-12
		Use a precise syringe to apply it. If
	<Lubrication Amount>
12		you accidentally apply too much oil
	0.7cc	to the oil pad, throw the pad away
	Note: This is the amount to be applied	and take a new one again.
	to a new oil pad.	Leave the oil pad for a while to wait
		until oil is evenly infiltrated, then
		install it on the carriage assembly.

Maintenance Overview 93