ABxF Command 84H Fill All, 106 | Escort LRP2000 instruction

RFID Communications

Field	Content
SN Byte 3/tag 3	03H

SN Byte 4/tag 3	00H

SN Byte 5/tag 3	00H

SN Byte 6/tag 3	01H

SN Byte 7/tag 3	04H

SN Byte 8/tag 3	E0H

Data from Address 0002H	AAH

Data from Address 0003H	21H

Data from Address 0004H	44H

Checksum	62H

Terminator	03H

6.5.12 ABxF Command 84H: Fill All

DESCRIPTION

Command 84 H fills all RFID tags-in-field or all tags in the same family, with a one-byte value over multiple contiguous addresses.

DISCUSSION

This command is commonly used to clear an RFID tag's memory. It writes a one-byte value repetitively across a specified range of tag addresses. All tags present in the antenna field with the specified family code are affected by this command. The Fill All function requires one data value byte, a start address, and a number of bytes to fill. It fills the tag with the data value byte, starting at the specified start address for the specified number of consecutive bytes. The fill length must be set to a non-zero value. The timeout value is given in 1 msec increments and can have a value of 1EH to FFFEH (65,534 ms). When the timeout is set to 0, the controller returns a syntax error.

Field	Content
Header	0202H

Packet Size	Packet length in bytes excluding the header, packet size, checksum, and terminator bytes. 0008H
	for this command

Command	84H

Family Code	Tag Family Code - 00H = all tags

Reserved	Ignored byte, set to 00H

Start Address	2-byte value for the starting tag address

Fill Length	2-byte value for the length of the fill in number of Bytes (1-48)

Timeout	2-byte value for timeout in 1 ms units (1EH - FFFEH)

Data value Byte	1 byte of fill

Checksum	Optional checksum

Terminator	03H

LRP2000 Passive Reader/Writer

106

Image 111

Escort LRP2000 manual ABxF Command 84H Fill All, 106

Contents

LRP2000 Passive Reader/Writer Escort Memory Systems Warranty Table of Contents Rfid Communications Iii Unpacking and Inspection Introduction FCC Compliance FCC Certifications Introduction CE Certification CE Statement Changes and Modifications LRP2000 Dimensions Dimensions LRP2000 Mounting Hole Locations and Dimensions LRP2000-23 Antenna Dimensions LRP2000-26 Antenna Dimensions Antenna Environment Installation1 LRP2000-26 Antenna Assembly Installing the Antenna Green Orientation Dots Location Green Dots Joining Plate Connectors Joining Plate Joining Plate and Fasteners Completed LRP2000-26 Antenna RF Connectors and Strain Relief Connectors and Wiring Internal Connectors Terminal Blocks Antenna Cabling Antenna Connectors Single Antenna System Connections Connecting Single Antenna System Dual Antenna System Connections Connecting a Dual Antenna System J8 Pin Number Interface J8 Signal Name DB9 Pin DB25 Pin Data Terminal BlocksRS232 Pinouts, J8 Terminal Block J10 COM1 RS422 Power Supply LRP2000 Wire color Connector Pin Number Power Supply WiringInput Power Pinout J10 Pin Number Signal Name Polarity Description Input Power Supply Lugs Ethernet Wiring RS232 Wiring RS422 Wiring and Termination Digital I/O Circuitry Inputs Connector Pin Signal Name Polarity Number Outputs Terminal Signal Name Polarity Number Input from Sourcing Contact Input from NPN Sensor Sourcing Output Contact Sinking Output LED Driver Master/Slave Configuration Setting Jumper 32 on the MasterJ32 J34 OFF DIP Switch Settings on the SlaveMaster DIP Switch Settings Bank Position Slave DIP Switch Settings Setting Jumper J16 on the Slave 2 COM2 Configuring the Serial InterfaceCOM1 Defaults 1 COM1 COM2 Defaults COM2 ParametersBaud Rate 1200, 2400 9600, 19200 bps Settings Digital Board DIP SwitchDip Switch Settings Download Baud Rate Interface Restore Defaults Ignored Configuring the Ethernet Module for Network CommunicationDefault IP Address Optional Ethernet Interface Menu Loading Configuration Server Properties LED Indicators Color Meaning Error and Config LEDs 4 Alternating Flashes Flashing LED SignalsError LED 4 Flashes Error and Config LEDs 4 Simultaneous Flashes Faulty Network Connection No Dhcp Response Received LRP2000 Standard PC Serial Port How to Enter the Menu Configuration Set-Up Operating Parameters Set COM1 ParametersSet COM2 Parameters Set Operating Mode Operating ModeFraming Editing Checksum? 0 Disabled 1 Enabled Length Power up in Continuous Read Mode?Delay Between Identical Decodes Start Address Restore Factory Defaults Set RF CommunicationReturn to Main Menu Downloading DSP Firmware Download New Program Exit to Operating Mode Conventions Command protocols User I/O Commands ABx Command Set ListingsSingle Tag Commands Multi-tag Commands Multi-tag Command Parameters Command Parameters Start Continuous Read Multi-tag Example Field Number Content BytesStandard ABx Protocol Single Tag Example Field Remarks ABxS Command 04H Fill TagCommand from Host Example Response from Controller ABxS Command 05H Read ABxS Command 06H Write ABxS Command 07H Read Tag Serial Number ACHE0H ABxS Command 0DH Stop/Start Continuous Read ABxS Command 08H Tag Search ANT Config BlinkCommand Response Field Remarks Behavior Description ABxS Command 14H Get Memory Status Field ContentResponse from controller ABxS Command 16H Write Family Code ABxS Command 17H Lock Family CodeDescription ABxS Command 82H SN Read All AAH FFH 6CH ABxS Command 83H Start/Stop Continuous SN Read All 1EH0BH 4BH C5HFCH Response to a successful command follows this form ABxS Command 84H Fill Tag All ABxS Command 85H Read All Termination Packet ABxS Command 86H Write All D2H ABxS Command 87H Read Tag SN All6EH 3CH ABxS Command 88H Tag Search All AAH 8BH ABxS Command 8BH Write Family Code All AAH 8CH ABxS Command 8CH Lock Family Code All AAH 8DH ABxS Command 8DH Start/Stop Continuous Read All Data response from controller Command is formatted as shown below ABxS Command 91H Memory Lock All ABxS Command 94H SN Fill 00H 01H SN byte ABxS Command 95H SN Read ABHF3H ABxS Command 96H SN Write A4H 0EH ABxS Command 10H Set OutputRemarks LSB Bit Output D Output C Output B Output a 0CH Remarks LSB Bit Input D Input C Input B Input a ABxS Command 11H Input Status Checksum Field ContentsABx Fast Protocol Packet Size ABx Fast Multi-tag Command Structure ABx Fast Single Tag Command Structure Header 0202H Command Size ABxF Command 04H Fill Tag AEH ABxF Command 05H ReadCommand from Host Field Content Response from Controller Field Content E7H ABxF Command 06H Write ABxF Command 07H Read Tag Serial Number EEHF8H ABxF Command 08H Tag Search F2HA3H ABxF Command 0DH Start/Stop Continuous Read 1DHF6H ABxF Command 14H Get Memory Status E1HF1H ABxF Command 16H Write Family Code E5HE8H ABxF Command 82H Read Data and SN All ABxF Command 17H Lock Family Code A6H 101 6FH Command from Host Response from Controller Field Content 103 ABxF Command 83H Start/Stop Continuous SN Read All 7BH 6AH 105 106 ABxF Command 84H Fill All 107 ABxF Command 85H Block Read All C8H EBH 109 ABxF Command 86H Block Write All 110 ABxF Command 87H Read Tag SN All F4H 9BH ETX ABxF Command 88H Tag Search All 113 ABxF Command 8DH Stop/Start Continuous Read All 114 ABxF Command 91H Memory Lock All 115 ABxF Command 8BH Write Family Code All F7H ABxF Command 8CH Lock Family Code All ABxF Command 94H SN Fill Response form Controller Field Content117 9DH B0H 119 ABxF Command 95H SN Block Read 120 121 ABxF Command 96H SN Block Write 4DH Output D Output C Output B Output a Byte ABxF Command 10H Set Output123 Output LSB Bit Status 124 ABxF Command 11H Input Status 125 EDHEAH ABx Ascii Protocol Response Structure ABx Ascii Protocol Command StructureCommand Packet Structure ABx Ascii Protocol Command/Response Size Example Ascii Command, Fill Tag127 Command from Host Field Ascii Hex Ascii String Value STXResponse from Controller Field Ascii Hex Ascii String Value Error Code Description ABx Error CodesMulti-tag Error Codes ABx Standard Error Codes Field Number of Ascii Contents Characters ABx Fast Error CodesABx Ascii Error Codes Field Bytes Contents 131 Multi-tag Command Error Code Environmental Mechanical SpecificationsElectrical Communication Tags AccessoriesAvailable Models Options Decimal Hex Character 134 DEL 135