Setting Jumper J16 on the Slave | Escort LRP2000 instruction

Electrical Interface

To change the switches to a slave configuration, make the changes highlighted in Table 7. Make sure power to the LRP2000 is off before changing DIP switch settings.

Table 7: Slave DIP Switch Settings

Bank	Position 1	Position 2	Position 3	Position 4	Position 5	Position 6	Position 7	Position 8
S1	OFF	OFF	OFF	OFF	OFF	OFF	OFF	OFF

S2	ON	OFF	ON	ON	OFF	OFF	OFF	ON

S3	OFF	ON	ON	ON	OFF	OFF	ON	ON

S5	ON	ON	ON	ON	ON	ON	ON	ON

NOTE: Do not make any changes to switch bank S3 and S5.

3.9.3 Setting Jumper J16 on the Slave

Jumper J16 is a three-pole jumper located under the transmitter shield.

To change the J16 jumper to the slave setting:

1.Verify that power to the LRP2000 is off.

2.Straighten the tabs retaining the transmitter shield and remove the shield. jumper J16 is located on the left side of the first compartment.

3.Move the J16 shunt from the up position (pins 1 and 2) to the down position (pins 2 and 3). See Figure 34 below.

Figure 34: Jumper J16 Position

4. Replace the transmitter shield and fold over tabs to lock the shield in place.

LRP2000 Passive Reader/Writer

36

Image 41

Escort LRP2000 manual Setting Jumper J16 on the Slave, Slave DIP Switch Settings

Contents

LRP2000 Passive Reader/Writer Escort Memory Systems Warranty Table of Contents Rfid Communications Iii Unpacking and Inspection Introduction FCC Compliance FCC Certifications Introduction CE Certification CE Statement Changes and Modifications LRP2000 Dimensions Dimensions LRP2000 Mounting Hole Locations and Dimensions LRP2000-23 Antenna Dimensions LRP2000-26 Antenna Dimensions 1 LRP2000-26 Antenna Assembly InstallationInstalling the Antenna Antenna Environment Green Orientation Dots Location Green Dots Joining Plate Connectors Joining Plate Joining Plate and Fasteners Completed LRP2000-26 Antenna RF Connectors and Strain Relief Connectors and Wiring Internal Connectors Terminal Blocks Antenna Cabling Antenna Connectors Single Antenna System Connections Connecting Single Antenna System Dual Antenna System Connections Connecting a Dual Antenna System RS232 Pinouts, J8 Terminal Block J8 Pin Number Interface J8 Signal Name DB9 Pin DB25 PinData Terminal Blocks J10 COM1 RS422 Input Power Pinout Power Supply WiringJ10 Pin Number Signal Name Polarity Description Power Supply LRP2000 Wire color Connector Pin Number Input Power Supply Lugs Ethernet Wiring RS232 Wiring RS422 Wiring and Termination Digital I/O Circuitry Inputs Connector Pin Signal Name Polarity Number Outputs Terminal Signal Name Polarity Number Input from Sourcing Contact Input from NPN Sensor Sourcing Output Contact Sinking Output LED Driver J32 J34 Master/Slave ConfigurationSetting Jumper 32 on the Master Master DIP Switch Settings DIP Switch Settings on the SlaveBank Position OFF Slave DIP Switch Settings Setting Jumper J16 on the Slave COM1 Defaults Configuring the Serial Interface1 COM1 2 COM2 Baud Rate 1200, 2400 9600, 19200 bps COM2 DefaultsCOM2 Parameters Dip Switch Settings Digital Board DIP SwitchDownload Baud Rate Interface Restore Defaults Settings Default IP Address Configuring the Ethernet Module for Network CommunicationOptional Ethernet Interface Ignored Menu Loading Configuration Server Properties LED Indicators Color Meaning Error LED 4 Flashes Flashing LED SignalsError and Config LEDs 4 Simultaneous Flashes Error and Config LEDs 4 Alternating Flashes Faulty Network Connection No Dhcp Response Received LRP2000 Standard PC Serial Port How to Enter the Menu Configuration Set COM2 Parameters Set-Up Operating ParametersSet COM1 Parameters Framing Editing Set Operating ModeOperating Mode Checksum? 0 Disabled 1 Enabled Delay Between Identical Decodes Power up in Continuous Read Mode?Start Address Length Return to Main Menu Restore Factory DefaultsSet RF Communication Downloading DSP Firmware Download New Program Exit to Operating Mode Conventions Command protocols Single Tag Commands ABx Command Set ListingsMulti-tag Commands User I/O Commands Multi-tag Command Parameters Command Parameters Start Continuous Read Standard ABx Protocol Field Number Content BytesSingle Tag Example Multi-tag Example Command from Host ABxS Command 04H Fill TagExample Field Remarks Response from Controller ABxS Command 05H Read ABxS Command 06H Write E0H ABxS Command 07H Read Tag Serial NumberACH ABxS Command 0DH Stop/Start Continuous Read ABxS Command 08H Tag Search Command Response Field Remarks Config BlinkBehavior Description ANT Response from controller ABxS Command 14H Get Memory StatusField Content Description ABxS Command 16H Write Family CodeABxS Command 17H Lock Family Code ABxS Command 82H SN Read All AAH FFH 6CH 0BH ABxS Command 83H Start/Stop Continuous SN Read All1EH FCH 4BHC5H Response to a successful command follows this form ABxS Command 84H Fill Tag All ABxS Command 85H Read All Termination Packet ABxS Command 86H Write All 6EH ABxS Command 87H Read Tag SN All3CH D2H ABxS Command 88H Tag Search All AAH 8BH ABxS Command 8BH Write Family Code All AAH 8CH ABxS Command 8CH Lock Family Code All AAH 8DH ABxS Command 8DH Start/Stop Continuous Read All Data response from controller Command is formatted as shown below ABxS Command 91H Memory Lock All ABxS Command 94H SN Fill 00H 01H SN byte F3H ABxS Command 95H SN ReadABH ABxS Command 96H SN Write A4H Remarks LSB Bit Output D Output C Output B Output a ABxS Command 10H Set Output0CH 0EH Remarks LSB Bit Input D Input C Input B Input a ABxS Command 11H Input Status ABx Fast Protocol Field ContentsPacket Size Checksum ABx Fast Multi-tag Command Structure ABx Fast Single Tag Command Structure Header 0202H Command Size ABxF Command 04H Fill Tag Command from Host Field Content ABxF Command 05H ReadResponse from Controller Field Content AEH E7H ABxF Command 06H Write F8H ABxF Command 07H Read Tag Serial NumberEEH A3H ABxF Command 08H Tag SearchF2H F6H ABxF Command 0DH Start/Stop Continuous Read1DH F1H ABxF Command 14H Get Memory StatusE1H E8H ABxF Command 16H Write Family CodeE5H ABxF Command 82H Read Data and SN All ABxF Command 17H Lock Family Code A6H 101 6FH Command from Host Response from Controller Field Content 103 ABxF Command 83H Start/Stop Continuous SN Read All 7BH 6AH 105 106 ABxF Command 84H Fill All 107 ABxF Command 85H Block Read All C8H EBH 109 ABxF Command 86H Block Write All 110 ABxF Command 87H Read Tag SN All F4H 9BH ETX ABxF Command 88H Tag Search All 113 ABxF Command 8DH Stop/Start Continuous Read All 114 ABxF Command 91H Memory Lock All 115 ABxF Command 8BH Write Family Code All F7H ABxF Command 8CH Lock Family Code All 117 ABxF Command 94H SN FillResponse form Controller Field Content 9DH B0H 119 ABxF Command 95H SN Block Read 120 121 ABxF Command 96H SN Block Write 4DH 123 ABxF Command 10H Set OutputOutput LSB Bit Status Output D Output C Output B Output a Byte 124 ABxF Command 11H Input Status EAH 125EDH Command Packet Structure ABx Ascii Protocol Command StructureABx Ascii Protocol ABx Ascii Protocol Response Structure 127 Command/Response SizeExample Ascii Command, Fill Tag Response from Controller Field Ascii Hex Ascii String Value Command from Host Field Ascii Hex Ascii String ValueSTX Multi-tag Error Codes ABx Error CodesABx Standard Error Codes Error Code Description ABx Ascii Error Codes ABx Fast Error CodesField Bytes Contents Field Number of Ascii Contents Characters 131 Multi-tag Command Error Code Electrical Mechanical SpecificationsCommunication Environmental Available Models AccessoriesOptions Tags Decimal Hex Character 134 DEL 135