EverFocus EPTZ 100 3.1.4 Ceiling pendant mount

EPTZ100_ma_en_rev03.doc 14

3.1.4 Ceiling pendant mount

Ceiling pendant mount requires the optional adaptor EPTZ 100 CLM.

1) Assemble the connector board to the bracket adapter by 3 M4 screws. Follow the red arrow marks at

board and ceiling adapter for correct position.

2) Mount the bracket adapter with the connector board to the EPTZ 100 CLM. For wiring, use the upper

hole or side outlet of the tube.

3) Mount the EPTZ 100 CLM to the ceiling.

4) Plug the dome module in the ceiling adapter. Make sure that position of the camera module connector

fits the correct position of the connector board.

5) After plug-in, turn the camera module some degrees clockwise to latch the camera module.

6) Use the hex key to fix the camera position with the locking screw.

Contents

Main EPTZ 100 Day / Night Speed Dome Camera INSTALLATION / OPERATION 1 SAFETY WARNINGS TABLE OF CONTENTS Page 2 INTRODUCTION 2.1 FEATURES 2.2 DELIVERY SCOPE 2.3 OPTIONAL ACCESSORIES 2.4 SPECIFICATIONS Page 2.5 DIMENSIONS 2.5.1 Dimensions with ceiling mount adapter 2.5.2 Dimensions with recessed ceiling mount adapter 2.5.3 Dimension EPTZ 100 with wall mount bracket EPTZ 100 WLM 2.5.4 Dimensions wall bracket EPTZ 100 WLM 2.5.5 Dimension EPTZ 100 with ceiling pendant bracket EPTZ 100 CPM 2.5.6 Dimension ceiling pendant bracket EPTZ 100 CPM 3 INSTALLATION 3.1 MECHANICAL 4 5 2 3.1.1 Ceiling mount 3 4 5 3.1.3 Wall mount 2 8 3 4 7 5 3.1.4 Ceiling pendant mount 3.2 ELECTRICAL 3.2.1 Video 3.2.2 Power 3.2.3 RS-485 3.2.3.1 RS-485 installation with EKB 500 keyboard 3.2.3.2 RS-485 installation with EverFocus DVR 3.2.4 Alarm 3.3 COMMUNICATION SETTINGS 3.3.1 Baud rate and Protocol 3.3.2 RS-485 ID (address) Page 3.3.3 RS-485 bus termination 3.4 INITIAL START 4 OSD MENU SETUP 4.1.1 Operation in Setup Menu 4.1.2 Menu Structure OSD Structure Part 1: Page 4.1.3 Main menu 4.1.4 System info 4.1.5 Display 4.1.6 Camera 4.1.6.1 Advanced setting (camera setup) Page Page Page 4.1.7 Scan Page Page Page 4.1.8 Control 4.1.9 Privacy Mask 4.1.10 Alarm 4.1.11 Initialize 5 OPERATION WITH EKB 500 KEYBOARD 5.1 EKB 500 OPERATION WITH EVERFOCUS PROTOCOL (EVF-2) 5.1.1 EPTZ 100 setup menu 5.1.2 Preset positions 5.1.3 Autopan 5.1.4 Preset tours 5.1.5 Pattern tours 5.1.6 Remote switching of EPTZ 100 output relay 5.2 EKB 500 OPERATION WITH PELCO-D/P PROTOCOL 5.2.1 EPTZ 100 setup menu 5.2.2 Preset positions 5.2.3 Autopan 5.2.4 Preset tours 5.2.5 Pattern tours 5.2.6 Remote switching of EPTZ 100 output relay 6 APPENDIX A: BASIC SETTINGS AT EKB 500 KEYBOARD 6.1 COM PORT SETTING - RS-485 INTERFACE SETTING 6.2 DEVICE SETTING > CAMERA 7 APPENDIX B: BASIC SETTINGS AT EVERFOCUS DVR 7.1 EDR / EDVR / EDSR SERIES (EXCEPT EDSR100, EDSR100H) 7.2 ECOR / PARAGON SERIES 8 APPENDIX C: TROUBLESHOOTING 8.1 GENERAL MALFUNCTION 8.2 RECOVERING COMMUNICATION SETTINGS OF CAMERA MODULE EverFocus Electronics Corp.