EverFocus EPTZ 100 3.3 COMMUNICATION SETTINGS

EPTZ100_ma_en_rev03.doc 20

3.3 COMMUNICATION SETTINGS

The setup for general RS-485 parameters - protocol type, RS-485 address and baud rate - is done by DIP

switches, located at the top of the camera module.

Correct settings are essential for communication with the dome controller.

For correct communication, all 3 parameters - protocol, baud rate and RS-485 ID- have to comply with the

PTZ controller settings.

The 120 Ohm termination (DS3) is used at the last dome in the RS-485 bus for avoiding reflections in the

RS-485 bus.

Location of DIP switches:

DS1: Protocol and baud rate

DS2: RS-485 ID (address)

DS3: 120 Ohm termination of RS-485 bus

3.3.1 Baud rate and Protocol

The baud rate setting is done by switch 1 and 2 of DS1:

The telemetry protocol setting is done by switch 3, 4 and 5 of DS1:

DS3 DS1 DS2

Contents

Main EPTZ 100 Day / Night Speed Dome Camera INSTALLATION / OPERATION 1 SAFETY WARNINGS TABLE OF CONTENTS Page 2 INTRODUCTION 2.1 FEATURES 2.2 DELIVERY SCOPE 2.3 OPTIONAL ACCESSORIES 2.4 SPECIFICATIONS Page 2.5 DIMENSIONS 2.5.1 Dimensions with ceiling mount adapter 2.5.2 Dimensions with recessed ceiling mount adapter 2.5.3 Dimension EPTZ 100 with wall mount bracket EPTZ 100 WLM 2.5.4 Dimensions wall bracket EPTZ 100 WLM 2.5.5 Dimension EPTZ 100 with ceiling pendant bracket EPTZ 100 CPM 2.5.6 Dimension ceiling pendant bracket EPTZ 100 CPM 3 INSTALLATION 3.1 MECHANICAL 4 5 2 3.1.1 Ceiling mount 3 4 5 3.1.3 Wall mount 2 8 3 4 7 5 3.1.4 Ceiling pendant mount 3.2 ELECTRICAL 3.2.1 Video 3.2.2 Power 3.2.3 RS-485 3.2.3.1 RS-485 installation with EKB 500 keyboard 3.2.3.2 RS-485 installation with EverFocus DVR 3.2.4 Alarm 3.3 COMMUNICATION SETTINGS 3.3.1 Baud rate and Protocol 3.3.2 RS-485 ID (address) Page 3.3.3 RS-485 bus termination 3.4 INITIAL START 4 OSD MENU SETUP 4.1.1 Operation in Setup Menu 4.1.2 Menu Structure OSD Structure Part 1: Page 4.1.3 Main menu 4.1.4 System info 4.1.5 Display 4.1.6 Camera 4.1.6.1 Advanced setting (camera setup) Page Page Page 4.1.7 Scan Page Page Page 4.1.8 Control 4.1.9 Privacy Mask 4.1.10 Alarm 4.1.11 Initialize 5 OPERATION WITH EKB 500 KEYBOARD 5.1 EKB 500 OPERATION WITH EVERFOCUS PROTOCOL (EVF-2) 5.1.1 EPTZ 100 setup menu 5.1.2 Preset positions 5.1.3 Autopan 5.1.4 Preset tours 5.1.5 Pattern tours 5.1.6 Remote switching of EPTZ 100 output relay 5.2 EKB 500 OPERATION WITH PELCO-D/P PROTOCOL 5.2.1 EPTZ 100 setup menu 5.2.2 Preset positions 5.2.3 Autopan 5.2.4 Preset tours 5.2.5 Pattern tours 5.2.6 Remote switching of EPTZ 100 output relay 6 APPENDIX A: BASIC SETTINGS AT EKB 500 KEYBOARD 6.1 COM PORT SETTING - RS-485 INTERFACE SETTING 6.2 DEVICE SETTING > CAMERA 7 APPENDIX B: BASIC SETTINGS AT EVERFOCUS DVR 7.1 EDR / EDVR / EDSR SERIES (EXCEPT EDSR100, EDSR100H) 7.2 ECOR / PARAGON SERIES 8 APPENDIX C: TROUBLESHOOTING 8.1 GENERAL MALFUNCTION 8.2 RECOVERING COMMUNICATION SETTINGS OF CAMERA MODULE EverFocus Electronics Corp.