EverFocus EPTZ 100 3.2 ELECTRICAL

EPTZ100_ma_en_rev03.doc 15

3.2 ELECTRICAL

3.2.1 Video

EPTZ 100 provides a composite 1 Vp-p video output PAL/NTSC (video system depending on ordered

version) with a BNC cable socket.

Cameras and video displaying or processing equipment (DVRs, switchers etc.) require cabling with 75

Ohm video cable, e.g. RG-59, RG-12, and suitable BNC plugs.

Due to inappropriate absorbability, 50 Ohm coax cable (e.g. RG58), antenna cable and further types of

coax cable are not suitable.

Make sure that the video input of the connected video device is terminated with 75 Ohm.

When interconnecting transmission lines (twisted pair, fibre optics, radio) to the speed dome, ensure the

accurate receiver calibration.

3.2.2 Power

EPTZ 100 is powered by 24 VAC voltage. Connector is a 5.5 mm power cable socket.

Make sure that the used power supply complies with the power requirements of the speed dome (19 W

max.). 24 VAC / 1 A power source (or higher current) is recommended.

NOTE: If the power supply is not located near the dome camera, make sure that the installation cables

have sufficient diameter, otherwise the voltage drop over the power line will cause malfunction of

the speed dome (min. 21.4 VAC at speed dome power input with active PTZ motors is required).

NOTE: Do not connect the power until all installation steps are done!

Contents

Main EPTZ 100 Day / Night Speed Dome Camera INSTALLATION / OPERATION 1 SAFETY WARNINGS TABLE OF CONTENTS Page 2 INTRODUCTION 2.1 FEATURES 2.2 DELIVERY SCOPE 2.3 OPTIONAL ACCESSORIES 2.4 SPECIFICATIONS Page 2.5 DIMENSIONS 2.5.1 Dimensions with ceiling mount adapter 2.5.2 Dimensions with recessed ceiling mount adapter 2.5.3 Dimension EPTZ 100 with wall mount bracket EPTZ 100 WLM 2.5.4 Dimensions wall bracket EPTZ 100 WLM 2.5.5 Dimension EPTZ 100 with ceiling pendant bracket EPTZ 100 CPM 2.5.6 Dimension ceiling pendant bracket EPTZ 100 CPM 3 INSTALLATION 3.1 MECHANICAL 4 5 2 3.1.1 Ceiling mount 3 4 5 3.1.3 Wall mount 2 8 3 4 7 5 3.1.4 Ceiling pendant mount 3.2 ELECTRICAL 3.2.1 Video 3.2.2 Power 3.2.3 RS-485 3.2.3.1 RS-485 installation with EKB 500 keyboard 3.2.3.2 RS-485 installation with EverFocus DVR 3.2.4 Alarm 3.3 COMMUNICATION SETTINGS 3.3.1 Baud rate and Protocol 3.3.2 RS-485 ID (address) Page 3.3.3 RS-485 bus termination 3.4 INITIAL START 4 OSD MENU SETUP 4.1.1 Operation in Setup Menu 4.1.2 Menu Structure OSD Structure Part 1: Page 4.1.3 Main menu 4.1.4 System info 4.1.5 Display 4.1.6 Camera 4.1.6.1 Advanced setting (camera setup) Page Page Page 4.1.7 Scan Page Page Page 4.1.8 Control 4.1.9 Privacy Mask 4.1.10 Alarm 4.1.11 Initialize 5 OPERATION WITH EKB 500 KEYBOARD 5.1 EKB 500 OPERATION WITH EVERFOCUS PROTOCOL (EVF-2) 5.1.1 EPTZ 100 setup menu 5.1.2 Preset positions 5.1.3 Autopan 5.1.4 Preset tours 5.1.5 Pattern tours 5.1.6 Remote switching of EPTZ 100 output relay 5.2 EKB 500 OPERATION WITH PELCO-D/P PROTOCOL 5.2.1 EPTZ 100 setup menu 5.2.2 Preset positions 5.2.3 Autopan 5.2.4 Preset tours 5.2.5 Pattern tours 5.2.6 Remote switching of EPTZ 100 output relay 6 APPENDIX A: BASIC SETTINGS AT EKB 500 KEYBOARD 6.1 COM PORT SETTING - RS-485 INTERFACE SETTING 6.2 DEVICE SETTING > CAMERA 7 APPENDIX B: BASIC SETTINGS AT EVERFOCUS DVR 7.1 EDR / EDVR / EDSR SERIES (EXCEPT EDSR100, EDSR100H) 7.2 ECOR / PARAGON SERIES 8 APPENDIX C: TROUBLESHOOTING 8.1 GENERAL MALFUNCTION 8.2 RECOVERING COMMUNICATION SETTINGS OF CAMERA MODULE EverFocus Electronics Corp.