Appendix B Basic Settings AT Everfocus DVR | EverFocus EPTZ 100

7 APPENDIX B: BASIC SETTINGS AT EVERFOCUS DVR

The following settings are required to establish RS-485 communication between DVR and speed dome:

7.1EDR / EDVR / EDSR SERIES (EXCEPT EDSR100, EDSR100H)

1.CAMERA menu: enter the correct RS-485 ID (address) at the speed dome camera channel.

2.CONTROL menu: under "RS485" :

BAUD RATE:	set value identical to camera baud rate
PARITY:	NONE
DATA BIT:	8
STOP BIT:	1
PROTOCOL:	set protocol identical to speed dome protocol

NOTE: The RS-485 ID in CONTROL menu is not related to speed dome control. This RS-485 ID is used for controlling DVR by external keyboard only.

7.2ECOR / PARAGON SERIES

1.CAMERA menu: enter the correct RS-485 ID (address) at the speed dome camera channel.

2.SYSTEM > I/O CONTROL menu:

BAUD RATE:	set value identical to camera baud rate
PARITY:	NONE
DATA BIT:	8
STOP BIT:	1
PROTOCOL:	set protocol identical to speed dome protocol

NOTE: The RS-485 ID in menu I/O CONTROL menu is not related to speed dome control. This RS-485 ID is used for controlling DVR by external keyboard only.

46	EPTZ100_ma_en_rev03.doc

Image 46

EverFocus EPTZ 100 manual Appendix B Basic Settings AT Everfocus DVR, EDR / Edvr / Edsr Series Except EDSR100, EDSR100H

Contents

Eptz Safety Warnings Weee Table of Contents Device Setting Camera Introduction FeaturesOptional Accessories Delivery Scope Camera SpecificationsAlarm Communication Power Physical / environment Dimensions with ceiling mount adapter DimensionsDimensions with recessed ceiling mount adapter Dimension Eptz 100 with wall mount bracket Eptz 100 WLM Dimensions wall bracket Eptz 100 WLM Dimension Eptz 100 with ceiling pendant bracket Eptz 100 CPM Dimension ceiling pendant bracket Eptz 100 CPM Mechanical InstallationCeiling mount Recessed ceiling mount Wall mount Ceiling pendant mount Electrical PowerVideo 3 RS-485 3.1 RS-485 installation with EKB 500 keyboard 3.2 RS-485 installation with EverFocus DVR Alarm Communication Settings Baud rate and Protocol 2 RS-485 ID address EPTZ100maenrev03.doc Initial Start OSD Menu SetupOperation in Setup Menu 3 RS-485 bus termination Menu Structure OSD Structure Part Control System info Main menuDisplay Camera Advanced setting camera setupMain Setup CAM Title White BAL Focus BacklightMotion DET Auto END Zoom POS InitLens Init Exposure Brightness Reset User PresetUart Mode RET PKT Enable Special Scan GROUP1 Speed TiltLevel GROUP2 GROUP1 Tour ScanPatrol Preview PatternRecord Delete Control Privacy Mask MASK1~4 Initialize Operation with EKB 500 Keyboard General key description EKB 500 Operation with Everfocus Protocol EVF-2 Operation outline Preset positions Eptz 100 setup menuAutopan Switch Alarm Out 1-8 on Switch Alarm Out 1-8 OFF Preset toursRemote switching of Eptz 100 output relay Pattern tours EKB 500 Operation with PELCO-D/P Protocol Group 1 Tour ALL Preset TourPatrol Tour Group 2 Tour Switch relay on F4 1 Enter Switch relay OFF CLR + F4 1 Enter Switch Alarm Out COM Port Setting RS-485 Interface Setting Appendix a Basic Settings AT EKB 500 KeyboardDevice Setting Camera Ecor / Paragon Series Appendix B Basic Settings AT Everfocus DVREDR / Edvr / Edsr Series Except EDSR100, EDSR100H System I/O Control menu Recovering Communication Settings of Camera Module General Malfunction Head Office USA Subsidiary European Subsidiary China Subsidiary Japan Subsidiary