FF 120 Flat Field Ceiling Speakers | Extron electronic 305SA

Stage 3:

Installing the FF 120

Ceiling Speakers

Stage 3 Involves Installing the Devices Shown Below.

FF120 Flat Field Ceiling Speakers

FF120 Speaker (2)

Terminal Cover

Cable Clamps (2)

Seismic Tabs (3 per side)

Anchor Rings (2)

T-rails (2)

•Where it goes: Installs in ceiling tiles at predetermined location for best acoustics. Connects to switcher.

•What it does: Receives and outputs audio signal from the PVS 305SA IP switcher.

Cabling for the Speakers

Speaker Installation:

• Speaker cable (connects ceiling speakers to the PVS 305SA IP	SPK 18, 35 ft

switcher)

PoleVault IP Systems • Installation — Stage 3 (Speakers)

29

Image 33

Extron electronic 305SA manual FF 120 Flat Field Ceiling Speakers, Cabling for the Speakers, Speaker Installation

Contents

PoleVault IP Systems Sicherheitsanweisungen Deutsch Safety Instructions Guide on the Extron website FCC Class B Notice Conventions Used in this Guide Specifications AvailabilityLetter o Variables are written in slanted form as shown here PoleVault IP System Overview PoleVault IP System Installation and Wiring Overview Typical Classroom Installation Before You Begin Planning the Installation Location of the Screen and Projector Location of MediaLink Controller and Wall Plates Included Items Inventory See rear cover for contact numbers Kits Items Not Included Installation Overview Outline of Installation Steps Stage Installing the Screen Projector Mark Screen Location Install Projector to Verify LocationMark the screen location Place the PCM 340 on the T-bar Screw the adjuster plate onto the base of the pipe Using the slots on the bracket that are Viii. Evenly balanced configurationClosest to the barrel on each arm, place Verify the Image Location Slide and lock the projector onto the adjuster plate Mark the structural ceiling for lag eye bolt installation Preliminary Safety Hardware InstallationCut the Ceiling Tile Take the measurements with the PCM 340 on the T-frame Finish Projector Drop Ceiling Mount Installation Secure the Projector Drop Ceiling Mount to the Ceiling Attach the turnbuckles at the corners of the PCMHand tighten all four turnbuckles Shock or serious injury. For safety Install the Electrical Box if requiredInstall the Raco box and plaster ring onto the PCM Install the ScreenPage PVT CV D and PVT RGB D IP Plus AV Source Input Wallplates MLC 104 IP Plus installation PVT transmitter installationMLS 104 IP Plus MediaLink Controller Cabling for the Wallplates and MediaLink Controller Install the Mud Rings Features for MLC Mud Ring InstallationInsert the PVT mud ring into the wall Signal Cable Label color Provide strain reliefPull the cables at each location Install Wall Plates Connect the MLC 104 IP Plus to the switcher Install MediaLink Controller Terminal RS-232 Cable color Pin Connect to the LAN using a CAT 5 cable TCP/IP Connections made to the MLC 104 IP Plus Speaker Installation Stage 3 Involves Installing the Devices Shown BelowFF 120 Flat Field Ceiling Speakers Cabling for the Speakers Install the Speaker on the Drop Ceiling Cut Ceiling TileMark and cut the tile Attach safety cable Wire the captive screw connector Terminate the Speaker Cable for the PVS SwitcherStereo or dual mono output using parallel speaker wiring Stereo output Dual mono output Stage 4 Involves Installing the Devices Shown Below PVS 305SA IP PoleVault SwitcherPMK 550 Pole Mount Kit Rear View Install the PMK 550 Base Plate Pull the Cables at the Switcher location Switcher and Projector Cable OverviewGather the cables, pass them down the pipe Your completed connections should look like the image below Finish installing the Pole Mount Kit Configure the Switcher MLS Switcher Configuration Program Stage 5 Involves Installing the Programs Shown Below Configurator Configure the System Global Test the System Check that an image is present, and adjust as needed Adjust the audio levels on the PVS 305SA IP Test the MLC configuration is correct Final Installation Any changes to the Edid settings as needed Using Preset ModeWhen the image is correct, re-install the wallplate Preset Switch setting Resolution Number On the rear panel, set all the DIP switches to off down Using Learn Mode Available on PVT RGB D Plus only Optional Accessory Installation VoiceLift System Installation ProcedureVoiceLift System Included parts Priority Page Sensor Kit Included Parts Optional Accessory Installation Priority Page Sensor Kit PoleVault Switchers PVS, available at Configuration program for MLSTesting and Adjustment Procedure Typical paging system with PVS 305SA IP switcher Extron Warranty Outline of Installation Steps