Extron electronic 305SA specification

Using Learn Mode (Available on PVT RGB D Plus only)

1. Disconnect any sources from the front panel and remove the wallplate
	from the wall.	IN OUT
		AUDIO
2.	On the rear panel, set all the DIP switches to off (down).	COMPUTER IN
3.	Temporarily connect the main display device (the projector) to	MONITOR OUT
	the Monitor Out port.	S G
4.	On the front panel, the learn LED is lit solid green. Press and	IR OUT
4.

release the Learn button.

5. The LED flashes red when in “learning” mode, then returns to solid green when complete.

6.Re-install the wallplate and reconnect the source device. Connect a local display device to the Monitor Out port as needed.

7.Reconnect the projector to the PoleVault switcher. Restart the source and display devices

EDID Learn

Button

EDID Learn

Status LED

PoleVault IP Systems• Installation — Stage 5 (Configuration)

43

Image 47

Extron electronic 305SA manual Using Learn Mode Available on PVT RGB D Plus only

Contents

PoleVault IP Systems Sicherheitsanweisungen Deutsch Safety Instructions Guide on the Extron website FCC Class B Notice Variables are written in slanted form as shown here Specifications AvailabilityConventions Used in this Guide Letter o PoleVault IP System Overview PoleVault IP System Installation and Wiring Overview Typical Classroom Installation Before You Begin Planning the Installation Location of the Screen and Projector Location of MediaLink Controller and Wall Plates Included Items Inventory See rear cover for contact numbers Kits Items Not Included Installation Overview Outline of Installation Steps Stage Installing the Screen Projector Place the PCM 340 on the T-bar Install Projector to Verify LocationMark Screen Location Mark the screen location Screw the adjuster plate onto the base of the pipe Closest to the barrel on each arm, place Using the slots on the bracket that areViii. Evenly balanced configuration Verify the Image Location Slide and lock the projector onto the adjuster plate Take the measurements with the PCM 340 on the T-frame Preliminary Safety Hardware InstallationMark the structural ceiling for lag eye bolt installation Cut the Ceiling Tile Finish Projector Drop Ceiling Mount Installation Hand tighten all four turnbuckles Secure the Projector Drop Ceiling Mount to the CeilingAttach the turnbuckles at the corners of the PCM Install the Screen Install the Electrical Box if requiredShock or serious injury. For safety Install the Raco box and plaster ring onto the PCMPage PVT CV D and PVT RGB D IP Plus AV Source Input Wallplates Cabling for the Wallplates and MediaLink Controller PVT transmitter installationMLC 104 IP Plus installation MLS 104 IP Plus MediaLink Controller Insert the PVT mud ring into the wall Install the Mud RingsFeatures for MLC Mud Ring Installation Pull the cables at each location Signal Cable Label colorProvide strain relief Install Wall Plates Connect the MLC 104 IP Plus to the switcher Install MediaLink Controller Terminal RS-232 Cable color Pin Connect to the LAN using a CAT 5 cable TCP/IP Connections made to the MLC 104 IP Plus Cabling for the Speakers Stage 3 Involves Installing the Devices Shown BelowSpeaker Installation FF 120 Flat Field Ceiling Speakers Mark and cut the tile Install the Speaker on the Drop CeilingCut Ceiling Tile Attach safety cable Stereo output Dual mono output Terminate the Speaker Cable for the PVS SwitcherWire the captive screw connector Stereo or dual mono output using parallel speaker wiring Rear View PVS 305SA IP PoleVault SwitcherStage 4 Involves Installing the Devices Shown Below PMK 550 Pole Mount Kit Install the PMK 550 Base Plate Gather the cables, pass them down the pipe Pull the Cables at the Switcher locationSwitcher and Projector Cable Overview Your completed connections should look like the image below Finish installing the Pole Mount Kit Configure the Switcher MLS Switcher Configuration Program Stage 5 Involves Installing the Programs Shown Below Configurator Configure the System Global Test the System Check that an image is present, and adjust as needed Adjust the audio levels on the PVS 305SA IP Test the MLC configuration is correct Final Installation Preset Switch setting Resolution Number Using Preset ModeAny changes to the Edid settings as needed When the image is correct, re-install the wallplate On the rear panel, set all the DIP switches to off down Using Learn Mode Available on PVT RGB D Plus only VoiceLift System Included parts Optional Accessory Installation VoiceLift SystemInstallation Procedure Priority Page Sensor Kit Included Parts Optional Accessory Installation Priority Page Sensor Kit Typical paging system with PVS 305SA IP switcher Configuration program for MLSPoleVault Switchers PVS, available at Testing and Adjustment Procedure Extron Warranty Outline of Installation Steps