Manuals / Fostex / Computer Equipment / Network Card

Fostex PD606 owner manual Battery setting examples, Power priority DC-IN, Active battery BATT1

Models: PD606

1 226

Download 226 pages 34.98 Kb

Page 176

Chapter 8: MENU mode/BATTERY SETUP menu

<Battery setting examples>

<Example 1>: The [DC-IN] power is normally used while a battery set to battery mount 1 is standby for backup.

Power priority: DC-IN, Active battery: BATT1

[BATT1] indicator is unlit.

BATT1 is on

standby.

[BATT1] indicator is lit.

BATT1 is active.

[BATT1] indicator is unlit.

BATT1 is on

standby.

Status information

display

DC-IN is active.

Status information

display

Pop up window

DC-IN is disconnected.

Status information

display

Pop up window

DC-IN is restored.

<Example 2>: The battery mounted on battery mount 1 is normally used while the [DC-IN] is on standby for backup.

Power priority: BATT., Active battery: BATT1

[BATT1] indicator is lit.

BATT1 is active.

[BATT1] indicator is unlit.

[BATT1] indicator is lit.

Status information

display

DC-IN is on standby.

Status information

BATT1 battery is

Pop up window

display

being replaced.

DC-IN is active.

Status information

BATT1 battery

Pop up window

display

replacement

finished.

DC-IN is on standby.

176 Location Recorder Model PD606

Image 176

Fostex PD606 owner manual Battery setting examples, Power priority DC-IN, Active battery BATT1

Contents

Model PD606 Safety Instructions Important Safety Instructions Table of contents Names and functions Basic connectionsRecording/playback Force jam to external time code Cue point setting Advanced operations101 Basic playbackMenu mode 196 171180 Specifications Introduction of this manual About replacing the lithium battery Precautions on installation Introduction Location Recorder Model PD606 Main features Main features and functions Time Code IN/OUT connectors Stereo bus output connector What is in the box? PD606 Shoulder belt Driver software CDMain features Location Recorder Model PD606 Preparation before using the PD606 Table of contentsPreparation of power supply Mounting the battery Important settings for using the battery Low battery warning settingProtector adjustment Saving the battery power Battery condition displayDismounting the battery Low battery warning setting Using DC-IN Connecting the AC adaptorImportant settings for using DC Turning on the power Power switchTurning off the power Use the Menu dial to adjust the display contrastPress the ENTER/YES key to confirm the setting Display backlight and contrastInternal clock setting While SYS Setup is highlighted, press the ENTER/YES keyUse the Menu dial to select Edit and press the ENTER/YES key Enter the desired date/time dataPreparation of a DVD-RAM disk Inserting a diskSlide the Open lever to the right Insert a disk to the drive slotInitial format of a DVD-RAM disk DriveReel No FormatPress the ENTER/YES key While Are you sure? flashes, press the ENTER/YES keyWhile Reel No S001 is highlighted, press the ENTER/YES key How to set the desired reel numberAfter formatting, press the Exit key to exit the Menu mode Replacing the internal hard disk drive Insert the optional hard disk drive to the slot Cover the slot with the panel and fix it with four screwsNames and Functions Internal monitor speaker Angle adjustment armHandle ST BUS OUT connector XLR-5-32 type/balanced USB Kybd connector Series a Receptacle/USBUSB PC connector Series B Receptacle DC in 12-24V connector XLR-4-32 type/maleAnalog Input connectors XLR-3-31 type/balanced Time Code OUT connector XLR-3-32 type/balancedTime Code in connector XLR-3-31 type/balanced Right side panelWord in termination switch WORD/VIDEO in and Word OUT connectors BNC typeDigital I/O connector D-sub 25-pin/female Angle adjustment arm 9P-REMOTE connector D-sub 9-pin/femaleOperation Power switch Shift key/indicatorAbout Non-shift mode and Shift mode Front panelQuick SET key Time / TC SET keyFile SEL / DRV, PAT key Light / Contrast keyAccess indicator HDD, DVD MENU/LINK Master dial / ENTER/YES keyLocate key Clear keyPRE REC switch JAM switchSlate TONE, OFF, MIC switch 14. / Prev and / Next keysPause key/indicator green REC key/indicator redCircle Take / False Start key Slate microphoneMixer section ST BUS Ready key for stereo tracksST BUS Master control Ready key for each trackPEAK/LINK indicator REV. indicatorLIM. indicator Ready indicatorMonitor select dial Monitor mode select switchMonitor section BATT1 indicator BATT2 indicatorMonitor control Phones jackInput SEL switches Microphone power supply switchesHPF switches Stop key/indicator greenBattery mount Rear panelOpen lever ProtectorsLCD display details Home screenTime display Ubit ABSStatus information File name/Next file name Disk remainingCurrent drive/file number Protect iconScreen examples Menu list screenEdit EDL File menu screen Other connection Input connectionOutput connection Analog audio signals mic/line Digital audio signals External time code Sync signalInput connection Analog audio input connectionTime code input connection Sync signal connectionDigital audio input connection Output connection Analog audio devicesExternal analog Device External device Digital audio devices External deviceAnalog audio output connection Digital audio output connectionTime code output connection Word clock output connectionOther connections USB keyboard connectionFunction keys USB keyboardShortcuts Control keyOther keys CTRL+ L key Acts the same as the Locate key on the panelPC connection External controller connectionHow it works CUE point entryPower connection Optional AC adaptor, etcConnection examples Connection example for recordingExternal TC generator CameraFor backup purpose VTRBasic connections Location Recorder Model PD606 Playback Recording analog audio signalsRecording digital audio signals Preparation before recording Setup for recording in quick setup modeHow to make settings in the quick setup mode 23 23.97, 24, 25, 29.97DF, 29.97ND, 30DF, 30ND Frame rate selection for LTC or external time codeSystem clock reference selection TC generator mode setting TC recording mode Clock pull up/pull down settingSampling frequency and bit length selection Free Free Run, Rec-R Rec-Run, 24H-R 24H-Run, EXT Ext RunSettings in the Menu mode Power source priority selectionRecording source setting Pre/post fader selectionDefault file name setting Maximum file size settingPartition link setting Error tone output settingMixer settings Input signal selectionHigh-pass filter setting Limiter settingAdjusting the input gain for channels 1 through About gain adjustmentLimiter function Zero-crossing control functionInput channel link Phase setting for channels 1 through Controlling signals sent to the stereo busMonitoring recording signals Monitors a solo track/input channelArming tracks safe/ready setting 44.1kHz/24Bit , 48kHz/24Bit When the DVD drive is selected When partition 2 is selected Selecting the drive for recordingRecording analog audio Starting recordingPress the Ready key to arm the desired track for recording Slide the REC keyCanceling recording False Start About overloading during recordingRecording in Pre rec mode Recording a slate tone/slate mic signal HintsRecording digital audio Selecting recording sourceSelecting the sampling frequency/bit length Selecting the system clockSelecting the TC generate mode TC recording mode Recording time codeSelecting the TC frame rate Time code starts from the internal RTC real-time clock dataSetting the time code output Automatic record start by external time codeOff ReproSet the JAM switch to on Force jam to external time codeViewing the cue point list Cue point settingSetting a cue point on the fly during audio recording Editing a cue point Editing a cue labelAdding a new cue point to the cue point list Deleting a cue pointSelecting a file from the File SEL screen Basic playbackNormal audio playback Time code playback 100Cueing playback Skip / locate functions 101Skipping by file Skipping by cue point102 Locating to the beginning ABS 0 of a fileLocating to the end REC END of a file Locating to the previous locate pointAfter entering desired time value, press the Locate key 103Locating to the desired time 104 Locating to the desired cue point105 Selecting a partition Back ground mode106 Selecting auto copy mode 107Pressing the Exit key repeatedly to exit the Menu mode 108Making auto copy Slide the REC key to start recording to the partitionDVD-RAM disk Hard disk partition 109Selecting source drive 110 Making disk copyWhile DVD is flashing, press the ENTER/YES key Rec area111 If you are sure, press the ENTER/YES keyFile copy function 112113 Making file copyWhen a recorded DVD-R or CD-R disk is set When a recorded DVD-RW or CD-RW is set114 After making audio file selection, press the ENTER/YES keyAbout mirror disk Formatting in the DDR mode115 116 Use the Menu dial to select DDR and press the ENTER/YES key117 Making dual drive recordingMacintosh OSX 118Macintosh OS 119 Connecting PC to the unitHow to unmount the PD606 from the PC Example of exporting data to a computer application 120Example of copying data to a computer hard disk 121 Click on Convert -, followed by Done indicated by an arrow122 Creating and editing ALE files Edit EDL File menu 123Creating a new ALE file About an ALE file125 While New file is highlighted, press the ENTER/YES keyAfter making necessary settings, press the Exit key You can select between On and Off the default is OffWhile Video format is highlighted, press the ENTER/YES key You can select from among 23.97, 30, 24, 29.97Adding audio file entries to an ALE file 127While ALL-TAKE.ale is highlighted, press the ENTER/YES key While New entry is highlighted, press the ENTER/YES keyHow to set Circle Take to a file After adding audio file entries, press the Exit keyViewing audio file entries Viewing and editing audio file entries129 Adding an audio file entry to an existing ALE file Deleting an audio file entryPress the Exit key twice Press the ENTER/YES key to resave the ALE fileEditing an ALE file 131Editing an ALE file name After completing editing the name, press the ENTER/YES keyRemaking an ALE file While Remake ALE is highlighted, press the ENTER/YES keySelect the desired type and press the ENTER/YES key Audio file entry list in the ALE file is not133 Deleting an ALE fileAfter Remake ALE completes, press the Exit key Press the ENTER/YES key to delete the filePage Menu mode 135Shift key Menu list screen Whole Menu listMenu name Contents 137SYS Setup menu Project name setting Set project name Press the Exit key repeatedly until you exit the Menu modeCharacters you can enter using the Menu dial Characters you can enter using the alphanumeric keysDefault file name setting Default file name DateTake ReelAny number between 001 and 999 can be entered 141After entering the scene name, press the ENTER/YES key Default track name setting Default TrkName Next event number setting Next event No 143Recording FS/bit length setting Record FS&Bit Pull up/down setting Pull up/down 145Analog Recording source setting Rec source selDigital Digital output signal format selection Digital out 147Off Does not create a diagnoses file Diagnoses file setting DiagnosesYou can select from among On and Off the default is On Peak hold time setting Peak hold 149Tone rec On/Off setting Slate tone/pop tone recording mode setting Tone rec modeTone rec time setting End pop tone setting 151Pause cancel time setting Pause time USB keyboard type setting Keyboard Sel 153Pre recording time setting Pre rec time 155 Maximum file length setting Max file lengthSelectable between 2GB and 4GB the default is 2GB Selectable between On and Off the default is Off Continuous recording function Auto part. linkEnds Continues recording on the next partitionWhen Max file length is set to 4GB 157False start mode setting False start ExamplesLimiter parameter setting Limiter parameter 159Selectable between 1 3 and 1 5 the default is 1 Selectable between -12dBFS and -6dBFS the default is -6dBFSRatio setting ST BUS OUT nominal level setting Stereo out level 161Custom settings for monitoring Monitor custom 163 Monitor speaker mute setting Speaker mute You can select between On and Off the default is On165 Error tone output setting Error toneWrite error On or Off setting Input clip On/Off setting OptionsDisk warning time setting 167Chain play mode setting Chain play Unit stops when an audio file is played back to the endBack to the end AutoPlyYou can select from among Pre or Post the default is Pre Signal unaffected by the Send Level control is recordedPre/post fader selection Disk Feed 169ROM version checking Version DC-IN warning Active battery171 Battery low voltage warning setting BATT. warning While BATT. warning is highlighted, press the ENTER/YES keyDC-IN low voltage warning setting DC-IN warning 173Power supply priority setting Power priority DC-IN and Batt the default is DC-IN175 Battery priority setting Active batteryBATT1 and BATT2 the default is BATT1 Power priority BATT., Active battery BATT1 Battery setting examplesPower priority DC-IN, Active battery BATT1 177 BATT2Battery remaining time BATT. Remain Battery status BATT. status Currently used battery is highlighted179 Age in one minute steps180 System clock selection Sync clock 181While Sync Clock is highlighted, press the ENTER/YES key VideoTC frame rate selection Frame rate 182Generator mode selection Gen mode 183184 Internal TC generator setting Set Gen TCWhen Rec Run is selected When Free Run is selected 185 Editing the time code value in Rec run modeEditing the time code value in Free run mode 186 User bit setting Set Gen UbitJamming the time code value in Free run mode 187 Editing the user bitJam mode setting JAM mode 188Used Is usedTime code output source selection Sel. TC Out 189Repro GenPress the ENTER/YES key again Default LTC start time setting Default LTC start190 LTC start time editing Edit LTC start 191Ubit setting of playback time code RepTC Ubit 192MMDDYYff DDMMYYffYou can select from among On and Off the default is Off Time code output while paused Rep pause TC193 OffAutomatic recording start by external TC Recin via ExtTC 194Unit, the unit automatically starts recording Unit, the unit does not automatically start recordingInternal TC generator power-off timer TC PWR Timer 195196 Enter the desired name Editing a file name Edit file name197 198 Line No Contents Details 199200 Editing descriptor informationAdding descriptor information Deleting descriptor information201 Viewing iXML Chunk data informationEditing iXML Chunk data information Select iXML descriptor and press the ENTER/YES keyDeleting an unnecessary audio file Delete file 202Restoring a deleted audio file Restore Del. file 203Format Mode Formatting a disk or a hard disk partition Format204 DriveVolume label setting Format mode selectionMake settings of the items 205Normal Physical format on/off setting206 207 While Execute is highlighted, press the ENTER/YES keyEditing the reel number Volume label Reel No 208Record protection On/Off setting Rec protect 209Resume function On/Off setting Resume 210Partition protection On/Off setting Part. protect 211HDD operating time display HDD Ope. Time 212Load Setup menu 213User box name entry User box selectionYou can select between Box No0 and Box No6 Specifications 215Inputs/outputs 217 Recording/playbackGeneral Physical dimensions Diagram BlockIndex 221 Declaration of EC Directive Affect of Immunity on This EquipmentFor the US Customers only Fostex America Limited Warranty Shipping Page 465333