Manuals / Fujitsu / Computer Equipment / Printer

Fujitsu DL6400Pro, DL6600Pro Enable, Disable, CR-CODE CR only, Cr & Lf, LF only, Lf & Cr

Models: DL6400Pro DL6600Pro

1 247

Download 247 pages 55.32 Kb

Page 101

Changing MENU1 and MENU2 Options

Table 8–3 MENU1 and MENU2 options (Continued)

MENU 1 or MENU2	Options	Description
item


<DC3-CDE>*5		DC1 and DC3 codes are sent from the host system.
	ENABLE	Enables DC1 and DC3 codes. Any data received
		between DC3 and the next DC1 is ignored.
	DISABLE	Disables DC1 and DC3 codes. These codes are then
		ignored.

<CR-CODE>	CR ONLY	No line feed is added to a carriage return
	CR & LF	A line feed is added to each carriage return.

<LF-CODE>*2	LF ONLY	No carriage return is added to a line feed. This is the
		default when the XL24E emulation is selected.
	LF & CR	A carriage return is added to each line feed.

8-20	User’s Manual

Image 101

Fujitsu DL6400Pro, DL6600Pro user manual Enable, Disable, CR-CODE CR only, Cr & Lf, LF only, Lf & Cr

Contents

MANUALUSER’S 24-wire dot matrix printers User’s Manual User’s Manual Manufacturers Declaration of Conformity Trademark Acknowledgment User’s Manual User’s Manual Contents 10-1 Changing Head Gap Adjustment Options12-1 11-1IN-1 Image and graphics reproduction IntroductionPackage ContentsFunctions PartsInside Or continuous forms width Lists the printer parts and functionsRecommended Check that the jam removal lever is locked Setting Up the PrinterRemoving Stopper Cushion Installing the Paper Guide Insert the platen knob and align it with the gear teeth Installing the Platen KnobPlug the power cord into an outlet Connecting the Power CordConnecting the Interface Cable User’s Manual Choosing a Cassette Installing the Ribbon CassettePreparing the Ribbon Cassette Installing the Ribbon Cassette Close the top cover of the printer Removing the Ribbon Cassette Lift the reverse guide and remove the old ribbon Replacing the SubcassettePaper tape Knob Lock tabs B Loading Continuous Forms Front Turn on the printer power switchLoading Paper Loading Continuous Forms Front Tractor pins Paper holders Tractors Continuous forms Close the front cover of the printer Lower the cut-sheet trayIndicator Forms LoadingForms Rear Cutting Loading Cut Sheets Turn on printer powerRaise the paper guide. See Installing the Paper Guide on Align the cut-sheet guide with the reference point Open the front trayCut-sheet guide Cut sheet Printing on Cut Sheets Cut sheet Continuous forms Returning to Continuous Forms Operating the Printer UsingControl Panel OnlineFront Tractor FrictionRear Tractor LockedLoad LF/FFFont LockTear OFF MenuPaper Path Online + Tear OFFAlarm PowerOnline *2 Friction *2Next Display Online *1Turning Printer Power On Off Test Printing Test Printing Test printing sample Demonstration Pattern Printing Demonstration pattern Sensor Detection User’s Manual Clearing Paper Jams Continuous Forms Front Top cover Print head Paper thickness lever Cut Sheets Cut Sheets User’s Manual Shows the size range for continuous forms Paper SpecificationsContinuous Forms Misaligned Parts do not separate orBecome misaligned easily Types of binding Single-sided zigzag spot gluing Combination of the other two30 mm Printing Area Size in mm Remarks Type Number Ream weight in g/cm Front Paste here FrontSide Labels 25.4 Ambient temperature 40COr more Formats Recommended label formats Label arrangement Preprinting PrecautionsLeave an interval of 8 mm 0.3 in or greater Unit mm Miscellaneous Overview Setup ModeChapter Organization Activating Setup Mode Initial setup mode printout Mode Using SetupUsing Setup Mode Setup mode summary Exit setup mode, saving the new font and spacing Printing a List of Options Default settings at shipment MENU1 Emulate Setting Required OptionsChanging MENU1 MENU2 Options ESC/P2 DPL24C+XL24E Letter QualityReport DraftNormal CHAR-WTimes CHAR-HNone AttribItalics CondnsdTOP-MRG USA LangugeGerman SwedishPG-DHN ELOT928LATIN-P ISO-LTNSET CHR-SETItalic GraphicDisable EnableCR-CODE CR only CR & LFEnd-of-line wrap. Causes a carriage return plus a line Rghtend WrapFeed OVR-PRTChange other MENU1 or MENU2 options as required Select MENU1 or MENU2ADJUST, or Config Default does not reset options handled by HardwareHardware ChangingBIT WORD-LGBuffer 2KBYTE2XON/XOF SPACE1DTR REV-CHLPrinter detects CD Printer ignores CDChanging Print Adjustment Options Cntfine CNT-ORGCUT-ORG CutfineCUT-ADJ FcntadjRcntadj CNT-ORG Tearoff Manual Changing Conﬁguration OptionsAuto Tearpos VisibleCutload Auto TEAR-EN SECButton LoadtimALL SetupCONT-PE TractorTearoff Manual Auto Amount Changing Head Gap Adjustment OptionsPLY PLY POS.A POS.B POS.C POS.D ManualSelect SAVE&END Resetting Default ValuesUsing Diagnostic Functions Test printing SELF-TST Hex dump printing HEX-DUMP Sample hex dump Checking vertical print alignment V-ALMNT Bars offset to the left Correct vertical printing alignment You can also exit setup mode to exit V-ALMNTFlowchart in -6 shows the setup mode for the Fujitsu Setup ModeReference Listed for IBM Proprinter XL24E and Epson ESC/P2 emulationsHardwre Adjust Config GAP-ADJ LF code AGMPerforming Online Setup Print head Ribbon cassette Correct continuous forms loading User’s Manual To troubleshoot printer problems, follow the flowchart TroubleshootingTroubleshooting Inspection Maintenance Daily Inspection and Maintenance11-2 Conﬁguration body Horizontal Face Draft Quality SpecificationsVertical ⋅ Printer Specifications Printer specifications Parallel two pins Dimensions Aptc Consumables and OptionsD86B-1138-C353 for DL6600 Pro D86B-1138-C359 for DL6600 ProUser’s Manual Command Sets Fujitsu DPL24C DC2 Condensed characters offESC T Select underline typeESC M Space Backspace Carriage return Elite 12 cpiPica 10 cpi ESC PESC LF Line feed Reverse line feedForm feed 255 ESC J n255 ESC VT n Horizontal tab executionSet right margin 0 ≤ n ≤ ESC Q n ESC ODC1 CanDC3 ESC =Select font m with source and style set by n ESC % m nBits 0 and 1 Font device selection Resident font255 0 ≤ n2 ≤ Select character spacingn/360 inch, font attributesFixed 10 cpi 12 pt Istered ESC NUL m nBits 4 and 5 Speciﬁes the quality of characters to be reg Cut-Sheet Feeder Control EAN Codabar nw-7 EANSound bell Enable paper-out sensorBEL Ignore the paper-out sensorBOLDFCE, Pica 10, Corresp Cour 10, Prstg 12, ComprsdDownld 0, Downld ESC % LETTER, REPORT, DraftSHADOW, Bold NONE, ITALICS, CondnsdESC E ESC F ESC G ESC HNO-SLSH, Slash DC1/DC3 ENABLE, DisableCR-ONLY, CR & LF LF-ONLY, LF & CRUnchanged Normal Double DC4Unchanged Normal Double Single M4 controls character width Set line spacing to 7/72 inch Space Backspace Carriage return Elite characters onSet line spacing to n/216 inch 0 ≤ n ≤ ESC 3 n ≤ t1 ≤ 255, 0 ≤ t2 ≤ 255, t3 = 0, t4 = 180 orESC B NUL ESC D NULESC Q # ESC EM R ESC EMESC EM E Underline on or off ESC n On n = 1, off n = ESC GESC n 1 n Select lineSet pica Space Backspace Carriage return Set eliteESC c n1 n2 Line feed Form feedESC D 127 ESC C n Set page length to n inches 1 ≤ n ≤ ESC C NUL n ESC O255 0 ≤ ESC t nESC % n Delete characterDEL Point ESC X m n 1 nESC * m n 1 n 2 data Print raster image graphicsESC @ Enter online setup mode ESC e Online dataUser’s Manual Parallel Interface Interface InformationACK DstbSlct Inprm This signal is used to indicate that data is This signal is set low when the printer isReady to send data to the host. During Data transfer, it is used as data bitFigure C-1 Data transmission timing Data Transmission TimingFigure C-2 Data transmission timing CTS Serial InterfaceRTS Serial Options When the printer is turned onReady ETX/ACK selectableTD RD Cable WiringFigure C-1 Cable wiring DSR-enabled control ETX/ACK Serial ProtocolsON/XOFF Basic character sets for DPL24C Plus and IBM XL24E emulation Character SetsUser’s Manual User’s Manual User’s Manual User’s Manual User’s Manual User’s Manual LITHUA1 Lithuanian LITHUA2 Lithuanian MIK User’s Manual User’s Manual User’s Manual User’s Manual User’s Manual Character Sets Ecma ECMA94 USA*2LITHUA2 MIK LATN2-TMacedon ABG ABY PG-MAC ELOT927User’s Manual Using the LCD/LED Type Control Panel Control panel components LCD screen Indicator lightsUnload ButtonsExecutes form feed Points to remember about basic menusMenus and functions Changes the font, print quality, and pitch Executes line feedExecuting a micro line feed Executing a form feed or line feedTo execute a form feed or line feed Backward. To invert the arrow, press the ↓↑ but- tonTo reset the printer Resetting the printerTearing off continuous forms To tear off continuous formsChanging print font, quality, and pitch temporarily Letter Report Draft Selecting MENU1 or MENU2 Entering setup mode Enabling or disabling lock modeExiting setup mode Selecting options Using the Setup MenusSelections are not in effect until they are saved Starting functionsExample of operations Save Exit from Setup SELF-TEST AlignmentSaving changed options Selecting options in MENU1 and MENU2Using the Save function Exit from Setup Press F1 until SELF-TEST appears under Func Printing the self-testCorrecting vertical character displacement Online Power-on Special FunctionsStop MessagesUSE Save ExitWhere xxxx is -128 to +127 Where line 001 is the top-of-formInternal test Printer is performing its Appears for 2 seconds immediatelyExit Stop GO Speed Incr Decr MICRO↑ Exit SaveOperational error messages Messages indicating user-correctable problemsLCD model Cover open Cover is open Shut the cover ErrorTable E-5 Warning errors list Table E-5 Warning errors list Buffer overflow Space for download data, or check the format Table E-6 lists nonfatal error messages alphabeticallyDownload data Or check the interface cableCour Messages indicating fatal errorsPrestg CompressFatal Index Index Platen Platen knob IN-4 IN-5 IN-6 Fujitsu Offices C147-E041-05EN