Safety Instructions for the Installer

Safety Instructions for the Installer

WARNING

Do not open the cover unless totally familiar with electrical circuits and service manual.

Improper handling can result in electrical shock.

Turn off the power at the switchboard before beginning the installation.

Fire or electrical shock can result if the power is left on.

Be sure that the power supply is compatible with the voltage rating of the equipment.

Connection of an incorrect power supply can cause fire or equipment damage. The voltage rating of the equipment appears on the label above the power connector.

Use the proper fuse.

Use of a wrong fuse can damage the equipment or cause fire.

NOTICE

Observe the following compass safe distances to prevent interference to a magnetic compass:

	Standard	Steering
	compass	compass

Display	0.80 m	0.55 m
unit	0.80 m	0.55 m
unit

Page 4

Image 4

Furuno GP32 manual Safety Instructions for the Installer

Contents

Page 00080928811 Safety Instructions Safety Instructions for the Installer Table of Contents Outline Drawings Foreword FeaturesWord to the Owner of the GP-37, GP-32 GP-37 system configuration System ConfigurationGP-32 system configuration What is WAAS? Msas Egnos Waas Equipment Lists Standard supplyOptional equipment Name Type Code No Qty Remarks How to attach and remove the hard cover Operational OverviewControls Control panel Turning On and Off Power Adjusting Brilliance and ContrastTurning on the power Turning off the power Display modes default user displays Display Modes Plotter display Highway displayPlotter display Highway display Steering display Nav data displaySteering display Nav data display Digital display default display User displaysDigital display Speedometer display How to enter alphanumeric data Menu OverviewOFF Auto Simulator menu Simulation DisplaySimulator display, auto course selected Plotter Display Overview Choosing the Display RangeShifting the Cursor Cursor state and data Shifting the Display Centering Own Ship’s PositionChanging Track Plotting Interval, Stopping Plotting OFF Erasing Track Erase menuErase Track YES Plotter Display Overview This page intentionally left blank Entering Waypoints Waypoints MarksEntering a waypoint with the cursor Entering a waypoint at own ship position Entering a waypoint from the waypoint listWPTS/MARKS List GPS POS. → Mark Entering the MOB Mark Enter a NEW WPT NameMark Saved to MOB GO to MOB ? Displaying Waypoint Name Operations on the Waypoint ListDSP RTE DSP ALL Editing waypoints Erasing Waypoints Showing nearest waypoints by distance, TTG and ETAWPTS/MARKS Nearest Name Kobe Speed for Calculating Time-to-Go, Estimated Time of Arrival Routes Creating RoutesCreating a route with the cursor Sample route Routes Creating a route from the route menu Routes Creating a route from the waypoint listWPTS/MARKS List Creating a track-based route Creating a track-based route manuallyCreating a track-based route automatically Distance Editing Routes Replacing waypoints in a routeREMOVE? INSERT? SKIP? Name Route contents Route-01 Permanently deleting a waypoint from a routeInserting a waypoint in a route Temporarily deselecting a waypoint in a route Erasing Routes Changing route comment nameErase Route 01 ? YES This page intentionally left blank Setting Destination by Cursor Setting Destination by WaypointWPT-NEAR? OFF?? ROUTE? CURSOR? SETUP? Destination Setting Route as Destination Setting User Waypoint as DestinationCanceling Destination REVERSE? Alarms Arrival Alarm, Anchor Watch AlarmArrival alarm Alarms Anchor watch alarm XTE Cross Track Error AlarmARV ANC Speed Alarm WAAS/DGPS AlarmTime Alarm WAAS/DGPS mode and alarm message Trip Alarm Odometer AlarmBuzzer Type Selection Long Constant Other Functions Calculating Range, Bearing, TTG and ETARange and bearing between two waypoints Route Waas Setup GPSWaas INT Beacon EXT Beacon Dgps setup GPS Programming Dgps user channels stations Editing Dgps user channelsStation Nearest Station User Bearing Reference Erasing all user channelsTrue Erasing individual user channels Magnetic Variation Geodetic Chart SystemUnits of Measurement Time Difference using local time, Time Format Position Display FormatFor Loran C TD For Decca TD GPS Setup GPS Setup menu description Digital data User Display SetupSpeedometer Resetting Trip and Odometer Distances Reset Trip METER? Are YOU SURE? YES no ODOMETER?Reset trip meter, odometer options Speedometer display Wiring Setting for communication software onUploading, Downloading Waypoint, Route Data Downloading/Uploading between PC and GP-37/GP-32 Uploading data from a PC Loading data from a Yeoman Waypoint data format Route data format Language Route comment data formatEnd of sentence Espanol Maintenance & Troubleshooting MaintenanceDisplaying the Message Board Messages Replacing the Battery Exchange BATTERY?Ready for Battery Change Press ANY KEY To Shut Down Replacing the Fuse Diagnostics Satellite Monitor DisplaySatellite monitor display Test START? prompt Clearing Data Language and default position, unit and time difference Language Default Position Unit Time Difference This page intentionally left blank Installation Installation of Display UnitMounting considerations Desktop and overhead mounting Installation of Antenna Unit How to assemble the connectorFlush mount S kit Flush mount S kit Type OP20-17 Code No Wiring WiringHow to fix spring in fuse holder Grounding Initial Settings Output data format, data sentencesDATA1 Current loop data DATA2 RS-232C level Setup menu Output settingDATA1, Data 2 and Nmea version options This page intentionally left blank Appendix Menu Tree Digital Display division Available data Odometer, trip , timeStart from -99 to +99 Interval 01 to 99 Geodetic Chart List North American Loran C Chains GRI Decca Chains Chain Location Code AP-6 Specifications GPS Navigator GP-32 Dgps Navigator GP-37 Power Supply CT4UWOK Feb Hatai Page Page Page GPS Navigator Dgps Navigator Index WAAS/DGPS XTE Index-2