Entering the MOB Mark, Enter a NEW WPT Name, YES no | Furuno GP32

5.The cursor is selecting “NEW?”; press the [ENT] key.

ENTER A NEW WPT NAME.

0 0 4_ _ _?

(004:DEFAULT NAME) Quit: [MENU]

Waypoint name entry window

6.Enter name (if desired) with the cursor pad and then press the [ENT] key.

NAME: 004
34° 39.836'N*		MARK
135° 12.059'E*		x
10-JAN-02		10:25D

TTG 02H00M ETA: 12:25

Exit? LOG RTE?

* Current position

Waypoint attribute edit window

7.The cursor is selecting latitude. Press the [ENT] key. Enter latitude with the cursor pad and then press the [ENT] key.

8.Press the [ENT] key, enter longitude in similar fashion as you did with latitude and then press the [ENT] key.

Note: To enter position by TDs, see paragraph 7.7.

9.To change mark shape, choose the mark currently shown and then press the [ENT]

key. Use ▲ or ▼ to choose mark desired and then press the [ENT] key.

10. To change date and time to the comment of your choice, press the [ENT] key, enter comment with the cursor pad, and then press the [ENT] key again.

11. Place the cursor on “Exit?.” Press the [ENT] key.

12. Press the [MENU] key twice to finish.

3.WAYPOINTS (MARKS)

3.2Entering the MOB Mark

The MOB mark denotes man overboard position. Only one MOB mark may be entered. Each time the MOB mark is entered the previous MOB mark and its position data are written over.

1. Press the [MARK/MOB] key on any display until the following display appears.

SAVED TO MOB.

GO TO MOB ?

ARE YOU SURE?

YES NO

MOB window

2.To set MOB position as destination, press ◄ to choose YES and then press the [ENT] key. Then, the plotter display marks MOB position as shown in the illustration below.

Note: Selecting “NO” saves the position as a waypoint.

MOB position set as destination

D2D

[ 40 mn ]

BRG:

MOB

1°

RNG:

0.06mn

34° 44.000N 135° 21.000E

Bearing and range to MOB position

Plotter display when MOB

is set as destination

15

Image 25

Furuno GP32 manual Entering the MOB Mark, Enter a NEW WPT Name, Saved to MOB GO to MOB ?, YES no

Contents

Page 00080928811 Safety Instructions Safety Instructions for the Installer Table of Contents Outline Drawings Foreword FeaturesWord to the Owner of the GP-37, GP-32 GP-37 system configuration System ConfigurationGP-32 system configuration Msas Egnos Waas What is WAAS? Standard supply Equipment ListsOptional equipment Name Type Code No Qty Remarks Operational Overview How to attach and remove the hard coverControls Control panel Adjusting Brilliance and Contrast Turning On and Off PowerTurning on the power Turning off the power Display Modes Display modes default user displays Highway display Plotter displayPlotter display Highway display Nav data display Steering displaySteering display Nav data display User displays Digital display default displayDigital display Speedometer display Menu Overview How to enter alphanumeric dataOFF Auto Simulator menu Simulation DisplaySimulator display, auto course selected Choosing the Display Range Plotter Display OverviewShifting the Cursor Cursor state and data Centering Own Ship’s Position Shifting the DisplayChanging Track Plotting Interval, Stopping Plotting OFF Erase menu Erasing TrackErase Track YES Plotter Display Overview This page intentionally left blank Entering Waypoints Waypoints MarksEntering a waypoint with the cursor Entering a waypoint from the waypoint list Entering a waypoint at own ship positionWPTS/MARKS List GPS POS. → Mark Enter a NEW WPT Name Entering the MOB MarkMark Saved to MOB GO to MOB ? Operations on the Waypoint List Displaying Waypoint NameDSP RTE DSP ALL Editing waypoints Showing nearest waypoints by distance, TTG and ETA Erasing WaypointsWPTS/MARKS Nearest Name Kobe Speed for Calculating Time-to-Go, Estimated Time of Arrival Creating Routes RoutesCreating a route with the cursor Sample route Creating a route from the route menu Routes Routes Creating a route from the waypoint listWPTS/MARKS List Creating a track-based route manually Creating a track-based routeCreating a track-based route automatically Distance Replacing waypoints in a route Editing RoutesREMOVE? INSERT? SKIP? Name Permanently deleting a waypoint from a route Route contents Route-01Inserting a waypoint in a route Temporarily deselecting a waypoint in a route Changing route comment name Erasing RoutesErase Route 01 ? YES This page intentionally left blank Setting Destination by Waypoint Setting Destination by CursorWPT-NEAR? OFF?? ROUTE? CURSOR? SETUP? Destination Setting User Waypoint as Destination Setting Route as DestinationCanceling Destination REVERSE? Arrival Alarm, Anchor Watch Alarm AlarmsArrival alarm Alarms Anchor watch alarm XTE Cross Track Error AlarmARV ANC WAAS/DGPS Alarm Speed AlarmTime Alarm WAAS/DGPS mode and alarm message Odometer Alarm Trip AlarmBuzzer Type Selection Long Constant Calculating Range, Bearing, TTG and ETA Other FunctionsRange and bearing between two waypoints Route GPS Waas SetupWaas INT Beacon EXT Beacon GPS Dgps setup Editing Dgps user channels Programming Dgps user channels stationsStation Nearest Station User Erasing all user channels Bearing ReferenceTrue Erasing individual user channels Magnetic Variation Geodetic Chart SystemUnits of Measurement Position Display Format Time Difference using local time, Time FormatFor Loran C TD For Decca TD GPS Setup menu description GPS Setup Digital data User Display SetupSpeedometer Reset Trip METER? Are YOU SURE? YES no ODOMETER? Resetting Trip and Odometer DistancesReset trip meter, odometer options Speedometer display Setting for communication software on WiringUploading, Downloading Waypoint, Route Data Downloading/Uploading between PC and GP-37/GP-32 Loading data from a Yeoman Uploading data from a PC Route data format Waypoint data format Route comment data format LanguageEnd of sentence Espanol Maintenance Maintenance & TroubleshootingDisplaying the Message Board Messages Exchange BATTERY? Replacing the BatteryReady for Battery Change Press ANY KEY To Shut Down Replacing the Fuse Satellite Monitor Display DiagnosticsSatellite monitor display Test START? prompt Clearing Data Language Default Position Unit Time Difference Language and default position, unit and time difference This page intentionally left blank Installation of Display Unit InstallationMounting considerations Desktop and overhead mounting How to assemble the connector Installation of Antenna UnitFlush mount S kit Flush mount S kit Type OP20-17 Code No Wiring WiringHow to fix spring in fuse holder Grounding Output data format, data sentences Initial SettingsDATA1 Current loop data DATA2 RS-232C level Setup menu Output settingDATA1, Data 2 and Nmea version options This page intentionally left blank Menu Tree Appendix Available data Odometer, trip , time Digital Display divisionStart from -99 to +99 Interval 01 to 99 North American Geodetic Chart List GRI Loran C Chains Chain Location Code Decca Chains AP-6 Specifications GPS Navigator GP-32 Dgps Navigator GP-37 Power Supply CT4UWOK Feb Hatai Page Page Page GPS Navigator Dgps Navigator WAAS/DGPS XTE Index Index-2