352&66&21752/&+$57, 352&66&21752/,$*5$0 | GBC 930-028

F-60+ Operation and Maintenance ManualOperation

352&(66&21752/&+$57

Product:_________________________		Process: One Pass Mount & Laminate __ Date:________________

		FRONT CONTROL SETTINGS

	Speed: 1-2 fpm (30-60 cpm)		Reverse/Forward: Forward

	Roll Pressure: Trial		Top Heater: 240 °F (115 °C)

	Cooling: Off		Bottom Heater: 32 °F (0 °C)

352&(66&21752/',$*5$0

One Pass Mount and Laminate

☞NOTE

Footswitch may be used.

Printed

Image

Leader

Board

Falcon

Board

© GBC Pro-Tech 1999 April

3-11

Image 29

GBC 930-028 manual 352&66&21752/&+$57, 352&66&21752/,$*5$0, One Pass Mount and Laminate

Contents

0DLQWHQDQFH0DQXDO 60+ Operation and Maintenance Manual 6HFWLRQ Two-Pass Mount and Laminate Hot and Cold Push either Twist pressed Safety DXWLRQin an emergencyDUQLQJ. /DEHO/RFDWLRQV Inside cabinet Decal Meaning Blank These instructions so that you can insure that your new Moved and installed60+ Laminator is properly and securely unpacked Is there ample room for the laminator? Installation Alternative Power Configurations To uncrate the laminator Tools required Fork Lift Blade Locations Setup Procedure Hex wrench Adjustable wrench To level the laminator Startup Checklist Installation Operation Roll Pressure Display Displays the per Power ON/OFF Indicator Indicates HE8S To your machine and is not recommended or Covered under our warranty Must be raised to prevent damaging the rolls When the machine is not in use, the pull rollsPull roll clutch tension adjustment 3URFHVV &RQWURO&KDUWV See process chart Heat-activated laminating using mounting board with Lay the print on the board. Using a tack iron, tackFeed the work into the nip with the leading edge tight Entering the nip evenly from side to side. For thin 3URFHGXUH3DVV 352&66&21752/,$*5$0 Identification Diagram352&66&21752/&+$57 One Pass Mounting 352&66&21752/&+$57352&66&21752/,$*5$0 352&66&21752/,$*5$0 352&66&21752/&+$57One Pass Mount and Laminate Process One Pass Mount & Laminate Date 352&66&21752/,$*5$0 352&66&21752/&+$57Encapsulation Product 3 Mil Gloss/3Mil Gloss 352&66&21752/,$*5$0 352&66&21752/&+$57Cold Overlamination Process Cold Overlamination Date 352&66&21752/,$*5$0$ 352&66&21752/&+$57$Cold Mount and Laminate First Pass Process Cold Mount & Laminate First Pass Date 352&66&21752/,$*5$0% 352&66&21752/&+$57%Cold Mount and Laminate Second Pass Product Process Cold Mount & Laminate Second Pass 352&66&21752/,$*5$0$ 352&66&21752/&+$57$Mount and Hot Overlaminate First Pass Product 352&66&21752/,$*5$0% 352&66&21752/&+$57%Mount and Hot Overlaminate Second Pass Product Process Mount & Hot Overlaminate Second Pass Operation Age Inspect the footswitch cord for dam Adjust the nip Clean the rollsGBC Pro-Tech laminators require minimal mainte Adhesive coated board To clean the cabinet and covers To clean beads of adhesive, dust and dirt from the rolls Hex wrench ¾ hex wrench $GMXVWLQJWKH1LS Hex wrench Screwdriver To adjust the chain tension 1844 202 440 or fax +44 0 1844 202 Xeulfdwlrq 2XWSXW7URXEOHVKRRWLQJ*XLGH Unauthorized customer alterations will void this Warranty This warranty specifically does not coverFaces Customer’s sole and exclusive remedy under this Warranty Part Description Quantity Specifications Process control charts Accessory pack Laminating rolls Adjusting Laminating speedsPull roll 5clutch adjustment Grease fittings Resetting the laminator 1-1,3-1 Index