352&66&21752/&+$57%, 352&66&21752/,$*5$0% | GBC 930-028

F-60+ Operation and Maintenance Manual	Operation

352&(66&21752/&+$57%

Product:___________________		Process: Mount & Hot Overlaminate (Second Pass)		Date:________________

		FRONT CONTROL SETTINGS

	Speed : 0-6 fpm (0-180 cpm)		Reverse/Forward: Forward

	Roll Pressure: Trial		Top Heater: 32-105 °F (0-40	°C)

	Cooling: Off		Bottom Heater: 32 °F (0 °C)

352&(66&21752/',$*5$0%

Mount and Hot Overlaminate (Second Pass)

☞NOTE

Use footswitch to load, then accelerate materials through rolls.

Hold

Encapsulated

Image

				Release Liner
			(Peel prior to nip)
	☞ OPTIONAL


	Board	can be	fed	Foam
	through	the	pull	Foam
	through	the	pull	Core
				Core

rolls using reverse mode.

© GBC Pro-Tech 1999 April

3-17

Image 35

GBC 930-028 manual 352&66&21752/&+$57%, 352&66&21752/,$*5$0%, Mount and Hot Overlaminate Second Pass

Contents

0DLQWHQDQFH0DQXDO 60+ Operation and Maintenance Manual 6HFWLRQ Two-Pass Mount and Laminate Hot and Cold Push either Twist pressed Safety DXWLRQin an emergencyDUQLQJ. /DEHO/RFDWLRQV Inside cabinet Decal Meaning Blank Is there ample room for the laminator? Moved and installedThese instructions so that you can insure that your new 60+ Laminator is properly and securely unpacked Installation Alternative Power Configurations To uncrate the laminator Tools required Fork Lift Blade Locations Setup Procedure Hex wrench Adjustable wrench To level the laminator Startup Checklist Installation Operation Roll Pressure Display Displays the per Power ON/OFF Indicator Indicates HE8S To your machine and is not recommended or Covered under our warranty Must be raised to prevent damaging the rolls When the machine is not in use, the pull rollsPull roll clutch tension adjustment 3URFHVV &RQWURO&KDUWV See process chart Entering the nip evenly from side to side. For thin Lay the print on the board. Using a tack iron, tackHeat-activated laminating using mounting board with Feed the work into the nip with the leading edge tight 3URFHGXUH3DVV 352&66&21752/,$*5$0 Identification Diagram352&66&21752/&+$57 One Pass Mounting 352&66&21752/&+$57352&66&21752/,$*5$0 Process One Pass Mount & Laminate Date 352&66&21752/&+$57352&66&21752/,$*5$0 One Pass Mount and Laminate Product 3 Mil Gloss/3Mil Gloss 352&66&21752/&+$57352&66&21752/,$*5$0 Encapsulation Process Cold Overlamination Date 352&66&21752/&+$57352&66&21752/,$*5$0 Cold Overlamination Process Cold Mount & Laminate First Pass Date 352&66&21752/&+$57$352&66&21752/,$*5$0$ Cold Mount and Laminate First Pass Product Process Cold Mount & Laminate Second Pass 352&66&21752/&+$57%352&66&21752/,$*5$0% Cold Mount and Laminate Second Pass Product 352&66&21752/&+$57$352&66&21752/,$*5$0$ Mount and Hot Overlaminate First Pass Product Process Mount & Hot Overlaminate Second Pass 352&66&21752/&+$57%352&66&21752/,$*5$0% Mount and Hot Overlaminate Second Pass Operation Adhesive coated board Clean the rollsAge Inspect the footswitch cord for dam Adjust the nip GBC Pro-Tech laminators require minimal mainte To clean the cabinet and covers To clean beads of adhesive, dust and dirt from the rolls Hex wrench ¾ hex wrench $GMXVWLQJWKH1LS Hex wrench Screwdriver To adjust the chain tension 1844 202 440 or fax +44 0 1844 202 Xeulfdwlrq 2XWSXW7URXEOHVKRRWLQJ*XLGH Customer’s sole and exclusive remedy under this This warranty specifically does not coverUnauthorized customer alterations will void this Warranty Faces Warranty Part Description Quantity Specifications Resetting the laminator 1-1,3-1 Accessory pack Laminating rolls Adjusting Laminating speedsProcess control charts Pull roll 5clutch adjustment Grease fittings Index