Contents
0DLQWHQDQFH0DQXDO
60+ Operation and Maintenance Manual
6HFWLRQ
Two-Pass Mount and Laminate Hot and Cold
Push either Twist pressed
Safety
DXWLRQin an emergencyDUQLQJ. /DEHO/RFDWLRQV
Inside cabinet
Decal Meaning
Blank
Moved and installed
These instructions so that you can insure that your new
60+ Laminator is properly and securely unpacked
Is there ample room for the laminator?
Installation
Alternative Power Configurations
Tools required
To uncrate the laminator
Fork Lift Blade Locations
Hex wrench Adjustable wrench
Setup Procedure
Startup Checklist
To level the laminator
Installation
Operation
Power ON/OFF Indicator Indicates
Roll Pressure Display Displays the per
HE8S
Covered under our warranty
To your machine and is not recommended or
Must be raised to prevent damaging the rolls
When the machine is not in use, the pull rolls
Pull roll clutch tension adjustment
See process chart
3URFHVV &RQWURO&KDUWV
Lay the print on the board. Using a tack iron, tack
Heat-activated laminating using mounting board with
Feed the work into the nip with the leading edge tight
Entering the nip evenly from side to side. For thin
3URFHGXUH3DVV
352&66&21752/,$*5$0
Identification Diagram
352&66&21752/&+$57
One Pass Mounting
352&66&21752/&+$57
352&66&21752/,$*5$0
352&66&21752/&+$57
352&66&21752/,$*5$0
One Pass Mount and Laminate
Process One Pass Mount & Laminate Date
352&66&21752/&+$57
352&66&21752/,$*5$0
Encapsulation
Product 3 Mil Gloss/3Mil Gloss
352&66&21752/&+$57
352&66&21752/,$*5$0
Cold Overlamination
Process Cold Overlamination Date
352&66&21752/&+$57$
352&66&21752/,$*5$0$
Cold Mount and Laminate First Pass
Process Cold Mount & Laminate First Pass Date
352&66&21752/&+$57%
352&66&21752/,$*5$0%
Cold Mount and Laminate Second Pass
Product Process Cold Mount & Laminate Second Pass
352&66&21752/&+$57$
352&66&21752/,$*5$0$
Mount and Hot Overlaminate First Pass
Product
352&66&21752/&+$57%
352&66&21752/,$*5$0%
Mount and Hot Overlaminate Second Pass
Product Process Mount & Hot Overlaminate Second Pass
Operation
Clean the rolls
Age Inspect the footswitch cord for dam Adjust the nip
GBC Pro-Tech laminators require minimal mainte
Adhesive coated board
To clean beads of adhesive, dust and dirt from the rolls
To clean the cabinet and covers
$GMXVWLQJWKH1LS
Hex wrench ¾ hex wrench
To adjust the chain tension
Hex wrench Screwdriver
Xeulfdwlrq
1844 202 440 or fax +44 0 1844 202
2XWSXW7URXEOHVKRRWLQJ*XLGH
This warranty specifically does not cover
Unauthorized customer alterations will void this Warranty
Faces
Customer’s sole and exclusive remedy under this
Warranty
Quantity
Part Description
Specifications
Accessory pack Laminating rolls Adjusting Laminating speeds
Process control charts
Pull roll 5clutch adjustment Grease fittings
Resetting the laminator 1-1,3-1
Index
WARNING
ACHTUNG
MISE EN GARDE
WARNING
ACHTUNG
MISE EN GARDE
WARNING
ACHTUNG
MISE EN GARDE