352&66&21752/&+$57$, 352&66&21752/,$*5$0$ | GBC 930-028

OperationF-60+ Operation and Maintenance Manual

352&(66&21752/&+$57$

Product: ______________________		Process: Cold Mount & Laminate (First Pass) Date: ________________

		FRONT CONTROL SETTINGS

	Speed: 0-6 fpm (180 cpm)		Reverse/Forward: Forward

	Roll Pressure: 30-60%		Top Heater: 105 °F (40 °C)

	Cooling: Off		Bottom Heater: 32 °F (0 °C)

352&(66&21752/',$*5$0$

Cold Mount and Laminate (First Pass)

Pro

Gloss

Release

Paper

Rewind

Optional

Pro

Mount

3-14	© GBC Pro-Tech 1999 April

Image 32

GBC 930-028 manual 352&66&21752/&+$57$, 352&66&21752/,$*5$0$, Cold Mount and Laminate First Pass

Contents

0DLQWHQDQFH0DQXDO 60+ Operation and Maintenance Manual 6HFWLRQ Two-Pass Mount and Laminate Hot and Cold Push either Twist pressed Safety DXWLRQin an emergencyDUQLQJ. /DEHO/RFDWLRQV Inside cabinet Decal Meaning Blank Moved and installed These instructions so that you can insure that your new60+ Laminator is properly and securely unpacked Is there ample room for the laminator? Installation Alternative Power Configurations Tools required To uncrate the laminator Fork Lift Blade Locations Hex wrench Adjustable wrench Setup Procedure Startup Checklist To level the laminator Installation Operation Power ON/OFF Indicator Indicates Roll Pressure Display Displays the per HE8S Covered under our warranty To your machine and is not recommended or Must be raised to prevent damaging the rolls When the machine is not in use, the pull rollsPull roll clutch tension adjustment See process chart 3URFHVV &RQWURO&KDUWV Lay the print on the board. Using a tack iron, tack Heat-activated laminating using mounting board withFeed the work into the nip with the leading edge tight Entering the nip evenly from side to side. For thin 3URFHGXUH3DVV 352&66&21752/,$*5$0 Identification Diagram352&66&21752/&+$57 One Pass Mounting 352&66&21752/&+$57352&66&21752/,$*5$0 352&66&21752/&+$57 352&66&21752/,$*5$0One Pass Mount and Laminate Process One Pass Mount & Laminate Date 352&66&21752/&+$57 352&66&21752/,$*5$0Encapsulation Product 3 Mil Gloss/3Mil Gloss 352&66&21752/&+$57 352&66&21752/,$*5$0Cold Overlamination Process Cold Overlamination Date 352&66&21752/&+$57$ 352&66&21752/,$*5$0$Cold Mount and Laminate First Pass Process Cold Mount & Laminate First Pass Date 352&66&21752/&+$57% 352&66&21752/,$*5$0%Cold Mount and Laminate Second Pass Product Process Cold Mount & Laminate Second Pass 352&66&21752/&+$57$ 352&66&21752/,$*5$0$Mount and Hot Overlaminate First Pass Product 352&66&21752/&+$57% 352&66&21752/,$*5$0%Mount and Hot Overlaminate Second Pass Product Process Mount & Hot Overlaminate Second Pass Operation Clean the rolls Age Inspect the footswitch cord for dam Adjust the nipGBC Pro-Tech laminators require minimal mainte Adhesive coated board To clean beads of adhesive, dust and dirt from the rolls To clean the cabinet and covers $GMXVWLQJWKH1LS Hex wrench ¾ hex wrench To adjust the chain tension Hex wrench Screwdriver Xeulfdwlrq 1844 202 440 or fax +44 0 1844 202 2XWSXW7URXEOHVKRRWLQJ*XLGH This warranty specifically does not cover Unauthorized customer alterations will void this WarrantyFaces Customer’s sole and exclusive remedy under this Warranty Quantity Part Description Specifications Accessory pack Laminating rolls Adjusting Laminating speeds Process control chartsPull roll 5clutch adjustment Grease fittings Resetting the laminator 1-1,3-1 Index