F12 Starter Type, F13 CT Turns | GE Motor Protection System, LM10

F9: Auxiliary Sense 1 / Run1-Run2 Time Delays

DEVICENET OPERATIONS

Value	CT Ratio

2	90 A sensor pack

3	75:5

4	100:5

5	120:5

6	150:5

7	200:5

8	225:5

CHAPTER 5: COMMUNICATIONS

Value

CT Ratio

10300:5

11400:5

12500:5

13600:5

14700:5

15800:5

F9: Auxiliary Sense 1 / Run1-Run2 Time Delays

Format: two bytes in format 0xHHLL, where LL is the auxiliary sense 1 time delay and HH is the Run1-Run2 time delay (Run1-Run2 time delay for revisions 1.40 and lower only)

Byte LL range: 0x00 to 0xFA (i.e. 0.0 to 25.0 seconds), where 0x00 is disabled

Byte LL multiplying factor: 0.1 (i.e. actual = byte LL in decimal ⋅ 0.1 seconds)

Byte HH range: 0x00 to 0xB4 (i.e. 0 to 180 seconds)

F10: Auxiliary Sense 2 / Run2-Run1 Time Delays

Format: two bytes in format 0xHHLL, where LL is the auxiliary sense 2 time delay and HH is the Run2-Run1 time delay (Run2-Run1 time delay for revisions 1.40 and lower only)

Byte LL range: 0x00 to 0xFA (i.e. 0.0 to 25.0 seconds), where 0x00 is disabled

Byte LL multiplying factor: 0.1 (i.e. actual = byte LL in decimal ⋅ 0.1 seconds)

Byte HH range: 0x00 to 0xB4 (i.e. 0 to 180 seconds)

F11: Auxiliary Relay Faults (16-bit bitmask)

Bitmask	Fault

---- ---- ---- ---1	Overcurrent
---- ---- ---- --1-	Reserved
---- ---- ---- -1--	Jam

---- ---- ---- 1---	Stall

---- ---- ---1 ----	Current unbalance

---- ---- --1- ----	Aux sense

---- ---- -1-- ----	Load loss

---- ---- 1--- ----	Reserved

---- ---1 ---- ----	Reserved
---- --1- ---- ----	DeviceNet

---- -1-- ---- ----	Voltage range

F12: Starter Type

Format: two bytes in format 0xHHLL, where LL is the motor type and HH is reserved Byte LL enumeration:

Value	Starter Type

0	FVNR (full voltage non-reversing)

1	FVR (full voltage reversing)

2	RV (reversing)

3	2S1W (two-speed one winding; Run-2, 4:1 ratio of Run-1)

4	2S2W (two-speed two winding; Run-2, 2:1 ratio of Run-1)

5	Custom

F13: CT Turns

Format: two bytes in format 0xHHLL, where LL is the number of CT turns and HH is reserved

5–58	LM10 MOTOR PROTECTION SYSTEM – INSTRUCTION MANUAL

Image 64

GE Motor Protection System F9 Auxiliary Sense 1 / Run1-Run2 Time Delays, F10 Auxiliary Sense 2 / Run2-Run1 Time Delays

Contents

LM10 Motor Protection System Instruction Manual GE Consumer & IndustrialMultilin 1601-0165-A6 2008 GE Multilin Incorporated. All rights reserved Table of Contents 2 INSTALLATION1 INTRODUCTION 3 INTERFACE 4 FUNCTIONALITY 5 COMMUNICATIONS6 MISCELLANEOUS APPENDIX INDEX A-17 1-IV 1.1 Description LM10 Motor Protection System Chapter 1 Introduction1.1.1 The LM10 Relay 1.2.1 Features 1.2 Overview1.2.2 Current and Voltage Inputs 1.2.3 Relay Outputs 1.2.5 Block Diagram 1.2.4 Power SupplyFIGURE 1-1 Functional Block Diagram 1.3 Features 1.3.2 LED Indicators1.3.3 Switches 1.3.1 Programming and Display Unit Changes to switch settings will not take effect until power is cycled DIP Switch PositionFIGURE 1-2 LM10 Features Baud Rate 1.4 Ordering 1.4.1 Order CodesTable 1-1 LM10 Order Codes LM10 Specifications GROUND FAULTPHASE CURRENT 1.5.1 Protection Elements POWER POWER FACTORPOWER SUPPLY 1.5.3 Control Functions CONTACT INPUT Stop, Reset, DeviceNet control0 to 120 200 to 1.5.5 CT Dimensions Ground fault CTThermal overload CT 1.5.6 Outputs Environmental Approvals/CertificationSERIAL COMMUNICATIONS 1.5.8 1-12 LM10 Motor Protection System Chapter 2 Installation 2.1 Wiring2.1.1 DeviceNet 2.1.2 RS232 Port 2.1.3 Control Terminals Table 2-1 Control Connections 2.1.5 Wiring Diagram 2.1.4 Sensor Pack Input FIGURE 2-4 LM10 Wiring Diagram CHAPTER 2 INSTALLATION 2.2 Mounting 2.2.1 LM10 Mounting FIGURE 2-6 LM10 Backplate Dimensions 2.2.2 PDU Door MountFIGURE 2-7 PDU Door-mount Dimensions LM10 Motor Protection System Chapter 3 Interface 3.1 PDU Operations3.1.1 Liquid Crystal Display 3.1.2 LEDs power factor, kW, average current, and current unbalance. Pressing the History button again advances to the next history record 3.2.3 Configuration Menu 3.2 PDU Screens and Menus3.2.1 Main Startup Screen 3.2.2 History Record and Status Screens Run 2 to Run 1 delay between forward and reverse or between speeds 3.3.1 Description 3.3 EnerVista LM10 Software3.3.2 Functional Details Table 3-1 EnerVista Hot Keys LM10 Motor Protection System Chapter 4 Functionality 4.1 Overcurrent Fault Conditions4.1.1 Descriptions FIGURE 4-1 Cold Motor Trip Curves FIGURE 4-2 Hot Motor Trip Curves CHAPTER 4 FUNCTIONALITY FIGURE 4-3 Trip Curve with Jam and Stall Enabled 4.1.2 Trip Curves ExampleFIGURE 4-4 Cool Down Times Page 4.2.1 Overview 4.2 Configuration SettingsTable 4-1 LM10 Programmable Parameters CONFIGURATION SETTINGSCHAPTER 4 FUNCTIONALITY 4.2.2 Main Menu4-30 PATH Configuration Ø ENGLISH/SPANISH PATH Configuration ØØ CTs & CPTs4.2.3 Language 4.2.4 CTs and CPTs 4.2.6 Run 1 and Run 2 Setup PATH Configuration ØØØ Starter TypePATH Configuration ØØØØ Run 1 Setup 4.2.5 Starter Type Δ = phase current - average current 4.2.8 Other Settings PATH Configuration ØØØØØ Time DelaysPATH Configuration ØØØØØØ Other Settings 4.2.7 Time Delays DevNet Fault on Reset Run HrsMaintained off Auto Restart off 4.2.9 Auxiliary Relay Faults PATH Configuration ØØØØØØØ Aux Relay Faults 4.2.10 Passcode and Login PATH Configuration ØØØØØØØØ Aux Relay Faults 4.2.12 Factory Default PATH Configuration ØØØØØØØØØ Run OperationsPATH Configuration ØØØØØØØØØØ Factory Default 4.2.11 Run Operations 4.3 Status Values 4.3.1 Main MenuRun, Fault Range This value can be reset via the Reset Run Hrs configuration setting 4.4 History Values 4.4.1 Last Trip DataRange Overcurrent, Gr. Fault, Jam, Stall CuUnbalance, LdLoss, DevNet Fault, Dev Stop, Voltage, Aux Sense Range 0.0 to 3200.0 A AUX Sense 1 Fault 4.5 Motor Start/Stop LogicMotor Status Running Motor Stop Motor RUN Commands Motor STOP CommandsRUN1 Switch Input RUN1 PDU Command 4-44 LM10 Motor Protection System Chapter 5 Communications 5.1 DeviceNet Operations5.1.1 Description 5.1.2 Poll Data Table 5-1 Poll Data Group Table 5-2 Poll Data GroupTable 5-3 Poll Data Group Table 5-4 Poll Data Group 5.1.3 Identity object 5.1.4 Message Router5.1.5 DeviceNet Object UINT = 16 bit unsigned integer Baud Rate, value 0 to 2 125, 250, and 500 kbps 5.1.6 Assembly ObjectDevice outputs see format and mapping below Assembly Object, Class Code 4, Instance see below Data Formats for Device InputsCHAPTER 5 COMMUNICATIONS Assembly Object, Class Code 4, Instance Connection Object, Class Code 5, Services 5.1.7 Connection ObjectConnection Object, Class Code 5, Attributes Connection Object, Class Code 5, Instance 2 polled input/output connection 5.1.9 Overload Object 5.1.8 ACK Handler ObjectUSINT = 8-bit unsigned integer UINT = 16-bit unsigned integer 5.1.10 Extension Object UINT = 16-bit unsigned integer Access F2 Ground Fault F7 Power Transformer5.1.11 Data Formats F1 Full Load Current 16-bit unsigned integer F11 Auxiliary Relay Faults 16-bit bitmask F9 Auxiliary Sense 1 / Run1-Run2 Time DelaysF10 Auxiliary Sense 2 / Run2-Run1 Time Delays F12 Starter Type F14 Other Settings 16-bit Bitmask F15 Poll Data Group enumeration 16-bit unsigned integerF16 Run1-Run2 and Run2-Run1 Time Delay 16-bit unsigned integer F17 Trip Class F21 Motor Status 8-bit Bitmask F22 Motor Status 16-bit bitmaskF23 16-bit Unsigned Integer F24 Status Word 16-bit bitmask F25 Input Switch Status 16-bit value use only lower byte 5.1.12 Special Application Sent by scanner CANID, MACID, 0x0E, 0x64, 0x01 5.2 Serial Port 5.2.1 Description 5-64 LM10 Motor Protection System Chapter 6 Miscellaneous Revision History6.1.1 Release Dates 6.1.2 Changes to the Manual Table 6-4 Changes to Manual Since Release A3 Change to Assembly Object, Class Code 4, Instance 101, AttributeAdd Assembly Object, Class Code 4, Instance 105 Poll Data Group Changes to Connection Object, Class Code 5, Instance 2 polled 6.2 Warranty 6.2.1 GE Multilin Warranty 6-68 WARRANTYCHAPTER 6 MISCELLANEOUS A.1 DeviceNet Overview LM10 Motor Protection System Appendix AA.1.1 Description A.1.2 Controller Area Network CAN A.1.3 DeviceNet Operations A.1.6 DeviceNet Features A.1.4 Explicit Messaging and Input/Output I/O MessagingA.1.5 Pre-defined Master/Slave Connection Set A.1.7 Maximum Cable Lengths for DeviceNet A.1.8 DeviceNet Specification Highlights Table A-1 Trunk Cable Length SpecificationTable A-2 Drop Cable Length Specification Description The Object Model Device Profiles A.2.3 Network Configuration A.2.4 Configuration ProcedureA.2 LM10 and GE Fanuc 90-30 with DeviceNet A.2.1 Overview Z Select GE LM10 under GE Multilin A.2.5 Polling Input/Output ConnectionZ Also, set the Scan Interval and Reconnect Time Page Phase A values are displayed in %I00105 223 ⋅ 0.1 amps A.2.6 COS Change of State Input/Output Connection A.2.7 Cyclic Input/Output Connection A.2.8 Explicit Messaging Monitoring Data Rung 3 has a Block Move word, 3 blocks Login Configuration Level to the LM10 FIGURE A-1 Ladder Logic for Data Monitoring Making Setting Changes FIGURE A-2 Ladder Logic for Login Configuration Login User Level to the LM10 FIGURE A-3 Ladder Logic for Setting Changes FIGURE A-4 Ladder Logic for Login User A.3.2 System Setup A.3.4 Setting Up the DeviceNet NetworkA.3 LM10 and Allen-Bradley SLC500 via DeviceNet A.3.1 Description A.3.5 Changing the Mode of Operation A.3.6 Configuring the Slave Device A.3.7 Control and Monitoring of the LM10 A.3.8 Explicit Messaging with the LM10 Relay A.3.9 Data Table Layout Table A-3 Status Codes Provided by ODVA SpecificationTable A-4 Data Table Layout Table A-5 Data to Get Trip Class A.3.10 Ladder LogicTable A-6 Data for Explicit Message Response, M1 Transferred to N20 Table A-8 Data for Explicit Message Response, M1 Transferred to N20 Table A-7 Data to Get Motor Run TimeInstance, and Attribute FIGURE A-9 Ladder Logic, Rungs 0000 to A-25 FIGURE A-10 Ladder Logic, Rungs 0006 to A-26 FIGURE A-11 Ladder Logic, Rungs 0009 to A-27 A-28 Index Page LM10 MOTOR PROTECTION SYSTEM - INSTRUCTION MANUAL INDEX LM10 MOTOR PROTECTION SYSTEM - INSTRUCTION MANUAL