Language, CTs and CPTs, PATH Configuration ØØ CTs & CPTs | GE LM10

4.2.3Language

CHAPTER 4: FUNCTIONALITY

Configuration

Passcode, Login

Run Operations

Factory default

Configuration

Run Operations

Factory default

Configuration

Factory deflt

CONFIGURATION SETTINGS

See page –37.

See page –38.

See page –38.

4.2.3Language

PATH: Configuration Ø ENGLISH/SPANISH

Configuration			Configuration
ENGLISH			ENGLISH
CTs & CPTs			SPANISH
Starter Type

Range: SPANISH, ENGLISH

This setting selects the language (either English or Spanish) to display on the PDU interface.

4.2.4CTs and CPTs

PATH: Configuration ØØ CTs & CPTs

Configuration		CTs_CPTs
CTs & CPTs		Ctrl Pwr Xformer
Starter Type
RUN 1 Setup


		CTs_CPTs
		Cur Xfr / Sensor


		CTs_CPTs
		CT Turns: 1

Range: 200:120; 240:120, 480:120, 600:120, 2400:120, 3000:120, 3300:120, 4200:120, 4800:120, 5400:120, 6000: 120, 7200:120

Range: 27 FLA SenPak, 90 FLA SenPak, 75:5, 100:5, 120:5, 150:5, 200:5, 225:5, 250:5, 300:5, 400:5, 500:5, 600:5, 700:5, 800:5

Range: 1 to 4 in steps of 1

The CT and CPT settings are described below.

•Ctrl Pwr Xformer (control power transformer (CPT)): Select a CPT ratio from the choices provided. The default CPT ratio is 240:120.

•Cur Xfr / Sensor (current transformer): Select a CT ratio from the choices provided. The first two menu choices refer to sensor packs, while the remaining options are ratios of compatible CTs that might be used with the LM10.

•CT Turns: The CT may be configured so that wires are passed through the CT multiple times to increase values. This changes the effective CT ratio. Select a value between 1 and 4 for the number of turns (passes) through the CT.

LM10 MOTOR PROTECTION SYSTEM – INSTRUCTION MANUAL

4–31

Image 37

GE LM10 instruction manual Language, CTs and CPTs, PATH Configuration Ø ENGLISH/SPANISH, PATH Configuration ØØ CTs & CPTs

Contents

GE Consumer & Industrial LM10 Motor Protection System Instruction ManualMultilin 1601-0165-A6 2008 GE Multilin Incorporated. All rights reserved 2 INSTALLATION Table of Contents1 INTRODUCTION 3 INTERFACE 5 COMMUNICATIONS 4 FUNCTIONALITY6 MISCELLANEOUS APPENDIX A-17 INDEX 1-IV 1.1 Description LM10 Motor Protection System Chapter 1 Introduction1.1.1 The LM10 Relay 1.2 Overview 1.2.1 Features1.2.2 Current and Voltage Inputs 1.2.3 Relay Outputs 1.2.5 Block Diagram 1.2.4 Power SupplyFIGURE 1-1 Functional Block Diagram 1.3.2 LED Indicators 1.3 Features1.3.3 Switches 1.3.1 Programming and Display Unit DIP Switch Position Changes to switch settings will not take effect until power is cycledFIGURE 1-2 LM10 Features Baud Rate 1.4.1 Order Codes 1.4 OrderingTable 1-1 LM10 Order Codes LM10 GROUND FAULT SpecificationsPHASE CURRENT 1.5.1 Protection Elements POWER FACTOR POWERPOWER SUPPLY 1.5.3 Control Functions Stop, Reset, DeviceNet control CONTACT INPUT0 to 120 200 to Ground fault CT 1.5.5 CT DimensionsThermal overload CT 1.5.6 Outputs Approvals/Certification EnvironmentalSERIAL COMMUNICATIONS 1.5.8 1-12 2.1 Wiring LM10 Motor Protection System Chapter 2 Installation2.1.1 DeviceNet 2.1.2 RS232 Port Table 2-1 Control Connections 2.1.3 Control Terminals 2.1.4 Sensor Pack Input 2.1.5 Wiring Diagram CHAPTER 2 INSTALLATION FIGURE 2-4 LM10 Wiring Diagram 2.2.1 LM10 Mounting 2.2 Mounting FIGURE 2-6 LM10 Backplate Dimensions 2.2.2 PDU Door MountFIGURE 2-7 PDU Door-mount Dimensions 3.1 PDU Operations LM10 Motor Protection System Chapter 3 Interface3.1.1 Liquid Crystal Display 3.1.2 LEDs power factor, kW, average current, and current unbalance. Pressing the History button again advances to the next history record 3.2 PDU Screens and Menus 3.2.3 Configuration Menu3.2.1 Main Startup Screen 3.2.2 History Record and Status Screens Run 2 to Run 1 delay between forward and reverse or between speeds 3.3.1 Description 3.3 EnerVista LM10 Software3.3.2 Functional Details Table 3-1 EnerVista Hot Keys LM10 Motor Protection System Chapter 4 Functionality 4.1 Overcurrent Fault Conditions4.1.1 Descriptions CHAPTER 4 FUNCTIONALITY FIGURE 4-1 Cold Motor Trip Curves FIGURE 4-2 Hot Motor Trip Curves FIGURE 4-3 Trip Curve with Jam and Stall Enabled 4.1.2 Trip Curves ExampleFIGURE 4-4 Cool Down Times Page 4.2.1 Overview 4.2 Configuration SettingsTable 4-1 LM10 Programmable Parameters CONFIGURATION SETTINGSCHAPTER 4 FUNCTIONALITY 4.2.2 Main Menu4-30 PATH Configuration ØØ CTs & CPTs PATH Configuration Ø ENGLISH/SPANISH4.2.3 Language 4.2.4 CTs and CPTs PATH Configuration ØØØ Starter Type 4.2.6 Run 1 and Run 2 SetupPATH Configuration ØØØØ Run 1 Setup 4.2.5 Starter Type Δ = phase current - average current PATH Configuration ØØØØØ Time Delays 4.2.8 Other SettingsPATH Configuration ØØØØØØ Other Settings 4.2.7 Time Delays Reset Run Hrs DevNet Fault onMaintained off Auto Restart off PATH Configuration ØØØØØØØ Aux Relay Faults 4.2.9 Auxiliary Relay Faults PATH Configuration ØØØØØØØØ Aux Relay Faults 4.2.10 Passcode and Login PATH Configuration ØØØØØØØØØ Run Operations 4.2.12 Factory DefaultPATH Configuration ØØØØØØØØØØ Factory Default 4.2.11 Run Operations 4.3.1 Main Menu 4.3 Status ValuesRun, Fault Range This value can be reset via the Reset Run Hrs configuration setting 4.4.1 Last Trip Data 4.4 History ValuesRange Overcurrent, Gr. Fault, Jam, Stall CuUnbalance, LdLoss, DevNet Fault, Dev Stop, Voltage, Aux Sense Range 0.0 to 3200.0 A 4.5 Motor Start/Stop Logic AUX Sense 1 FaultMotor Status Running Motor Stop Motor STOP Commands Motor RUN CommandsRUN1 Switch Input RUN1 PDU Command 4-44 5.1 DeviceNet Operations LM10 Motor Protection System Chapter 5 Communications5.1.1 Description 5.1.2 Poll Data Table 5-2 Poll Data Group Table 5-1 Poll Data GroupTable 5-3 Poll Data Group Table 5-4 Poll Data Group 5.1.4 Message Router 5.1.3 Identity object5.1.5 DeviceNet Object UINT = 16 bit unsigned integer Baud Rate, value 0 to 2 125, 250, and 500 kbps 5.1.6 Assembly ObjectDevice outputs see format and mapping below Assembly Object, Class Code 4, Instance see below Data Formats for Device InputsCHAPTER 5 COMMUNICATIONS Assembly Object, Class Code 4, Instance Connection Object, Class Code 5, Services 5.1.7 Connection ObjectConnection Object, Class Code 5, Attributes Connection Object, Class Code 5, Instance 2 polled input/output connection 5.1.9 Overload Object 5.1.8 ACK Handler ObjectUSINT = 8-bit unsigned integer UINT = 16-bit unsigned integer UINT = 16-bit unsigned integer 5.1.10 Extension Object Attribute F7 Power Transformer F2 Ground Fault5.1.11 Data Formats F1 Full Load Current 16-bit unsigned integer F9 Auxiliary Sense 1 / Run1-Run2 Time Delays F11 Auxiliary Relay Faults 16-bit bitmaskF10 Auxiliary Sense 2 / Run2-Run1 Time Delays F12 Starter Type F15 Poll Data Group enumeration 16-bit unsigned integer F14 Other Settings 16-bit BitmaskF16 Run1-Run2 and Run2-Run1 Time Delay 16-bit unsigned integer F17 Trip Class F22 Motor Status 16-bit bitmask F21 Motor Status 8-bit BitmaskF23 16-bit Unsigned Integer F24 Status Word 16-bit bitmask 5.1.12 Special Application F25 Input Switch Status 16-bit value use only lower byte Sent by scanner CANID, MACID, 0x0E, 0x64, 0x01 5.2.1 Description 5.2 Serial Port 5-64 Revision History LM10 Motor Protection System Chapter 6 Miscellaneous6.1.1 Release Dates 6.1.2 Changes to the Manual Change to Assembly Object, Class Code 4, Instance 101, Attribute Table 6-4 Changes to Manual Since Release A3Add Assembly Object, Class Code 4, Instance 105 Poll Data Group Changes to Connection Object, Class Code 5, Instance 2 polled 6.2.1 GE Multilin Warranty 6.2 Warranty 6-68 WARRANTYCHAPTER 6 MISCELLANEOUS A.1 DeviceNet Overview LM10 Motor Protection System Appendix AA.1.1 Description A.1.3 DeviceNet Operations A.1.2 Controller Area Network CAN A.1.4 Explicit Messaging and Input/Output I/O Messaging A.1.6 DeviceNet FeaturesA.1.5 Pre-defined Master/Slave Connection Set A.1.7 Maximum Cable Lengths for DeviceNet Table A-1 Trunk Cable Length Specification A.1.8 DeviceNet Specification HighlightsTable A-2 Drop Cable Length Specification Description Device Profiles The Object Model A.2.4 Configuration Procedure A.2.3 Network ConfigurationA.2 LM10 and GE Fanuc 90-30 with DeviceNet A.2.1 Overview Z Select GE LM10 under GE Multilin A.2.5 Polling Input/Output ConnectionZ Also, set the Scan Interval and Reconnect Time Page Phase A values are displayed in %I00105 223 ⋅ 0.1 amps A.2.7 Cyclic Input/Output Connection A.2.6 COS Change of State Input/Output Connection Monitoring Data A.2.8 Explicit Messaging Rung 3 has a Block Move word, 3 blocks FIGURE A-1 Ladder Logic for Data Monitoring Login Configuration Level to the LM10 FIGURE A-2 Ladder Logic for Login Configuration Making Setting Changes FIGURE A-3 Ladder Logic for Setting Changes Login User Level to the LM10 FIGURE A-4 Ladder Logic for Login User A.3.4 Setting Up the DeviceNet Network A.3.2 System SetupA.3 LM10 and Allen-Bradley SLC500 via DeviceNet A.3.1 Description A.3.5 Changing the Mode of Operation A.3.6 Configuring the Slave Device A.3.7 Control and Monitoring of the LM10 A.3.8 Explicit Messaging with the LM10 Relay A.3.9 Data Table Layout Table A-3 Status Codes Provided by ODVA SpecificationTable A-4 Data Table Layout Table A-5 Data to Get Trip Class A.3.10 Ladder LogicTable A-6 Data for Explicit Message Response, M1 Transferred to N20 Table A-8 Data for Explicit Message Response, M1 Transferred to N20 Table A-7 Data to Get Motor Run TimeInstance, and Attribute A-25 FIGURE A-9 Ladder Logic, Rungs 0000 to A-26 FIGURE A-10 Ladder Logic, Rungs 0006 to A-27 FIGURE A-11 Ladder Logic, Rungs 0009 to A-28 Index Page LM10 MOTOR PROTECTION SYSTEM - INSTRUCTION MANUAL LM10 MOTOR PROTECTION SYSTEM - INSTRUCTION MANUAL INDEX