Attribute, Access, Name/Description | GE Motor Protection System

DEVICENET OPERATIONS			CHAPTER 5: COMMUNICATIONS

	Attribute	Access	Name/Description	Data Type	Value

	0x09	Get/set	User setting, Run 2, stall	F4	Trip, Time

	0x0A	Get/set	User setting, Run 1, unbalance	F5	Trip, Time

	0x0B	Get/set	User setting, Run 2, unbalance	F5	Trip, Time

	0x0C	Get/set	User setting, Run 1, load loss	F6	Trip, Time

	0x0D	Get/set	User setting, Run 2, load loss	F6	Trip, Time

	0x0E	Get/set	User setting, power transformers	F7	0 to 11

	0x0F	Get/set	User setting, current transformers	F8	1 to 15

	0x10	Get/set	User setting, auxiliary sense 1 timer	F9	0.1 ⋅ (0 to 250)

	0x11	Get/set	User setting, auxiliary sense 2 timer	F10	0.1 ⋅ (0 to 250)

	0x12	Get/set	User setting, auxiliary relay flags	F11	16 bits

	0x15	Get	Motor run time hours	UINT	Hours

	0x1A	Get/set	Configure passcode	UINT	Code (0)

	0x24	Get/set	User setting, motor type	F12	Type 0 to 5

	0x25	Get/set	User setting, loops through CT	F13	1 to 4

	0x26	Get/set	Flags (Mrun, AutoRestart, O/V Volt	F14	16 bits
			Enable, DNFault, 50 Hz)

	0x2E	Call	Reset LM10*	N/A	---
	0x1C	Call	Reset factory default user settings	N/A	---

	0x2F	Get	Trip class	F17	---

	0x30	Get	MAC ID	F18	---

	0x31	Get	DeviceNet baud rate	F19	---

	0x34	Get	Input switch status	F25	16 bits

	0x38	Get	Remaining cool-down period	F26	16 bits

	0x39	Get/set	Poll data group	F15	1 to 4

	0x3A	Get/set	Run1-Run2 time delay	F16	0 to 600 sec.

	0x3B	Get/set	Run2-Run1 time delay2	F16	0 to 600 sec.
	0x40	History	Status (send data byte 0 for current, 1	F24	---
			to 10 for history)

	0x41	History	Phase A current	F23	⋅ 0.1 A

	0x42	History	Phase B current	F23	⋅ 0.1 A

	0x43	History	Phase C current	F23	⋅ 0.1 A

	0x44	History	Ground current	F23	⋅ 0.1 A

	0x45	History	Voltage	UINT	volts

	0x46	History	Power factor	UINT	percent

	0x47	History	Watts	F23	0.1 kW

	0x48	History	Operating current	F23	⋅ 0.1 A

	0x49	History	Current unbalance	UINT	percent

	0x50	Login	User	---	---

	0x51	Login	Configuration	UINT	Passcode

	0x52	Login	Calibration	UINT	Passcode

*This call function has the same result as pressing the Reset key on the PDU display Applies to revisions 1.50 and higher

The data type format codes for class code 0x64, instance 1 are shown below.

5–56	LM10 MOTOR PROTECTION SYSTEM – INSTRUCTION MANUAL

Image 62

GE Motor Protection System, LM10 instruction manual Attribute, Access, Name/Description, Data Type, Value

Contents

Multilin LM10 Motor Protection System Instruction ManualGE Consumer & Industrial 1601-0165-A6 2008 GE Multilin Incorporated. All rights reserved 1 INTRODUCTION Table of Contents2 INSTALLATION 3 INTERFACE 6 MISCELLANEOUS 4 FUNCTIONALITY5 COMMUNICATIONS APPENDIX INDEX A-17 1-IV 1.1.1 The LM10 Relay LM10 Motor Protection System Chapter 1 Introduction1.1 Description 1.2.2 Current and Voltage Inputs 1.2.1 Features1.2 Overview 1.2.3 Relay Outputs FIGURE 1-1 Functional Block Diagram 1.2.4 Power Supply1.2.5 Block Diagram 1.3.3 Switches 1.3 Features1.3.2 LED Indicators 1.3.1 Programming and Display Unit FIGURE 1-2 LM10 Features Changes to switch settings will not take effect until power is cycledDIP Switch Position Baud Rate Table 1-1 LM10 Order Codes 1.4 Ordering1.4.1 Order Codes LM10 PHASE CURRENT SpecificationsGROUND FAULT 1.5.1 Protection Elements POWER SUPPLY POWERPOWER FACTOR 1.5.3 Control Functions 0 to 120 CONTACT INPUTStop, Reset, DeviceNet control 200 to Thermal overload CT 1.5.5 CT DimensionsGround fault CT 1.5.6 Outputs SERIAL COMMUNICATIONS EnvironmentalApprovals/Certification 1.5.8 1-12 2.1.1 DeviceNet LM10 Motor Protection System Chapter 2 Installation2.1 Wiring 2.1.2 RS232 Port 2.1.3 Control Terminals Table 2-1 Control Connections 2.1.5 Wiring Diagram 2.1.4 Sensor Pack Input FIGURE 2-4 LM10 Wiring Diagram CHAPTER 2 INSTALLATION 2.2 Mounting 2.2.1 LM10 Mounting FIGURE 2-7 PDU Door-mount Dimensions 2.2.2 PDU Door MountFIGURE 2-6 LM10 Backplate Dimensions 3.1.1 Liquid Crystal Display LM10 Motor Protection System Chapter 3 Interface3.1 PDU Operations 3.1.2 LEDs power factor, kW, average current, and current unbalance. Pressing the History button again advances to the next history record 3.2.1 Main Startup Screen 3.2.3 Configuration Menu3.2 PDU Screens and Menus 3.2.2 History Record and Status Screens Run 2 to Run 1 delay between forward and reverse or between speeds 3.3.2 Functional Details 3.3 EnerVista LM10 Software3.3.1 Description Table 3-1 EnerVista Hot Keys 4.1.1 Descriptions 4.1 Overcurrent Fault ConditionsLM10 Motor Protection System Chapter 4 Functionality FIGURE 4-1 Cold Motor Trip Curves FIGURE 4-2 Hot Motor Trip Curves CHAPTER 4 FUNCTIONALITY FIGURE 4-4 Cool Down Times 4.1.2 Trip Curves ExampleFIGURE 4-3 Trip Curve with Jam and Stall Enabled Page Table 4-1 LM10 Programmable Parameters 4.2 Configuration Settings4.2.1 Overview 4-30 4.2.2 Main MenuCONFIGURATION SETTINGSCHAPTER 4 FUNCTIONALITY 4.2.3 Language PATH Configuration Ø ENGLISH/SPANISHPATH Configuration ØØ CTs & CPTs 4.2.4 CTs and CPTs PATH Configuration ØØØØ Run 1 Setup 4.2.6 Run 1 and Run 2 SetupPATH Configuration ØØØ Starter Type 4.2.5 Starter Type Δ = phase current - average current PATH Configuration ØØØØØØ Other Settings 4.2.8 Other SettingsPATH Configuration ØØØØØ Time Delays 4.2.7 Time Delays Maintained off DevNet Fault onReset Run Hrs Auto Restart off 4.2.9 Auxiliary Relay Faults PATH Configuration ØØØØØØØ Aux Relay Faults 4.2.10 Passcode and Login PATH Configuration ØØØØØØØØ Aux Relay Faults PATH Configuration ØØØØØØØØØØ Factory Default 4.2.12 Factory DefaultPATH Configuration ØØØØØØØØØ Run Operations 4.2.11 Run Operations Run, Fault 4.3 Status Values4.3.1 Main Menu Range This value can be reset via the Reset Run Hrs configuration setting Range Overcurrent, Gr. Fault, Jam, Stall CuUnbalance, LdLoss, DevNet 4.4 History Values4.4.1 Last Trip Data Fault, Dev Stop, Voltage, Aux Sense Range 0.0 to 3200.0 A Motor Status Running AUX Sense 1 Fault4.5 Motor Start/Stop Logic Motor Stop RUN1 Switch Input Motor RUN CommandsMotor STOP Commands RUN1 PDU Command 4-44 5.1.1 Description LM10 Motor Protection System Chapter 5 Communications5.1 DeviceNet Operations 5.1.2 Poll Data Table 5-3 Poll Data Group Table 5-1 Poll Data GroupTable 5-2 Poll Data Group Table 5-4 Poll Data Group 5.1.5 DeviceNet Object 5.1.3 Identity object5.1.4 Message Router UINT = 16 bit unsigned integer Device outputs see format and mapping below 5.1.6 Assembly ObjectBaud Rate, value 0 to 2 125, 250, and 500 kbps Assembly Object, Class Code 4, Instance CHAPTER 5 COMMUNICATIONS Data Formats for Device Inputssee below Assembly Object, Class Code 4, Instance Connection Object, Class Code 5, Attributes 5.1.7 Connection ObjectConnection Object, Class Code 5, Services Connection Object, Class Code 5, Instance 2 polled input/output connection USINT = 8-bit unsigned integer UINT = 16-bit unsigned integer 5.1.8 ACK Handler Object5.1.9 Overload Object 5.1.10 Extension Object UINT = 16-bit unsigned integer Name/Description 5.1.11 Data Formats F2 Ground FaultF7 Power Transformer F1 Full Load Current 16-bit unsigned integer F10 Auxiliary Sense 2 / Run2-Run1 Time Delays F11 Auxiliary Relay Faults 16-bit bitmaskF9 Auxiliary Sense 1 / Run1-Run2 Time Delays F12 Starter Type F16 Run1-Run2 and Run2-Run1 Time Delay 16-bit unsigned integer F14 Other Settings 16-bit BitmaskF15 Poll Data Group enumeration 16-bit unsigned integer F17 Trip Class F23 16-bit Unsigned Integer F21 Motor Status 8-bit BitmaskF22 Motor Status 16-bit bitmask F24 Status Word 16-bit bitmask F25 Input Switch Status 16-bit value use only lower byte 5.1.12 Special Application Sent by scanner CANID, MACID, 0x0E, 0x64, 0x01 5.2 Serial Port 5.2.1 Description 5-64 6.1.1 Release Dates LM10 Motor Protection System Chapter 6 MiscellaneousRevision History 6.1.2 Changes to the Manual Add Assembly Object, Class Code 4, Instance 105 Poll Data Group Table 6-4 Changes to Manual Since Release A3Change to Assembly Object, Class Code 4, Instance 101, Attribute Changes to Connection Object, Class Code 5, Instance 2 polled 6.2 Warranty 6.2.1 GE Multilin Warranty CHAPTER 6 MISCELLANEOUS WARRANTY6-68 A.1.1 Description LM10 Motor Protection System Appendix AA.1 DeviceNet Overview A.1.2 Controller Area Network CAN A.1.3 DeviceNet Operations A.1.5 Pre-defined Master/Slave Connection Set A.1.6 DeviceNet FeaturesA.1.4 Explicit Messaging and Input/Output I/O Messaging A.1.7 Maximum Cable Lengths for DeviceNet Table A-2 Drop Cable Length Specification A.1.8 DeviceNet Specification HighlightsTable A-1 Trunk Cable Length Specification Description The Object Model Device Profiles A.2 LM10 and GE Fanuc 90-30 with DeviceNet A.2.3 Network ConfigurationA.2.4 Configuration Procedure A.2.1 Overview Z Also, set the Scan Interval and Reconnect Time A.2.5 Polling Input/Output ConnectionZ Select GE LM10 under GE Multilin Page Phase A values are displayed in %I00105 223 ⋅ 0.1 amps A.2.6 COS Change of State Input/Output Connection A.2.7 Cyclic Input/Output Connection A.2.8 Explicit Messaging Monitoring Data Rung 3 has a Block Move word, 3 blocks Login Configuration Level to the LM10 FIGURE A-1 Ladder Logic for Data Monitoring Making Setting Changes FIGURE A-2 Ladder Logic for Login Configuration Login User Level to the LM10 FIGURE A-3 Ladder Logic for Setting Changes FIGURE A-4 Ladder Logic for Login User A.3 LM10 and Allen-Bradley SLC500 via DeviceNet A.3.2 System SetupA.3.4 Setting Up the DeviceNet Network A.3.1 Description A.3.5 Changing the Mode of Operation A.3.6 Configuring the Slave Device A.3.7 Control and Monitoring of the LM10 A.3.8 Explicit Messaging with the LM10 Relay Table A-4 Data Table Layout Table A-3 Status Codes Provided by ODVA SpecificationA.3.9 Data Table Layout Table A-6 Data for Explicit Message Response, M1 Transferred to N20 A.3.10 Ladder LogicTable A-5 Data to Get Trip Class Instance, and Attribute Table A-7 Data to Get Motor Run TimeTable A-8 Data for Explicit Message Response, M1 Transferred to N20 FIGURE A-9 Ladder Logic, Rungs 0000 to A-25 FIGURE A-10 Ladder Logic, Rungs 0006 to A-26 FIGURE A-11 Ladder Logic, Rungs 0009 to A-27 A-28 Index Page LM10 MOTOR PROTECTION SYSTEM - INSTRUCTION MANUAL INDEX LM10 MOTOR PROTECTION SYSTEM - INSTRUCTION MANUAL