A.3.10 Ladder Logic, Table A-5 Data to Get Trip Class | GE LM10

CHAPTER A:

LM10 AND ALLEN-BRADLEY SLC500 VIA DEVICENET™

•0E (hex), 14 (decimal) = Get Attribute Single (read a single parameter)

•10 (hex), 16 (decimal) = Set Attribute Single (write a single parameter)

•32 (hex), 50 (decimal) = Get Attribute Multiple (read multiple parameters)

The MAC ID low byte is destination code 09.

The transaction body consists of the Class, Instance, Attribute, and Data bytes.

A.3.10 Ladder Logic

This discussion refers to the Ladder Logic diagrams shown on the following pages.

1.Rung 0000 to Rung 0004 are used to toggle the Bit B4/0 every 1 second; this is the input to BSL (Bit Shift Left).

2.For every 1 second toggle of B4/0, left-shift the N9:0 register.

3.The bits in the N9:0 register are used to enable Rungs 0007 to 0012.

4.Rung 0006 is used to reload the N9:0 register after overflow.

5.The COP function is used to copy the contains of the M1 file to a specific N register and transfer the values to the M0 file.

Table A–5: Data to Get Trip Class

Address	Data (hex)	Description


N31:0	0101	TXID / Command

N31:1	0008	Port / Size

N31:2	0E09	Service / MAC ID (Node 09)

N31:3	0064	Class

N31:4	0001	Instance

N31:5	002F	Attribute (Trip Class)

Table A–6: Data for Explicit Message Response, M1 Transferred to N20

Address	Data (hex)	Description


N32:0	0101	TXID / Command

N32:1	0002	Port / Size

N32:2	8E09	Service / MAC ID (Node = 09)

N32:3	Trip Class Value	Service Response Data

LM10 MOTOR PROTECTION SYSTEM – INSTRUCTION MANUAL

A–23

Image 97

GE LM10, Motor Protection System instruction manual A.3.10 Ladder Logic, Table A-5 Data to Get Trip Class

Contents

GE Consumer & Industrial LM10 Motor Protection System Instruction ManualMultilin 1601-0165-A6 2008 GE Multilin Incorporated. All rights reserved 2 INSTALLATION Table of Contents1 INTRODUCTION 3 INTERFACE 5 COMMUNICATIONS 4 FUNCTIONALITY6 MISCELLANEOUS APPENDIX A-17 INDEX 1-IV 1.1 Description LM10 Motor Protection System Chapter 1 Introduction1.1.1 The LM10 Relay 1.2 Overview 1.2.1 Features1.2.2 Current and Voltage Inputs 1.2.3 Relay Outputs 1.2.5 Block Diagram 1.2.4 Power SupplyFIGURE 1-1 Functional Block Diagram 1.3.2 LED Indicators 1.3 Features1.3.3 Switches 1.3.1 Programming and Display Unit DIP Switch Position Changes to switch settings will not take effect until power is cycledFIGURE 1-2 LM10 Features Baud Rate 1.4.1 Order Codes 1.4 OrderingTable 1-1 LM10 Order Codes LM10 GROUND FAULT SpecificationsPHASE CURRENT 1.5.1 Protection Elements POWER FACTOR POWERPOWER SUPPLY 1.5.3 Control Functions Stop, Reset, DeviceNet control CONTACT INPUT0 to 120 200 to Ground fault CT 1.5.5 CT DimensionsThermal overload CT 1.5.6 Outputs Approvals/Certification EnvironmentalSERIAL COMMUNICATIONS 1.5.8 1-12 2.1 Wiring LM10 Motor Protection System Chapter 2 Installation2.1.1 DeviceNet 2.1.2 RS232 Port Table 2-1 Control Connections 2.1.3 Control Terminals 2.1.4 Sensor Pack Input 2.1.5 Wiring Diagram CHAPTER 2 INSTALLATION FIGURE 2-4 LM10 Wiring Diagram 2.2.1 LM10 Mounting 2.2 Mounting FIGURE 2-6 LM10 Backplate Dimensions 2.2.2 PDU Door MountFIGURE 2-7 PDU Door-mount Dimensions 3.1 PDU Operations LM10 Motor Protection System Chapter 3 Interface3.1.1 Liquid Crystal Display 3.1.2 LEDs power factor, kW, average current, and current unbalance. Pressing the History button again advances to the next history record 3.2 PDU Screens and Menus 3.2.3 Configuration Menu3.2.1 Main Startup Screen 3.2.2 History Record and Status Screens Run 2 to Run 1 delay between forward and reverse or between speeds 3.3.1 Description 3.3 EnerVista LM10 Software3.3.2 Functional Details Table 3-1 EnerVista Hot Keys LM10 Motor Protection System Chapter 4 Functionality 4.1 Overcurrent Fault Conditions4.1.1 Descriptions CHAPTER 4 FUNCTIONALITY FIGURE 4-1 Cold Motor Trip Curves FIGURE 4-2 Hot Motor Trip Curves FIGURE 4-3 Trip Curve with Jam and Stall Enabled 4.1.2 Trip Curves ExampleFIGURE 4-4 Cool Down Times Page 4.2.1 Overview 4.2 Configuration SettingsTable 4-1 LM10 Programmable Parameters CONFIGURATION SETTINGSCHAPTER 4 FUNCTIONALITY 4.2.2 Main Menu4-30 PATH Configuration ØØ CTs & CPTs PATH Configuration Ø ENGLISH/SPANISH4.2.3 Language 4.2.4 CTs and CPTs PATH Configuration ØØØ Starter Type 4.2.6 Run 1 and Run 2 SetupPATH Configuration ØØØØ Run 1 Setup 4.2.5 Starter Type Δ = phase current - average current PATH Configuration ØØØØØ Time Delays 4.2.8 Other SettingsPATH Configuration ØØØØØØ Other Settings 4.2.7 Time Delays Reset Run Hrs DevNet Fault onMaintained off Auto Restart off PATH Configuration ØØØØØØØ Aux Relay Faults 4.2.9 Auxiliary Relay Faults PATH Configuration ØØØØØØØØ Aux Relay Faults 4.2.10 Passcode and Login PATH Configuration ØØØØØØØØØ Run Operations 4.2.12 Factory DefaultPATH Configuration ØØØØØØØØØØ Factory Default 4.2.11 Run Operations 4.3.1 Main Menu 4.3 Status ValuesRun, Fault Range This value can be reset via the Reset Run Hrs configuration setting 4.4.1 Last Trip Data 4.4 History ValuesRange Overcurrent, Gr. Fault, Jam, Stall CuUnbalance, LdLoss, DevNet Fault, Dev Stop, Voltage, Aux Sense Range 0.0 to 3200.0 A 4.5 Motor Start/Stop Logic AUX Sense 1 FaultMotor Status Running Motor Stop Motor STOP Commands Motor RUN CommandsRUN1 Switch Input RUN1 PDU Command 4-44 5.1 DeviceNet Operations LM10 Motor Protection System Chapter 5 Communications5.1.1 Description 5.1.2 Poll Data Table 5-2 Poll Data Group Table 5-1 Poll Data GroupTable 5-3 Poll Data Group Table 5-4 Poll Data Group 5.1.4 Message Router 5.1.3 Identity object5.1.5 DeviceNet Object UINT = 16 bit unsigned integer Baud Rate, value 0 to 2 125, 250, and 500 kbps 5.1.6 Assembly ObjectDevice outputs see format and mapping below Assembly Object, Class Code 4, Instance see below Data Formats for Device InputsCHAPTER 5 COMMUNICATIONS Assembly Object, Class Code 4, Instance Connection Object, Class Code 5, Services 5.1.7 Connection ObjectConnection Object, Class Code 5, Attributes Connection Object, Class Code 5, Instance 2 polled input/output connection 5.1.9 Overload Object 5.1.8 ACK Handler ObjectUSINT = 8-bit unsigned integer UINT = 16-bit unsigned integer UINT = 16-bit unsigned integer 5.1.10 Extension Object Attribute F7 Power Transformer F2 Ground Fault5.1.11 Data Formats F1 Full Load Current 16-bit unsigned integer F9 Auxiliary Sense 1 / Run1-Run2 Time Delays F11 Auxiliary Relay Faults 16-bit bitmaskF10 Auxiliary Sense 2 / Run2-Run1 Time Delays F12 Starter Type F15 Poll Data Group enumeration 16-bit unsigned integer F14 Other Settings 16-bit BitmaskF16 Run1-Run2 and Run2-Run1 Time Delay 16-bit unsigned integer F17 Trip Class F22 Motor Status 16-bit bitmask F21 Motor Status 8-bit BitmaskF23 16-bit Unsigned Integer F24 Status Word 16-bit bitmask 5.1.12 Special Application F25 Input Switch Status 16-bit value use only lower byte Sent by scanner CANID, MACID, 0x0E, 0x64, 0x01 5.2.1 Description 5.2 Serial Port 5-64 Revision History LM10 Motor Protection System Chapter 6 Miscellaneous6.1.1 Release Dates 6.1.2 Changes to the Manual Change to Assembly Object, Class Code 4, Instance 101, Attribute Table 6-4 Changes to Manual Since Release A3Add Assembly Object, Class Code 4, Instance 105 Poll Data Group Changes to Connection Object, Class Code 5, Instance 2 polled 6.2.1 GE Multilin Warranty 6.2 Warranty 6-68 WARRANTYCHAPTER 6 MISCELLANEOUS A.1 DeviceNet Overview LM10 Motor Protection System Appendix AA.1.1 Description A.1.3 DeviceNet Operations A.1.2 Controller Area Network CAN A.1.4 Explicit Messaging and Input/Output I/O Messaging A.1.6 DeviceNet FeaturesA.1.5 Pre-defined Master/Slave Connection Set A.1.7 Maximum Cable Lengths for DeviceNet Table A-1 Trunk Cable Length Specification A.1.8 DeviceNet Specification HighlightsTable A-2 Drop Cable Length Specification Description Device Profiles The Object Model A.2.4 Configuration Procedure A.2.3 Network ConfigurationA.2 LM10 and GE Fanuc 90-30 with DeviceNet A.2.1 Overview Z Select GE LM10 under GE Multilin A.2.5 Polling Input/Output ConnectionZ Also, set the Scan Interval and Reconnect Time Page Phase A values are displayed in %I00105 223 ⋅ 0.1 amps A.2.7 Cyclic Input/Output Connection A.2.6 COS Change of State Input/Output Connection Monitoring Data A.2.8 Explicit Messaging Rung 3 has a Block Move word, 3 blocks FIGURE A-1 Ladder Logic for Data Monitoring Login Configuration Level to the LM10 FIGURE A-2 Ladder Logic for Login Configuration Making Setting Changes FIGURE A-3 Ladder Logic for Setting Changes Login User Level to the LM10 FIGURE A-4 Ladder Logic for Login User A.3.4 Setting Up the DeviceNet Network A.3.2 System SetupA.3 LM10 and Allen-Bradley SLC500 via DeviceNet A.3.1 Description A.3.5 Changing the Mode of Operation A.3.6 Configuring the Slave Device A.3.7 Control and Monitoring of the LM10 A.3.8 Explicit Messaging with the LM10 Relay A.3.9 Data Table Layout Table A-3 Status Codes Provided by ODVA SpecificationTable A-4 Data Table Layout Table A-5 Data to Get Trip Class A.3.10 Ladder LogicTable A-6 Data for Explicit Message Response, M1 Transferred to N20 Table A-8 Data for Explicit Message Response, M1 Transferred to N20 Table A-7 Data to Get Motor Run TimeInstance, and Attribute A-25 FIGURE A-9 Ladder Logic, Rungs 0000 to A-26 FIGURE A-10 Ladder Logic, Rungs 0006 to A-27 FIGURE A-11 Ladder Logic, Rungs 0009 to A-28 Index Page LM10 MOTOR PROTECTION SYSTEM - INSTRUCTION MANUAL LM10 MOTOR PROTECTION SYSTEM - INSTRUCTION MANUAL INDEX