PR70e | Graco 334135B instruction

Instructions

PR70e™	334135B
Compact Benchtop Meter, Mix and Dispense System	EN

Use for accurate metering, mixing and dispensing of two-component sealants and adhesives in fixed ratios. Not for use with isocyanate catalyzed materials. For professional use only.

Not approved for use in explosive atmospheres or hazardous locations.

Refer to Models, page 3, for maximum working pressures.

Important Safety Instructions

Read all warnings and instructions in this manual. Save these instructions.

Image 1

Graco 334135B important safety instructions PR70e, Important Safety Instructions

Contents

PR70e Important Safety Instructions Contents Related Manuals Models Electric Shock Hazard Fire and Explosion Hazard Machine Component IdentificationIG Machine Key AB System Shut-Down Key Local Control Module LCM LCM Screen Navigation Screen Overview and Appendix C LCM SetupRun Screen Component Identification 334135B Dispense Valve Recommended PartsStandard Dispense Valves, 255179 Gun Mounted MD2 Valves, LC0120 and LC0122 Part Description Quantity Lever Actuated MD2 Valves, LC0121 and LC0123 Mixers 1301 1302 1303 Mixer Reference Number and DescriptionShroud Package Description Part Description Mounting, valve, HMI Mounting, HMI Applicator Mounting Air Filter and Ball Valve, 24R707 High Temperature Grease Footswitch Tanks Quantity Part Description 24W415 24W416 24W417 Unheated, Non-Recirculating Hose Hose Packages Recommended Parts 334135B Nylon Piston, Stainless Steel Metering Tube Assemblies Piston Package Uhmw Uhmw Piston, Stainless Steel Metering Tube Assemblies Shot Size cc Air Motor In. Air Motor Pump Tube Combination Information Machine Installation InstallationGrounding General Grounding Guidelines Install the Dispense Valve and Support Arm, if needed Install the Chemical Hoses Electrical Requirements Ground System Piston Position Calibration Setup Navigate to the Shot Mode Screen or Operator Mode Screen Perform Pressure Relief Procedure onEngaged Piston Position Manually Move the Piston Drive Block Prime Dispense Head Prime the Dispense Head Adjust Dispense Quantity Phasing AdjustmentPrepare the Machine Navigate to the Phasing Shot Calibration Screen Adjust Phasing Adjust Dispense Valve Snuff Back Operator Mode Screen Adjust Open Dispense Valve ODV Timing Navigate to the Maintenance Mode Run Screen Pressure Relief ProcedureOperation Startup Shutdown Relieve pressure. See Pressure Relief Procedure, Clean the Pump Shafts MaintenanceDisassemble and Clean the Dispense Head Schedule Remove Access Panel Install Upgrade Token Problem Cause Solution Troubleshooting Problem Cause Solution Trigger LCM Error CodesCode Name Type Causes Fixes Condition Entries in Position Calibra Prepare Machine for Kit Installation HydraCheck Kit Installation, 24W336Repair Adjust the Adjustment Screw/Cap Install Adjustment Screw/CapAdjust Shock Resistance Disassemble the Air Cylinder Air Cylinder Rebuild Instructions Re-Assemble the Air Cylinder Clean and Inspect the Parts Rear Pump Rebuild Instructions Prepare for Operation Assemble the Rear Pump Assembly Install Cylinder Piston/Cylinder Replacement Kit InstallationDisassemble Cylinder Check Valve Rebuild Kit Installation Fixed Ratio Base Parts 24V935, Pump 24V936, Pump Part Description Assembly Pump Sub-Assembly, 24S053 Collar Check Valve, Assembly LC0093 206 201 204 205 202 203 Fixed Ratio Drive Block Assembly, LC0107 24V933, Motor 24V934, Motor Part Description Air Air Cylinder, 24V933 Fixed Ratio Frame Sub-Assembly, LC0290 Ring, support Carbide Package Pump Piston Washer Screw Ball Uhmw Piston, Ceramic Metering Tube Assemblies Electrical Schematics Schematics Electrical Schematic DB25 Pin Function Pneumatic SchematicDB25 Pin Number Pin Function Description Schematics 334135B Appendix a LCM Icon Overview Position Adjust Phasing Shot AdjustAdjust Amount Adjust Disable Mode Screen Splash Screen Operator Mode ScreenShot Mode Screen Mode Selection Programming Screen Shot Amount or Stroke % Adjust Screen Maintenance Mode Run ScreenError Code Acknowledgement Screen Run Screen while Dispensing Setup Screen Password Set/Clear Screen Appendix C LCM Setup Screen OverviewPhasing Shot Calibration Screen Kits Nylon and Uhmw Piston Replacement KitsLCF Piston Size mm2 LCE Piston Size mm2 MD2 Valve Recommended Spare Parts Dimensions Dimensions Technical Data Graco Information Graco Standard Warranty