Models, Related Manuals | Graco 334135B specs

								Models
Models

System	MD2 Valve		Air Motor	Required	Machine		Maximum	Maximum
	Ratio		in. (cm)	Line	Operation		Working	Air Inlet
				Voltage	Voltage		Pressure	Pressure
							psi (MPa, bar)	psi (MPa, bar)

24S054	1:1		3 (7.6)	100-240 V

24S055	10:1
24S055	10:1			50/60 Hz,	24 VDC		3000 (21, 207)	100 (0.7, 7)
				1 phase -
24S056	1:1		4.5 (11.4)
24S056	1:1
				50 Watts
24S057	10:1			50 Watts
24S057	10:1

Related Manuals

MD2 Dispense Valve Manual

Part	Description

312185	MD2 Valve, Instructions

312394	PR70 and PR70v Feed Systems, Instructions-Parts

334135B

3

Image 3

Graco 334135B important safety instructions Models, Related Manuals

Contents

PR70e Important Safety Instructions Contents Related Manuals Models Electric Shock Hazard Fire and Explosion Hazard Component Identification MachineIG Machine Key AB System Shut-Down Key Local Control Module LCM Screen Overview and Appendix C LCM Setup LCM Screen NavigationRun Screen Component Identification 334135B Gun Mounted MD2 Valves, LC0120 and LC0122 Recommended PartsDispense Valve Standard Dispense Valves, 255179 Part Description Quantity Lever Actuated MD2 Valves, LC0121 and LC0123 Mixers Package Description Reference Number and Description1301 1302 1303 Mixer Shroud Part Description Mounting, valve, HMI Mounting, HMI Applicator Mounting Air Filter and Ball Valve, 24R707 High Temperature Grease Footswitch Tanks Quantity Part Description 24W415 24W416 24W417 Unheated, Non-Recirculating Hose Hose Packages Recommended Parts 334135B Nylon Piston, Stainless Steel Metering Tube Assemblies Piston Package Uhmw Uhmw Piston, Stainless Steel Metering Tube Assemblies Shot Size cc Air Motor In. Air Motor Pump Tube Combination Information General Grounding Guidelines InstallationMachine Installation Grounding Install the Dispense Valve and Support Arm, if needed Install the Chemical Hoses Electrical Requirements Ground System Piston Position Calibration Setup Manually Move the Piston Drive Block Perform Pressure Relief Procedure onNavigate to the Shot Mode Screen or Operator Mode Screen Engaged Piston Position Prime Dispense Head Prime the Dispense Head Navigate to the Phasing Shot Calibration Screen Phasing AdjustmentAdjust Dispense Quantity Prepare the Machine Adjust Phasing Adjust Dispense Valve Snuff Back Operator Mode Screen Adjust Open Dispense Valve ODV Timing Startup Pressure Relief ProcedureNavigate to the Maintenance Mode Run Screen Operation Shutdown Relieve pressure. See Pressure Relief Procedure, Schedule MaintenanceClean the Pump Shafts Disassemble and Clean the Dispense Head Remove Access Panel Install Upgrade Token Problem Cause Solution Troubleshooting Problem Cause Solution Entries in Position Calibra LCM Error CodesTrigger Code Name Type Causes Fixes Condition HydraCheck Kit Installation, 24W336 Prepare Machine for Kit InstallationRepair Install Adjustment Screw/Cap Adjust the Adjustment Screw/CapAdjust Shock Resistance Disassemble the Air Cylinder Air Cylinder Rebuild Instructions Re-Assemble the Air Cylinder Clean and Inspect the Parts Rear Pump Rebuild Instructions Prepare for Operation Assemble the Rear Pump Assembly Piston/Cylinder Replacement Kit Installation Install CylinderDisassemble Cylinder Check Valve Rebuild Kit Installation Fixed Ratio Base Parts 24V935, Pump 24V936, Pump Part Description Assembly Pump Sub-Assembly, 24S053 Collar Check Valve, Assembly LC0093 206 201 204 205 202 203 Fixed Ratio Drive Block Assembly, LC0107 24V933, Motor 24V934, Motor Part Description Air Air Cylinder, 24V933 Fixed Ratio Frame Sub-Assembly, LC0290 Ring, support Carbide Package Pump Piston Washer Screw Ball Uhmw Piston, Ceramic Metering Tube Assemblies Electrical Schematics Schematics Electrical Schematic Pneumatic Schematic DB25 Pin FunctionDB25 Pin Number Pin Function Description Schematics 334135B Appendix a LCM Icon Overview Amount Adjust Phasing Shot AdjustPosition Adjust Adjust Mode Selection Programming Screen Splash Screen Operator Mode ScreenDisable Mode Screen Shot Mode Screen Run Screen while Dispensing Maintenance Mode Run ScreenShot Amount or Stroke % Adjust Screen Error Code Acknowledgement Screen Appendix C LCM Setup Screen Overview Setup Screen Password Set/Clear ScreenPhasing Shot Calibration Screen LCE Piston Size mm2 Nylon and Uhmw Piston Replacement KitsKits LCF Piston Size mm2 MD2 Valve Recommended Spare Parts Dimensions Dimensions Technical Data Graco Information Graco Standard Warranty