Foreword, Contact Info | Grizzly G0634Z manual

INTRODUCTION

Foreword

We are proud to offer the Model G0633/G0634 Jointer/Planer Combination Machine. This machine is part of a growing Grizzly family of fine woodworking machinery. When used according to the guidelines set forth in this manual, you can expect years of trouble-free, enjoyable operation and proof of Grizzly’s commitment to customer satisfaction.

The specifications, drawings, and photographs illustrated in this manual represent the Model G0633/G0634 when the manual was prepared. However, owing to Grizzly’s policy of continuous improvement, changes may be made at any time with no obligation on the part of Grizzly.

For your convenience, we always keep current Grizzly manuals available on our website at www. grizzly.com. Any updates to your machine will be reflected in these manuals as soon as they are complete. Visit our site often to check for the lat- est updates to this manual!

-2-

Contact Info

If you have any comments regarding this manual, please write to us at the address below:

Grizzly Industrial, Inc.

C/O Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

We stand behind our machines. If you have any service questions or parts requests, please call or write us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone: (570) 546-9663

Fax: (800) 438-5901

E-Mail: techsupport@grizzly.com

Web Site: http://www.grizzly.com

G0633/G0634 Jointer/Planer Combo Machine

Image 20

Grizzly G0634Z manual Foreword, Contact Info

Contents

Machine Inventory G0634Z only Figure To rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List Description Table Assembly Cutterhead & Motor Cutterhead & Motor Parts List Description Drive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MM Safety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact Info G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controls G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers 220V Operation Amperage DrawCircuit Requirements Plug/Receptacle Type Grounding Set Up Safety Items Needed for SetupUnpacking Description Qty Common Components Qty Jointer/Planer Assembly Not shown InventoryG0633 only Figure G0634 only Figure Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor Load Moving & Placing Base Unit Front and right rear lifting hole Locations Setting Outfeed Table Height To install the cutterhead guardCutterhead Guard To set the outfeed table height To connect a dust collection hose Knife Setting GaugeDust Collection Test Run To test run the machine Recommended Adjustments Tighten V-Belts Operation Safety OperationsPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls To change the machine for jointer opera- tions Planer dust port in down position Stock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointer Squaring Stock Thickness Planer Specific Rules Surface Planing To surface plane on the jointer Edge Jointing To edge joint on the jointer Bevel Cutting To bevel cut on the jointer Basic Planer Operation Basic steps of operating the planer are as follows Accessories H1302 H4979 H4977 Belts CleaningSchedule Lubrication Roller chainsPage Table Jointer TroubleshootingMotor & Electrical Cutting Jointer and Planer 43 or Checking/Adjusting Jointer Table Parallelism Checking Outfeed Table Parallelism To correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Calibrating Depth Scale Pulley AlignmentTo calibrate the depth scale To align the pulleys Setting Fence Stops To set the 90˚ fence stop To set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers Adjusting Gibs To adjust the table gibs Table Parallelism Adjustments To adjust the table parallelismPlaner Table Parallelism Table Parallelism Inspection To adjust feed roller spring tension Spring Tension Anti-Kickback Fingers G0633/G0634 magnetic switch Electrical Components Wiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM 801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page