Planer Table Parallelism | Grizzly G0634Z specs

Planer Table
Parallelism
Maximum Allowable Tolerances:
Cutterhead/Table Side-to-Side	0.002"
Head Casting/Table Front/Back	0.020"
Tools Needed:	Qty
Rotacator	1
Wrench 12mm	1
Hex Wrench 4mm	1
Hex Wrench 8mm	1

Table parallelism is critical to the operation of the planer. As such, it is essential that the planer table is parallel with the cutterhead (within 0.002") from side-to-side, as illustrated in Figure 75.

��

��

��

��

��

��

��

��

��

��

��

Figure 76. Front-to-back parallelism.

Table Parallelism Inspection

The easiest way to determine if your planer table has a parallelism problem with the headstock is to plane a workpiece and measure the thickness in multiple locations. If the workpiece is tapered from left-to-right or from front-to-back, then parallelism may be a problem.

Use your Rotacator (Page 32) to further inspect the table parallelism. If you do not have a Rotacator, a wood block and feeler gauges may be used, but extra care must be taken to ensure

��

��

accuracy. If the table is not within the maximum allowable tolerances, it must be adjusted.

��

��

Figure 75. Side-to-side parallelism of table and

cutterhead.

How the planer table sits in relation to the head casting from front-to-back is also important (see Figure 76). The tolerances on the front-to-back positioning are not as critical as the cutterhead/ table side-to-side positioning. Therefore, the max- imum allowable tolerance for the front-to-back parallelism is not more than 0.020".

-50-

Table Parallelism Adjustments

The table is adjusted with the set screws on the cylinder liner.

To adjust the table parallelism:

1.DISCONNECT THE JOINTER/PLANER FROM THE POWER SOURCE!

2.Raise the planer table as far as possible.

G0633/G0634 Jointer/Planer Combo Machine

Image 68

Grizzly G0634Z manual Planer Table Parallelism, Table Parallelism Inspection, Table Parallelism Adjustments

Contents

Machine Inventory G0634Z only Figure To rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List Description Table Assembly Cutterhead & Motor Cutterhead & Motor Parts List Description Drive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MM Safety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact Info G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controls G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers 220V Operation Amperage DrawCircuit Requirements Plug/Receptacle Type Grounding Set Up Safety Items Needed for SetupUnpacking Description Qty Common Components Qty Jointer/Planer Assembly Not shown InventoryG0633 only Figure G0634 only Figure Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor Load Moving & Placing Base Unit Front and right rear lifting hole Locations Setting Outfeed Table Height To install the cutterhead guardCutterhead Guard To set the outfeed table height To connect a dust collection hose Knife Setting GaugeDust Collection Test Run To test run the machine Recommended Adjustments Tighten V-Belts Operation Safety OperationsPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls To change the machine for jointer opera- tions Planer dust port in down position Stock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointer Squaring Stock Thickness Planer Specific Rules Surface Planing To surface plane on the jointer Edge Jointing To edge joint on the jointer Bevel Cutting To bevel cut on the jointer Basic Planer Operation Basic steps of operating the planer are as follows Accessories H1302 H4979 H4977 Belts CleaningSchedule Lubrication Roller chainsPage Table Jointer TroubleshootingMotor & Electrical Cutting Jointer and Planer 43 or Checking/Adjusting Jointer Table Parallelism Checking Outfeed Table Parallelism To correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Calibrating Depth Scale Pulley AlignmentTo calibrate the depth scale To align the pulleys Setting Fence Stops To set the 90˚ fence stop To set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers Adjusting Gibs To adjust the table gibs Table Parallelism Adjustments To adjust the table parallelismPlaner Table Parallelism Table Parallelism Inspection To adjust feed roller spring tension Spring Tension Anti-Kickback Fingers G0633/G0634 magnetic switch Electrical Components Wiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM 801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page