Clean Up, Site Considerations, Floor Load | Grizzly G0634Z guide

Clean Up

The unpainted surfaces are coated with a waxy oil to prevent corrosion during shipment. Remove this protective coating with a solvent cleaner or citrus-based degreaser such as Grizzly’s G7895 Citrus Degreaser. To clean thoroughly, some parts must be removed. For optimum perfor- mance from your machine, clean all moving parts or sliding contact surfaces. Avoid chlo- rine-based solvents, such as brake parts cleaner that may damage painted surfaces. Always follow the manufacturer’s instructions when using any type of cleaning product.

Gasoline and petroleum products have low flash points and can explode or cause fire if used to clean machinery. DO NOT use these products to clean the machinery.

Many cleaning solvents are toxic if inhaled. Minimize your risk by only using these products in a well ventilated area.

G7895—Grizzly Citrus Degreaser

This natural, citrus-based degreaser is a great solution for removing export grease, and it’s much safer to work around than nasty solvents.

Figure 6. Grizzly citrus degreaser.

-16-

Site Considerations

Floor Load

Refer to the Machine Data Sheet for the weight and footprint specifications of your machine. Some residential floors may require additional reinforcement to support both the machine and operator.

Placement Location

Consider existing and anticipated needs, size of material to be processed through each machine, and space for auxiliary stands, work tables or other machinery when establishing a location for your new machine. See Figure 7 for the minimum working clearances.

��

	��
	��	�
	��	�
	��	��
	��	��
		��
	��
	��
	��	��
	��	��
	��	��
	��	��
	��

��

��

��

Figure 7. Minimum working clearances.

Children and visitors may be seriously injured if unsuper- vised around this machine. Lock entrances to the shop or disable start switch or power connection to prevent unsupervised use.

G0633/G0634 Jointer/Planer Combo Machine

Image 34

Grizzly G0634Z manual Clean Up, Site Considerations, Floor Load, Placement Location

Contents

Machine Inventory G0634Z only Figure Tools Needed Qty Replacing Carbide Inserts G0634ZTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List Description Table Assembly Cutterhead & Motor Cutterhead & Motor Parts List Description Drive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MM Safety Labels and Cosmetic Parts H4978 T20446 H4979 AccessoriesH9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact Info G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controls G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Circuit Requirements 220V OperationAmperage Draw Plug/Receptacle Type Grounding Unpacking Set Up SafetyItems Needed for Setup Description Qty G0633 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0634 only Figure Hardware Recognition Chart Site Considerations Clean UpPlacement Location Floor Load Moving & Placing Base Unit Front and right rear lifting hole Locations Cutterhead Guard Setting Outfeed Table HeightTo install the cutterhead guard To set the outfeed table height Dust Collection Knife Setting GaugeTo connect a dust collection hose Test Run To test run the machine Recommended Adjustments Tighten V-Belts Operation Safety OperationsPage Basic Planer Controls To set up the machine for planer operationsJointer-Planer Conversion To change the machine for jointer opera- tions Planer dust port in down position Stock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointer Squaring Stock Thickness Planer Specific Rules Surface Planing To surface plane on the jointer Edge Jointing To edge joint on the jointer Bevel Cutting To bevel cut on the jointer Basic Planer Operation Basic steps of operating the planer are as follows Accessories H1302 H4979 H4977 Schedule CleaningBelts Lubrication Roller chainsPage Motor & Electrical TroubleshootingTable Jointer Cutting Jointer and Planer 43 or Checking/Adjusting Jointer Table Parallelism Checking Outfeed Table Parallelism Checking Infeed Table Parallelism Correcting Outfeed Table to Cutterhead ParallelismTo correct outfeed table parallelism To adjust the jointer table parallelism Adjusting Jointer Table ParallelismInfeed Table to Cutterhead Parallelism on Inspecting Knives G0633 Only To inspect the knives with the knife setting gaugeTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To calibrate the depth scale Calibrating Depth ScalePulley Alignment To align the pulleys Setting Fence Stops To set the 90˚ fence stop To adjust the table lock levers Adjusting Table Lock LeversTo set the 45 fence stop Adjusting Gibs To adjust the table gibs Planer Table Parallelism Table Parallelism AdjustmentsTo adjust the table parallelism Table Parallelism Inspection To adjust feed roller spring tension Spring Tension Anti-Kickback Fingers G0633/G0634 magnetic switch Electrical Components Wiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM 801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page