801 800 806 807 803 805 808 809 810 | Grizzly G0634Z specs

Safety Labels and Cosmetic Parts

801 802

800

806

807

803 804

805

808

806

38

809

810

REF	PART #	DESCRIPTION

38	G8588	GRIZZLY NAMEPLATE-SMALL
800	PLABEL-12	READ MANUAL 2" X 3 5/16"
801	PLABEL-37	RESPIRATOR/GLASSES LABEL
802	P0633802	MACHINE ID LABEL G0633
802	P0634802	MACHINE ID LABEL G0634
803	P0633803	CUTTERHEAD GUARD WARNING LABEL
804	PLABEL-15	EAR PROTECTION 2"X3 5/16"H

REF	PART #	DESCRIPTION

805	P0633805	DISCONNECT POWER LABEL
806	P0633806	CHANGING OPERATIONS WARNING LABEL
807	PPAINT-1	GRIZZLY GREEN PAINT
808	PPAINT-11	GREY PUTTY TOUCH UP PAINT
809	PLABEL-14	ELECTRICITY LABEL
810	P0633810	MODEL NUMBER LABEL G0633
810	P0634810	MODEL NUMBER LABEL G0634

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

G0633/G0634 Jointer/Planer Combo Machine

-65-

Image 83

Grizzly G0634Z manual 801 800 806 807 803 805 808 809 810

Contents

G0634Z only Figure Machine Inventory To rotate or change a carbide insert Replacing Carbide Inserts G0634ZTools Needed Qty Machine Data Sheet Cutting Capacities Planer Stand Assembly Description Stand Parts List Table Assembly Cutterhead & Motor Description Cutterhead & Motor Parts List Drive Assembly Breakdown Planer Table Limit Switch Fence/Guard PR01M EXT Retaining Ring 10MM Fence/Guard Parts List Safety Labels and Cosmetic Parts H9893-Carbide Inserts 10 Pack AccessoriesH4978 T20446 H4979 JOINTER/PLANER Combination Machine Page Table of Contents Contact Info Foreword G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0634 identification and controls Identification G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers Plug/Receptacle Type Grounding 220V OperationAmperage Draw Circuit Requirements Description Qty Set Up SafetyItems Needed for Setup Unpacking G0634 only Figure Common Components Qty Jointer/Planer Assembly Not shownInventory G0633 only Figure Hardware Recognition Chart Floor Load Clean UpPlacement Location Site Considerations Front and right rear lifting hole Locations Moving & Placing Base Unit To set the outfeed table height Setting Outfeed Table HeightTo install the cutterhead guard Cutterhead Guard To connect a dust collection hose Knife Setting GaugeDust Collection To test run the machine Test Run Tighten V-Belts Recommended Adjustments Operations Operation SafetyPage Jointer-Planer Conversion To set up the machine for planer operationsBasic Planer Controls Planer dust port in down position To change the machine for jointer opera- tions Correct and incorrect grain alignment To cutterhead jointer Stock Inspection and Requirements Thickness Planer Specific Rules Squaring Stock To surface plane on the jointer Surface Planing To edge joint on the jointer Edge Jointing To bevel cut on the jointer Bevel Cutting Basic steps of operating the planer are as follows Basic Planer Operation Accessories H4979 H4977 H1302 Belts CleaningSchedule Roller chains LubricationPage Table Jointer TroubleshootingMotor & Electrical 43 or Cutting Jointer and Planer Checking Outfeed Table Parallelism Checking/Adjusting Jointer Table Parallelism To correct outfeed table parallelism Correcting Outfeed Table to Cutterhead ParallelismChecking Infeed Table Parallelism Infeed Table to Cutterhead Parallelism on Adjusting Jointer Table ParallelismTo adjust the jointer table parallelism To inspect the knives with a straightedge To inspect the knives with the knife setting gaugeInspecting Knives G0633 Only Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 To align the pulleys Calibrating Depth ScalePulley Alignment To calibrate the depth scale To set the 90˚ fence stop Setting Fence Stops To set the 45 fence stop Adjusting Table Lock LeversTo adjust the table lock levers To adjust the table gibs Adjusting Gibs Table Parallelism Inspection Table Parallelism AdjustmentsTo adjust the table parallelism Planer Table Parallelism Spring Tension To adjust feed roller spring tension Anti-Kickback Fingers Electrical Components G0633/G0634 magnetic switch Wiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List PR01M EXT Retaining Ring 10MM Fence/Guard List 801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page