Operations, Operation Safety | Grizzly G0634Z manual

SECTION 4: OPERATIONS

Operation Safety		Basic Jointer
		Controls

Damage to your eyes, lungs, and ears could result from using this machine without proper protective gear. Always wear safety glasses, a respirator, and hearing protection when operating this machine.

Loose hair and cloth-

ing could get caught in

machinery and cause seri-

ous personal injury. Keep

loose clothing and long

hair away from moving machinery.

NOTICE

If you have never used this type of machine or equipment before, WE STRONGLY REC- OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.

This section covers the basic controls used dur- ing routine jointer operations. To use the machine as a planer, you must perform a changeover (see Jointer-Planer Conversion, Page 24)

START Button: Starts motor only if the EMERGENCY OFF button is in the out position.

OFF Button: Stops motor when pushed in.

EMERGENCY OFF Button: Disables the START button. Enable the START button by twisting the EMERGENCY OFF button until it pops out.

	START
	Button
	OFF
EMERGENCY	Button
EMERGENCY
OFF Button

Figure 18. START/STOP button locations.

-22-	G0633/G0634 Jointer/Planer Combo Machine

Image 40

Grizzly G0634Z manual Operations, Operation Safety

Contents

Machine Inventory G0634Z only Figure Tools Needed Qty Replacing Carbide Inserts G0634ZTo rotate or change a carbide insert Machine Data Sheet Cutting Capacities Planer Stand Assembly Stand Parts List Description Table Assembly Cutterhead & Motor Cutterhead & Motor Parts List Description Drive Assembly Breakdown Planer Table Limit Switch Fence/Guard Fence/Guard Parts List PR01M EXT Retaining Ring 10MM Safety Labels and Cosmetic Parts H4978 T20446 H4979 AccessoriesH9893-Carbide Inserts 10 Pack JOINTER/PLANER Combination Machine Page Table of Contents Foreword Contact Info G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Identification G0634 identification and controls G0633/G0634 Jointer/Planer Combo Machine G0633/G0634 Jointer/Planer Combo Machine Additional Safety Instructions for Jointers Additional Safety Instructions for Planers 220V Operation Amperage DrawCircuit Requirements Plug/Receptacle Type Grounding Set Up Safety Items Needed for SetupUnpacking Description Qty Common Components Qty Jointer/Planer Assembly Not shown InventoryG0633 only Figure G0634 only Figure Hardware Recognition Chart Clean Up Placement LocationSite Considerations Floor Load Moving & Placing Base Unit Front and right rear lifting hole Locations Setting Outfeed Table Height To install the cutterhead guardCutterhead Guard To set the outfeed table height Dust Collection Knife Setting GaugeTo connect a dust collection hose Test Run To test run the machine Recommended Adjustments Tighten V-Belts Operation Safety OperationsPage Basic Planer Controls To set up the machine for planer operationsJointer-Planer Conversion To change the machine for jointer opera- tions Planer dust port in down position Stock Inspection and Requirements Correct and incorrect grain alignment To cutterhead jointer Squaring Stock Thickness Planer Specific Rules Surface Planing To surface plane on the jointer Edge Jointing To edge joint on the jointer Bevel Cutting To bevel cut on the jointer Basic Planer Operation Basic steps of operating the planer are as follows Accessories H1302 H4979 H4977 Schedule CleaningBelts Lubrication Roller chainsPage Motor & Electrical TroubleshootingTable Jointer Cutting Jointer and Planer 43 or Checking/Adjusting Jointer Table Parallelism Checking Outfeed Table Parallelism Checking Infeed Table Parallelism Correcting Outfeed Table to Cutterhead ParallelismTo correct outfeed table parallelism To adjust the jointer table parallelism Adjusting Jointer Table ParallelismInfeed Table to Cutterhead Parallelism on Inspecting Knives G0633 Only To inspect the knives with the knife setting gaugeTo inspect the knives with a straightedge Adjusting/Replacing Knives G0633 To adjust/replace the knives Replacing Carbide Inserts G0634 Calibrating Depth Scale Pulley AlignmentTo calibrate the depth scale To align the pulleys Setting Fence Stops To set the 90˚ fence stop To adjust the table lock levers Adjusting Table Lock LeversTo set the 45 fence stop Adjusting Gibs To adjust the table gibs Table Parallelism Adjustments To adjust the table parallelismPlaner Table Parallelism Table Parallelism Inspection To adjust feed roller spring tension Spring Tension Anti-Kickback Fingers G0633/G0634 magnetic switch Electrical Components Wiring Diagram Stand Assembly Parts Breakdown Frame Table Assembly Parts Breakdown & List Cutterhead & Motor Breakdown Planer Dust Port Drive Assembly Breakdown & List Planer Table Breakdown & List Limit Switch Breakdown & List Fence/Guard Breakdown & List Fence/Guard List PR01M EXT Retaining Ring 10MM 801 800 806 807 803 805 808 809 810 Warranty and Returns Page Page