Default Configuration Settings | Hand Held Products 3700 CCD

C.4 Default Configuration Settings

The following is a summary of default configuration settings.

Configuration CommandDefault Settings

ACK / NAK	Disabled
Baud Rate	9600
Beeper Mode	Disable beeper
Data Bits:	7
No Read Message	“NR”
Parity	Even
Postamble	CR LF
Preamble	Port ID Code ID
Read Timeout	Timeout ends a read attempt, 1.5 seconds
RTS/CTS	Disabled
Stop Bit:	1
Trigger Mode	Serial Trigger or External Trigger, Read
	Once
Votes	3 votes for port 1 and 1 vote for port 2
XON/XOFF	Disabled
Symbology Configuration	Default Settings
Codabar	Enabled
Send Start/Stop	Yes
Minimum Length	6
Maximum Length	60
Code 39	Enabled
Require Checksum	No
Send Checksum	No
Minimum Length	1
Maximum Length	48
Code 128	Enabled
Minimum Length	1
Maximum Length	80
EAN 8/13	Enabled
I 2 of 5	Disabled
Require Checksum	No
Send Checksum	No
Minimum Length	6
Maximum Length	80
UPC A/E	Enabled

Serial Commands Summary

C–3

Image 61

Hand Held Products 3700 CCD manual Default Configuration Settings, Configuration CommandDefault Settings

Contents

SCANTEAMR3700 CCD Disclaimer Patents Page Table of Contents Chapter Configuring the Scanteam Serial Commands Summary Technical SpecificationsCCD Operation and Bar Code Scanning Ascii Conversion Table List of Tables Intended Audience PrefaceOverview of the Technical Manual Related Publications Introduction Scanteam 3700 DescriptionScanteam 3700 Hardware Description Interface Port Scanteam 3700 Software DescriptionNonvolatile Memory Basic System Operation System Hardware Description Mechanical Layout General Characteristics Audible Indicator Single Modular Input /Output/Power PortOperating Theory Mounting Inserts Communications Port Scanner/Host CommunicationAsynchronous Serial Ascii Interface Auxiliary Trigger Hardwire Pinouts Power Requirements General Preparation for Use SET-UP and Installation Set-up Checklist Set-up Procedure for EvaluationPreparation To setup serial communications to the scanner Set-up Procedure Installation in the Host Instrument Top View Examples of Scanteam 3700 Barcode Orientation Pitch or Roll Scanner Illumination Clearance Preparation Configuring the Scanteam Command Format Command ConventionsData string Reset Command a Operational CommandsDisable Decoding Command DC4 Enable Decoding Command DC2 Save Configuration Command Z Serial Trigger CommandSave Configuration 3C 5A 3E Serial Trigger 3C 31 3E Configuration Commands Command Ka baud, parity, stop bits, data bits Parameter Set Communications Port Command KaOption Code ID Value Definition Command Kd enable, data ParameterScanteam 3700 Code ID Values Command Ke enable, data Parameter Set Postamble Command Ke Command Kf mode Parameter Set Communications Protocol Command Kf Command Kg modeglobal, modeport1, modeport2, # Parameter Set Trigger Mode Command KgSet Read Timeout Command Kh Command Kk enable, data Parameter Set No Read Message Command KkSet Votes Command Km Set Code 39 Command Kp Command Ks enable UPC, enable EAN Parameter Set UPC A/E, EAN 8/13 Command Ks Set Beeper Mode Command Ku Set Code 128 Command KtSet Scan Rate Command Kv Configuration Status Query Commands Default Configuration Settings Default Operating ParametersDefault Configuration Symbology Settings Maintenance SERVICE/TECHNICAL AssistanceTroubleshooting Guide Troubleshooting Hints Troubleshooting Checklist Diagnostic ProcedureProblem Possible Cause Solution Scanteam 3700 Troubleshooting Checklist Product Service Department Obtaining Factory Service Out Of Warranty Service Service Under WarrantyHelp Desk Followed during installation Chapter Scanteam 3700 Removal/Replacement Service/Technical Assistance CCD Operation and BAR Code Scanning a Scanning and Decoding a Bar Code SymbolObjectives CCD Sensor LED ReflectorPeak Detectors and Comparator Timing Sequence Microprocessor Bar Code Basics and Scanning Tips Closer Look At Bar Code SymbolsBar Code Scanning Optical Specifications Technical SpecificationsScanner Performance Skew Angle MRD minimum reflective difference 37.5%Pitch Angle Light Source Illumination Electrical Specifications Mechanical Specifications Environmental Specifications Bar Code Symbol Specifications To Host System Scanteam 3700 Interface Cable Command Format Serial Commands Summary Individual Configuration Query CommandFormatKa? Kd? Configuration CommandDefault Settings Default Configuration SettingsSymbology Configuration Default Settings Serial Commands Summary Control Function Definitions Ascii Conversion Table Ascii Conversion Table Scanteam 3700 Glossary Glossary-2 Glossary-3 Glossary-4 Glossary-5 Glossary-6 Index Scanteam Index-3 Index-4 Scanteam 3700 Limited Warranty Jordan Road Box Skaneateles Falls, New York 3700/TM Rev E