Keyboard Style Selections | Hand Held Products 5700 specs

Keyboard Style Selections

Keyboard Style

Note: The Keyboard Style Table below applies the SCANTEAM 5700 software prior to software revision level 2.0.

This programming selection allows you to program the scanner to support special keyboard features, such as CAPS LOCK, SHIFT LOCK, Data Entry, and CTRL+ codes. These special keyboard features are shown in the chart below. Default = Style A.

Keyboard Style

(If terminal is not listed, then no secondary type keyboard is supported.)

Terminal	Style A	Style B	Style C	Style D	Style E
IBM PC/XT	XT	CAPS LOCK	SHIFT LOCK	“CTRL” + ASCII [	Gr DOS SHIFT LOCK

IBM PC/AT	AT	CAPS LOCK	SHIFT LOCK	“CTRL” + ASCII [	Gr DOS SHIFT LOCK

IBM PS2 (50–80)	NORM	CAPS LOCK	SHIFT LOCK	“CTRL” + ASCII [	Gr DOS SHIFT LOCK

HDS 2000, 3200	T/W	“CTRL +”

IBM 3180 (122 Key)	T/W	D/E

COMTERM 6178	T/W	D/E

TELEX (88 Key)	T/W	D/E

SIEMENS 9758	NORM	CAPS LOCK

NCR 7052	34Key	56 Key	122 Key Caps On	122 Key Caps Off

DEC	Norm	“CTRL +”	MAKE / BREAK

[ASCII function codes (00–1F) are sent to the terminal via a “CTRL+” sequence (i.e., ‘CR’=CTRL+M)

✱Style A

Style B

Style C

Style D

Style E

3–6	SCANTEAM 5700 User’s Guide

Image 48

Hand Held Products 5700 manual Keyboard Style Selections

Contents

Decoded Output Disclaimer Scanteam 5700 User’s Guide FCC Class B Compliance StatementCanadian Notice A. Statement Patents Table of Contents Protocol Selection Serial Wedge Output Selection Require Data Format Data Format EditorMarker Beam Selection AutoTrigger Selection Foreign Keyboard Selection Industrial Symbology Selections Keyboard Function Relationships Supported Interface Keys Maintenance Troubleshooting Obtaining Factory Service Technical Support Introduction Model Number 5X00/A-12 Scanner Identification Connecting the Scanner Cable, Keyboard, and Terminal will vary Scanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PC AT and Compatibles Interface Default IBM PC, Wand Emulation InterfaceIBM PS/2 and Compatibles Interface IBM PC XT and Compatibles Interface IBM 4683 Interface Code EANCode Ocia Interface OCR, RS232 Interface Supported Terminals Program Terminal InterfaceTerminal Models Terminal I.D ICL Reset Factory Settings Status CheckQuick Suffix Selections Dual Interface Programming Instructions Dual Interface Programming Notes Code 39 Wand Emulation Selection Same Code Wand Emulation SelectionRS-232 Selection Laser Emulation Selection Dual Interface Enable/Disable Selection Switched Power Mode SelectionsLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Prefix Selection Primary Interface Suffix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Prefix Selection Secondary Interface Suffix Selection Example 1 Add Suffix for Specific Symbology Example 2 Add Suffix for ALL SymbologiesPrefix and Suffix Examples Example 4 To Clear a Specific Prefix Entry Symbology Code Hex Value Beeper Volume Selection Output Delays Selection Reread Delay Selection Good Read Delay SelectionLaser Voting Selection Buffered Scans Selection Code I.D. Transmit SelectionAIM I.D. Transmit Selection Function Code Transmit Selection CTS Check Selection Baud Rate Selection RS-232 Word Length Selection Parity Selection Protocol Selection Serial Wedge Output Selection ➎ Editor Command Sequences ➋ Terminal Type➌ Code I.D ➍ Length Require Data Format Data Format Editor Send Commands Move CommandsSearch Commands Miscellaneous Commands Data Formatter Example UPC a with 5 digit addenda Scanteam 5700 User’s Guide Introduction Marker Beam Selection AutoTrigger Selection Transmission Rate Selection Wake Up Pulse SelectionOutput Polarity Selection Foreign Keyboard Selection AT Direct Connect Selection NCR 7052 Keypad Selection Keyboard Style Selections Keyboard Style Keyboard Style Selections Keyboard Style Modifiers Code 39 Selections Codabar Selection Message Length Check Character Code 39 Selection Append Minimum Maximum Full Ascii Chart Code 93 Selection Interleaved 2 of 5 Selection Check Digit Code 2 of 5 Selection Matrix 2 of 5 Selection Code 11 Selection Code 128 Selection Code 128 Function Character Selection Code 16K Selection Code 49 Selection EAN Selection Isbn UPC Selection UPC E1 EAN Addenda Selection UPC Addenda Selection MSI Selection Plessey Selection Scanteam 5700 User’s Guide Page Download New Firmware Memory Upload Scanteam 5700 User’s Guide Clone Destination Clone Master+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Keyboard Function Relationships Function Code HEX/ASCII Value Full Ascii Ctrl +Country Codes IBM AT/XT PS/2 Compatibles, IBM XTs Memorex TelexCompatibles Harris IBM, Memorex Telex Supported Esprit 200 Ansi Ascii Bull BDS-7 Wyse WY-60/150 HoneywellHDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only 5700-X4 Laser Compatible Bar Image +12VDC Input Pin Type D Female Wand Emulation RS-232 Laser Output Maintenance Cleaning the Scan Window Replacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Obtaining Factory Service Welch Allyn, Inc Welch Allyn North AmericaEurope Limited Warranty Scanteam 5700 User’s Guide Serial Interface Menu Defaults Output Selections General Operating Menu Defaults Keyboard Selections Symbology Menu Defaults Industrial Codabar Selections Code 11 Selections Symbology Menu Defaults Retail EAN / UPC Addenda Selections Scanteam 5700 User’s Guide Page Page Page EAN Interleaved 2Matrix 2 Code 2