Reset Factory Settings, Status Check | Hand Held Products 5700

Reset Factory Settings

Scanning the Factory Default Settings bar code resets the scanner to the original factory settings, clearing any programming changes you may have made.

Factory Default Settings

Status Check

Scan the Show Software Revision bar code to transmit the software revision level to the host terminal. The software revision will be printed out as “WA34310XXX.” (The “X’s” will vary according to the firmware ID.)

Show Software Revision

Quick Suffix Selections

If your application requires it, scan the Program Carriage Return Suffix bar code to program a carriage return (CR) suffix for all enabled bar code symbologies. Scanning this bar code clears all previously programmed prefixes and suffixes.

Scan the Clear Bar Code Suffix bar code to disable (or clear) all previously programmed prefixes and suffixes (e.g., the carriage return suffix).

Program Carriage Return Suffix

Clear Bar Code Suffix

SCANTEAM 5700 User’s Guide

1–13

Image 21

Hand Held Products 5700 manual Reset Factory Settings, Status Check, Quick Suffix Selections

Contents

Decoded Output Disclaimer FCC Class B Compliance Statement Scanteam 5700 User’s GuideCanadian Notice A. Statement Patents Table of Contents Require Data Format Data Format Editor Protocol Selection Serial Wedge Output SelectionMarker Beam Selection AutoTrigger Selection Foreign Keyboard Selection Keyboard Function Relationships Supported Interface Keys Industrial Symbology Selections Obtaining Factory Service Technical Support Maintenance Troubleshooting Introduction Scanner Identification Model Number 5X00/A-12 Cable, Keyboard, and Terminal will vary Connecting the Scanner Scanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PC, Wand Emulation Interface IBM PC AT and Compatibles Interface DefaultIBM PS/2 and Compatibles Interface IBM PC XT and Compatibles Interface IBM 4683 Interface Code EANCode Ocia Interface OCR, RS232 Interface Supported Terminals Program Terminal InterfaceTerminal Models Terminal I.D ICL Reset Factory Settings Status CheckQuick Suffix Selections Dual Interface Programming Notes Dual Interface Programming Instructions Same Code Wand Emulation Selection Code 39 Wand Emulation SelectionRS-232 Selection Laser Emulation Selection Dual Interface Enable/Disable Selection Switched Power Mode SelectionsLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Prefix Selection Primary Interface Suffix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Suffix Selection Secondary Interface Prefix Selection Example 2 Add Suffix for ALL Symbologies Example 1 Add Suffix for Specific SymbologyPrefix and Suffix Examples Example 4 To Clear a Specific Prefix Entry Value Symbology Code Hex Output Delays Selection Beeper Volume Selection Reread Delay Selection Good Read Delay SelectionLaser Voting Selection Code I.D. Transmit Selection Buffered Scans SelectionAIM I.D. Transmit Selection Function Code Transmit Selection Baud Rate Selection CTS Check Selection Parity Selection RS-232 Word Length Selection Serial Wedge Output Selection Protocol Selection ➋ Terminal Type ➎ Editor Command Sequences➌ Code I.D ➍ Length Data Format Editor Require Data Format Move Commands Send CommandsSearch Commands Miscellaneous Commands UPC a with 5 digit addenda Data Formatter Example Scanteam 5700 User’s Guide Introduction AutoTrigger Selection Marker Beam Selection Transmission Rate Selection Wake Up Pulse SelectionOutput Polarity Selection Foreign Keyboard Selection NCR 7052 Keypad Selection AT Direct Connect Selection Keyboard Style Keyboard Style Selections Keyboard Style Selections Keyboard Style Modifiers Code 39 Selections Message Length Codabar Selection Check Character Append Code 39 Selection Minimum Maximum Code 93 Selection Full Ascii Chart Check Digit Interleaved 2 of 5 Selection Matrix 2 of 5 Selection Code 2 of 5 Selection Code 128 Selection Code 11 Selection Code 128 Function Character Selection Code 49 Selection Code 16K Selection Isbn EAN Selection UPC E1 UPC Selection UPC Addenda Selection EAN Addenda Selection Plessey Selection MSI Selection Scanteam 5700 User’s Guide Page Memory Upload Scanteam 5700 User’s Guide Download New Firmware Clone Destination Clone Master+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Keyboard Function Relationships Function Code HEX/ASCII Value Full Ascii Ctrl +Country Codes IBM AT/XT PS/2 Compatibles, IBM XTs Memorex TelexCompatibles Harris Telex IBM, Memorex Ansi Ascii Supported Esprit 200 Bull BDS-7 Wyse WY-60/150 HoneywellHDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only Pin Type D Female 5700-X4 Laser Compatible Bar Image +12VDC Input Wand Emulation RS-232 Laser Output Cleaning the Scan Window Maintenance Replacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Welch Allyn, Inc Obtaining Factory Service Welch Allyn North AmericaEurope Limited Warranty Scanteam 5700 User’s Guide Output Selections Serial Interface Menu Defaults Keyboard Selections General Operating Menu Defaults Codabar Selections Symbology Menu Defaults Industrial Code 11 Selections EAN / UPC Addenda Selections Symbology Menu Defaults Retail Scanteam 5700 User’s Guide Page Page Page Interleaved 2 EANMatrix 2 Code 2