Keyboard Style Selections | Hand Held Products 5700 guide

Keyboard Style Selections

Keyboard Style Selections

Note: The Keyboard Style programming bar codes below apply to the SCANTEAM 5700 software revision level 2.0 or greater.

This programming selection allows you to program special keyboard features, such as Caps Lock and Shift Lock.

Regular is used when you normally have the Caps Lock key off.

Caps Lock is used when you normally have the Caps Lock key on.

Shift Lock is used when you normally have the Shift Lock key on. (Not common to U.S. keyboards.)

Automatic Caps Lock is used if you change the Caps Lock key on and off. The software tracks and reflects if you have Caps Lock on or off (AT and PS/2 only). This selection can only be used with systems that have an LED which notes the Caps Lock status.

Emulate External Keyboard should be scanned if you do not have an external keyboard (IBM AT or equivalent).

✱Regular

Caps Lock

Automatic Caps Lock

Shift Lock

Emulate External Keyboard

SCANTEAM 5700 User’s Guide

3–7

Image 49

Hand Held Products 5700 manual Keyboard Style Selections

Contents

Decoded Output Disclaimer FCC Class B Compliance Statement Scanteam 5700 User’s GuideCanadian Notice A. Statement Patents Table of Contents Require Data Format Data Format Editor Protocol Selection Serial Wedge Output SelectionMarker Beam Selection AutoTrigger Selection Foreign Keyboard Selection Keyboard Function Relationships Supported Interface Keys Industrial Symbology Selections Obtaining Factory Service Technical Support Maintenance Troubleshooting Introduction Scanner Identification Model Number 5X00/A-12 Cable, Keyboard, and Terminal will vary Connecting the Scanner Scanteam 5700/A Scanteam 5700/HD Scanteam 5700ALR IBM PC, Wand Emulation Interface IBM PC AT and Compatibles Interface DefaultIBM PS/2 and Compatibles Interface IBM PC XT and Compatibles Interface Code EAN IBM 4683 InterfaceCode Ocia Interface OCR, RS232 Interface Program Terminal Interface Supported TerminalsTerminal Models Terminal I.D ICL Status Check Reset Factory SettingsQuick Suffix Selections Dual Interface Programming Notes Dual Interface Programming Instructions Same Code Wand Emulation Selection Code 39 Wand Emulation SelectionRS-232 Selection Laser Emulation Selection Switched Power Mode Selections Dual Interface Enable/Disable SelectionLaser Emulation Power Up Delay Selection Introduction Primary Interface Prefix and Suffix Primary Interface Suffix Selection Primary Interface Prefix SelectionExit Selection for Prefix / Suffix Secondary Dual Interface Prefix and Suffix Secondary Interface Suffix Selection Secondary Interface Prefix Selection Example 2 Add Suffix for ALL Symbologies Example 1 Add Suffix for Specific SymbologyPrefix and Suffix Examples Example 4 To Clear a Specific Prefix Entry Value Symbology Code Hex Output Delays Selection Beeper Volume Selection Good Read Delay Selection Reread Delay SelectionLaser Voting Selection Code I.D. Transmit Selection Buffered Scans SelectionAIM I.D. Transmit Selection Function Code Transmit Selection Baud Rate Selection CTS Check Selection Parity Selection RS-232 Word Length Selection Serial Wedge Output Selection Protocol Selection ➋ Terminal Type ➎ Editor Command Sequences➌ Code I.D ➍ Length Data Format Editor Require Data Format Move Commands Send CommandsSearch Commands Miscellaneous Commands UPC a with 5 digit addenda Data Formatter Example Scanteam 5700 User’s Guide Introduction AutoTrigger Selection Marker Beam Selection Wake Up Pulse Selection Transmission Rate SelectionOutput Polarity Selection Foreign Keyboard Selection NCR 7052 Keypad Selection AT Direct Connect Selection Keyboard Style Keyboard Style Selections Keyboard Style Selections Keyboard Style Modifiers Code 39 Selections Message Length Codabar Selection Check Character Append Code 39 Selection Minimum Maximum Code 93 Selection Full Ascii Chart Check Digit Interleaved 2 of 5 Selection Matrix 2 of 5 Selection Code 2 of 5 Selection Code 128 Selection Code 11 Selection Code 128 Function Character Selection Code 49 Selection Code 16K Selection Isbn EAN Selection UPC E1 UPC Selection UPC Addenda Selection EAN Addenda Selection Plessey Selection MSI Selection Scanteam 5700 User’s Guide Page Memory Upload Scanteam 5700 User’s Guide Download New Firmware Clone Master Clone Destination+ a Scanteam 5700 User’s Guide Scanteam 5700 User’s Guide Function Code HEX/ASCII Value Full Ascii Ctrl + Keyboard Function RelationshipsCountry Codes PS/2 Compatibles, IBM XTs Memorex Telex IBM AT/XTCompatibles Harris Telex IBM, Memorex Ansi Ascii Supported Esprit 200 Honeywell Bull BDS-7 Wyse WY-60/150HDS-7 HP 700/92 Keyboards Supported Interface Keys Scanteam 5700 Product Specifications Laser Output only Pin Type D Female 5700-X4 Laser Compatible Bar Image +12VDC Input Wand Emulation RS-232 Laser Output Cleaning the Scan Window Maintenance Replacing the Interface Cable Is the scanner having trouble reading your bar codes? Example You scan 12345 and the host displays A12345B Welch Allyn, Inc Obtaining Factory Service North America Welch AllynEurope Limited Warranty Scanteam 5700 User’s Guide Output Selections Serial Interface Menu Defaults Keyboard Selections General Operating Menu Defaults Codabar Selections Symbology Menu Defaults Industrial Code 11 Selections EAN / UPC Addenda Selections Symbology Menu Defaults Retail Scanteam 5700 User’s Guide Page Page Page Interleaved 2 EANMatrix 2 Code 2