Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000XLS, 6000TR Step Installing the Vent System, A. Vent System Approvals

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Download 48 pages 45.62 Kb

Page 10

Step 3

Step 3

Installing the

Vent System

A. Vent System Approvals

These models are approved to use D-series direct vent pipe components and terminations. Approved vent system components are labeled for identification. NO

OTHER VENTING SYSTEMS OR COMPONENTS MAY BE USED. Detailed installation instructions are included with each vent termination kit and should be used in conjunction with this Installers Guide. The drawing below shows vent system components and terminations.

The flame and ember appearance may vary based on the type of fuel burned and the venting configuration used.

Identifying Vent Components

The vent systems installed on this gas fireplace may include one, two, or three 90° elbow assemblies. The relationships of vertical rise to horizontal run in vent configurations using 90° elbows MUST BE strictly adhered to. The rise to run relationships are shown in the venting drawings and tables. Refer to the diagrams on the next several pages.

NOTE: TWO 45° ELBOWS MAY BE USED IN PLACE OF ONE 90° ELBOW. RISE TO RUN RATIOS IN THE VENT SYSTEM MUST BE FOLLOWED IF 45° ELBOWS ARE USED.

This model has vent starting collars on both the top and the back of the unit. Depending upon the installation, decide which ONE set of starting collars will be used to attach the vent system. The starting collar sealing cap must remain on the starting collar NOT used.

10

VENT SYSTEM COMPONENTS

VENT SYSTEM

TERMINATION KITS

Figure 5. Vent Components and Terminations

Image 10

Heat & Glo LifeStyle 6000XLS manual Step Installing the Vent System, A. Vent System Approvals, Identifying Vent Components

Contents

Installers Guide Models 6000TR 6000XLT-CDN6000ARCH 6000XLSHeat-N-Glo Owners Guide SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Section 4 Maintenance and Servicing TABLE OF CONTENTSSection 3 Installing the Fireplace Section 5 Replacement PartsApprovals and Codes Installation CodesHigh Altitude Installations Approval ListingsIntroducing the Heat-N-Glo Gas Fireplaces Pre-installPreparationGetting Started IF YOU ARE USING THE REAR SET OF VENT COLLARSANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Clearance Requirements Installing the FireplaceStep Locating the Fireplace Figure 3. Fireplace Dimensions, Locations, andMinimum Clearances from the Vent Pipe to Step Framing the FireplaceFigure 4. Framing Dimensions Combustible MaterialsIdentifying Vent Components Step Installing the Vent SystemA. Vent System Approvals Figure 5. Vent Components and TerminationsDV-48D DV-36D DV-90DDV-45D DV-12DFigure 7. Straight Up Vertical Venting STRAIGHT UPVERTICAL VENTING V FT 40 MAX. 12.4 M Kit No Figure 8. Corner InstallationHORIZONTAL VENTING Max. RunVENTING WITH ONE 1 90 ELBOW Figure 9. Venting with One 90 ElbowNOTE MODEL 6000ARCH FOR 6000TR & 6000XLT-CDNVENTING WITH ONE 1 90 ELBOW Figure 10. Venting with One 90 ElbowFigure 11. Venting with Two 90 Elbows VENTING WITH TWO 2 90 ELBOWSH + H1 6000ARCH VENTING WITH TWO 2 90o ELBOWSNOTE MODEL VENTING WITH TWO 2 90o ELBOWSH + H1 + H2 Figure 13. Venting with three 90 elbowsH + H1 VENTING WITH THREE 3 90 ELBOWSNOTE MODEL 6000ARCH VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbowsVenting Out the Top Vent B. Installing Vent Components For Model 6000TRVenting Out the Rear Vent Figure 15 For Model 6000TR1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components Model DVK-01TRDdoes not need an exterior Figure 19. Installing Support Brackets4. Install Firestops firestop on an exterior combustible wallFigure 20. 12 x 12 Hole and Vent Pipe Figure 22. 11 x 11 Hole and New Framing Members Figure 23. Ceiling Firestop Ceiling SideC. Vent Termination Figure 24. Attic FirestopFigure 25. Round & Trapezoid Termination Caps TERMINATION CAPS Figure 26. Vent Termination Minimum ClearancesIF EXTERIOR WALLS ARE FINISHED WITH =VENT TERMINALMAJOR U.S. BUILDING CODES SPECI THE INTEREST OF SAFETY. SEE THEFOLLOWING DIAGRAM FOR MINIMUM FY MINIMUM CHIMNEY AND/OR VENTRoof Pitch Step The Gas Control Systems Step Positioning Leveling, and Securing theFireplace Figure 28. Proper Positioning, Leveling, andStep The Gas Supply Line Figure 29. Gas Controls SystemsPressure Step Gas Pressure RequirementsFigure 30. Gas Supply Line Natural GasStep Wiring theFor Standing Pilot Ignition Wiring Optional AccessoriesOptional Accessories For Direct Spark Ignition DSI WiringFigure 32. Fan Wiring Diagram Remote Wall Switchis found on model Step FinishingThe microswitch 6000ARCH onlyInstalling the Trim Step Installing Trim Logs, and Ember MaterialHearth Extensions Figure 35. Sealant MaterialPositioning the Logs Placing the Ember Material1.Lift the trim door up and out of the unit Figure 37. Model 6000TR Glass AssemblyFigure 38. Placement of the Ember Material 1.Lift the top trim door up and out of the unitReview safety warnings and cautions Step Before Lighting the Fireplace StepLighting the Fireplace Double-checkfor faulty componentsStep Heating Control InstallationAfter the Step 14 Relief Ports Model 6000ARCHTURN OFF THE GAS BEFORE SERVICING Fireplace MaintenanceMaintaining and Servicing Your Fireplace YOUR FIREPLACEFigure 41. Burner Flame Patterns Figure 42. Pilot/Ignitor Flame PatternsPART Replacement Parts and AccessoriesStanding Pilot with Robertshaw Controls only PART DESCRIPTIONPART DESCRIPTION Standing Pilot with S.I.T. controls onlyPART PART NUMBERPART DSI Ignition OnlyBoth Standing Pilot and DSI Ignition PART DESCRIPTION6000TR Both Standing Pilot and DSI Ignition ContGLASS SPECIFICATIONS 22” X 34”PART DESCRIPTION AccessoriesACCESSORY PART NUMBER