Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000XLT-CDN, 6000TR VENTING WITH THREE 3 90 ELBOWS, NOTE MODEL 6000ARCH

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Page 19

VENTING WITH THREE (3) 90° ELBOWS

V (FT.)	H (FT.)
1' MIN. (305mm)	5' MAX. (1.52m)
2' MIN. (610mm)	10' MAX. (3.1m)
3' MIN. (914mm)	15' MAX. (4.65m)
4' MIN. (1.22m)	20' MAX. (6.2m)

NOTE: H + H1 = 20' MAX. (6.2m)

V + V1 + H + H1= 40' MAX. (12.4m)

VENTING WITH THREE (3) 90° ELBOWS

V (FT.)	H + H1 (FT.)
1' MIN.(305mm)	5' MAX. (1.52m)
2' MIN. (610mm)	10' MAX. (3.1m)
3' MIN. (914mm)	15' MAX. (4.65m)
4' MIN. (1.22m)	20' MAX. (6.2m)

H + H1 = 20' MAX. (6.2m)

NOTE: V+V1+H+H1 = 40' MAX. (12.4m)

NOTE: MODEL 6000ARCH

A 12-inch length of straight vent pipe MUST be the first vent component at- tached to the unit.

Figure 14. Venting with three 90° elbows	19

Page 19

Image 19

Heat & Glo LifeStyle 6000XLT-CDN VENTING WITH THREE 3 90 ELBOWS, NOTE MODEL 6000ARCH, Venting with three 90 elbows

Contents

Installers Guide Models 6000TR 6000XLT-CDN6000ARCH 6000XLSHeat-N-Glo Owners Guide SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Section 5 Replacement Parts TABLE OF CONTENTSSection 3 Installing the Fireplace Section 4 Maintenance and ServicingApproval Listings Installation CodesHigh Altitude Installations Approvals and CodesIF YOU ARE USING THE REAR SET OF VENT COLLARS Pre-installPreparationGetting Started Introducing the Heat-N-Glo Gas FireplacesANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Figure 3. Fireplace Dimensions, Locations, and Installing the FireplaceStep Locating the Fireplace Clearance RequirementsCombustible Materials Step Framing the FireplaceFigure 4. Framing Dimensions Minimum Clearances from the Vent Pipe toFigure 5. Vent Components and Terminations Step Installing the Vent SystemA. Vent System Approvals Identifying Vent ComponentsDV-12D DV-90DDV-45D DV-48D DV-36DFigure 7. Straight Up Vertical Venting STRAIGHT UPVERTICAL VENTING V FT 40 MAX. 12.4 M Max. Run Figure 8. Corner InstallationHORIZONTAL VENTING Kit NoFigure 9. Venting with One 90 Elbow VENTING WITH ONE 1 90 ELBOWFigure 10. Venting with One 90 Elbow FOR 6000TR & 6000XLT-CDNVENTING WITH ONE 1 90 ELBOW NOTE MODEL 6000ARCHFigure 11. Venting with Two 90 Elbows VENTING WITH TWO 2 90 ELBOWSH + H1 VENTING WITH TWO 2 90o ELBOWS VENTING WITH TWO 2 90o ELBOWSNOTE MODEL 6000ARCHVENTING WITH THREE 3 90 ELBOWS Figure 13. Venting with three 90 elbowsH + H1 H + H1 + H2Figure 14. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS NOTE MODEL 6000ARCHFigure 15 For Model 6000TR B. Installing Vent Components For Model 6000TRVenting Out the Rear Vent Venting Out the Top Vent1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components firestop on an exterior combustible wall Figure 19. Installing Support Brackets4. Install Firestops Model DVK-01TRDdoes not need an exteriorFigure 20. 12 x 12 Hole and Vent Pipe Figure 23. Ceiling Firestop Ceiling Side Figure 22. 11 x 11 Hole and New Framing MembersFigure 24. Attic Firestop C. Vent TerminationFigure 25. Round & Trapezoid Termination Caps =VENT TERMINAL Figure 26. Vent Termination Minimum ClearancesIF EXTERIOR WALLS ARE FINISHED WITH TERMINATION CAPSFY MINIMUM CHIMNEY AND/OR VENT THE INTEREST OF SAFETY. SEE THEFOLLOWING DIAGRAM FOR MINIMUM MAJOR U.S. BUILDING CODES SPECIRoof Pitch Figure 28. Proper Positioning, Leveling, and Step Positioning Leveling, and Securing theFireplace Step The Gas Control SystemsFigure 29. Gas Controls Systems Step The Gas Supply LineNatural Gas Step Gas Pressure RequirementsFigure 30. Gas Supply Line PressureOptional Accessories Wiring theFor Standing Pilot Ignition Wiring StepRemote Wall Switch For Direct Spark Ignition DSI WiringFigure 32. Fan Wiring Diagram Optional Accessories6000ARCH only Step FinishingThe microswitch is found on modelFigure 35. Sealant Material Step Installing Trim Logs, and Ember MaterialHearth Extensions Installing the TrimPlacing the Ember Material Positioning the Logs1.Lift the top trim door up and out of the unit Figure 37. Model 6000TR Glass AssemblyFigure 38. Placement of the Ember Material 1.Lift the trim door up and out of the unitDouble-checkfor faulty components Step Before Lighting the Fireplace StepLighting the Fireplace Review safety warnings and cautionsStep 14 Relief Ports Model 6000ARCH InstallationAfter the Step Heating ControlYOUR FIREPLACE Fireplace MaintenanceMaintaining and Servicing Your Fireplace TURN OFF THE GAS BEFORE SERVICINGFigure 42. Pilot/Ignitor Flame Patterns Figure 41. Burner Flame PatternsPART DESCRIPTION Replacement Parts and AccessoriesStanding Pilot with Robertshaw Controls only PARTPART NUMBER Standing Pilot with S.I.T. controls onlyPART PART DESCRIPTIONPART DESCRIPTION DSI Ignition OnlyBoth Standing Pilot and DSI Ignition PART22” X 34” Both Standing Pilot and DSI Ignition ContGLASS SPECIFICATIONS 6000TRPART NUMBER AccessoriesACCESSORY PART DESCRIPTION

VENTING WITH THREE (3) 90° ELBOWS

Figure 14. Venting with three 90° elbows