Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000XLS Step, Wiring the, For Standing Pilot Ignition Wiring, Fireplace

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Download 48 pages 45.62 Kb

Page 34

Step 8

34

Step 8	NOTE: Electrical wiring must be installed by a
Wiring the	licensed electrician.
Fireplace	Caution: Disconnect remote controls if you are
	absent for extended time periods. This will
	prevent accidental fireplace operation.

For Standing Pilot Ignition Wiring

Appliance Requirements

•This appliance DOES NOT require 110-120 VAC to operate.

!WARNING

DO NOT CONNECT 110-120 VAC TO THE GAS CONTROL VALVE OR THE APPLIANCE WILL MALFUNCTION AND THE VALVE WILL BE DESTROYED.

Optional Accessories

Optional fan and remote control kits require that 110- 120 VAC be wired to the factory installed junction box before the fireplace is permanently installed.

Remote Wall Switch

Position the remote wall switch in the desired position on a wall. Run a maximum of 25 feet (7.8 m) or less length of 18 A.W.G. minimum wire and connect it to the fireplace ON/OFF switch pigtails.

!WARNING

DO NOT CONNECT 110-120 VAC TO THE REMOTE WALL SWITCH OR THE CONTROL VALVE WILL BE DESTROYED.

CAUTION	LABEL ALL WIRES PRIOR TO DISCONNECTION
	WHEN SERVICING CONTROLS. WIRING
	ERRORS CAN CAUSE IMPROPER AND
	DANGEROUS OPERATION. VERIFY PROPER
	OPERATION AFTER SERVICING.

NOTE: 6000XLT-CDN DOES NOT HAVE A LIMIT SWITCH.

Figure 31. Standing Pilot Ignition Wiring Diagram

Image 34

Heat & Glo LifeStyle 6000XLS, 6000TR Step, Wiring the, For Standing Pilot Ignition Wiring, Fireplace, licensed electrician

Contents

Installers Guide Models 6000TR 6000XLT-CDN6000ARCH 6000XLSHeat-N-Glo Owners Guide SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Section 4 Maintenance and Servicing TABLE OF CONTENTSSection 3 Installing the Fireplace Section 5 Replacement PartsApprovals and Codes Installation CodesHigh Altitude Installations Approval ListingsIntroducing the Heat-N-Glo Gas Fireplaces Pre-installPreparationGetting Started IF YOU ARE USING THE REAR SET OF VENT COLLARSANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Clearance Requirements Installing the FireplaceStep Locating the Fireplace Figure 3. Fireplace Dimensions, Locations, andMinimum Clearances from the Vent Pipe to Step Framing the FireplaceFigure 4. Framing Dimensions Combustible MaterialsIdentifying Vent Components Step Installing the Vent SystemA. Vent System Approvals Figure 5. Vent Components and TerminationsDV-48D DV-36D DV-90DDV-45D DV-12DFigure 7. Straight Up Vertical Venting STRAIGHT UPVERTICAL VENTING V FT 40 MAX. 12.4 M Kit No Figure 8. Corner InstallationHORIZONTAL VENTING Max. RunVENTING WITH ONE 1 90 ELBOW Figure 9. Venting with One 90 ElbowNOTE MODEL 6000ARCH FOR 6000TR & 6000XLT-CDNVENTING WITH ONE 1 90 ELBOW Figure 10. Venting with One 90 ElbowFigure 11. Venting with Two 90 Elbows VENTING WITH TWO 2 90 ELBOWSH + H1 6000ARCH VENTING WITH TWO 2 90o ELBOWSNOTE MODEL VENTING WITH TWO 2 90o ELBOWSH + H1 + H2 Figure 13. Venting with three 90 elbowsH + H1 VENTING WITH THREE 3 90 ELBOWSNOTE MODEL 6000ARCH VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbowsVenting Out the Top Vent B. Installing Vent Components For Model 6000TRVenting Out the Rear Vent Figure 15 For Model 6000TR1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components Model DVK-01TRDdoes not need an exterior Figure 19. Installing Support Brackets4. Install Firestops firestop on an exterior combustible wallFigure 20. 12 x 12 Hole and Vent Pipe Figure 22. 11 x 11 Hole and New Framing Members Figure 23. Ceiling Firestop Ceiling SideC. Vent Termination Figure 24. Attic FirestopFigure 25. Round & Trapezoid Termination Caps TERMINATION CAPS Figure 26. Vent Termination Minimum ClearancesIF EXTERIOR WALLS ARE FINISHED WITH =VENT TERMINALMAJOR U.S. BUILDING CODES SPECI THE INTEREST OF SAFETY. SEE THEFOLLOWING DIAGRAM FOR MINIMUM FY MINIMUM CHIMNEY AND/OR VENTRoof Pitch Step The Gas Control Systems Step Positioning Leveling, and Securing theFireplace Figure 28. Proper Positioning, Leveling, andStep The Gas Supply Line Figure 29. Gas Controls SystemsPressure Step Gas Pressure RequirementsFigure 30. Gas Supply Line Natural GasStep Wiring theFor Standing Pilot Ignition Wiring Optional AccessoriesOptional Accessories For Direct Spark Ignition DSI WiringFigure 32. Fan Wiring Diagram Remote Wall Switchis found on model Step FinishingThe microswitch 6000ARCH onlyInstalling the Trim Step Installing Trim Logs, and Ember MaterialHearth Extensions Figure 35. Sealant MaterialPositioning the Logs Placing the Ember Material1.Lift the trim door up and out of the unit Figure 37. Model 6000TR Glass AssemblyFigure 38. Placement of the Ember Material 1.Lift the top trim door up and out of the unitReview safety warnings and cautions Step Before Lighting the Fireplace StepLighting the Fireplace Double-checkfor faulty componentsStep Heating Control InstallationAfter the Step 14 Relief Ports Model 6000ARCHTURN OFF THE GAS BEFORE SERVICING Fireplace MaintenanceMaintaining and Servicing Your Fireplace YOUR FIREPLACEFigure 41. Burner Flame Patterns Figure 42. Pilot/Ignitor Flame PatternsPART Replacement Parts and AccessoriesStanding Pilot with Robertshaw Controls only PART DESCRIPTIONPART DESCRIPTION Standing Pilot with S.I.T. controls onlyPART PART NUMBERPART DSI Ignition OnlyBoth Standing Pilot and DSI Ignition PART DESCRIPTION6000TR Both Standing Pilot and DSI Ignition ContGLASS SPECIFICATIONS 22” X 34”PART DESCRIPTION AccessoriesACCESSORY PART NUMBER