Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000ARCH, 6000XLT-CDN Step Positioning Leveling, and Securing the, Fireplace

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Download 48 pages 45.62 Kb

Page 31

Step 4

Step 4

Positioning,

Leveling, and

Securing the

Fireplace

1.Place the fireplace into position.

2.Level the fireplace from side to side and from front to back.

3.Shim the fireplace with non-combus- tible material, such as sheet metal, as necessary.

4.Secure the fireplace to the framing by nailing or screwing

Step 5

The Gas Control

Systems

The diagram below shows how to properly position, level, and secure the fireplace.

Figure 28. Proper Positioning, Leveling, and

Securing of a Fireplace

!WARNING: THIS UNIT IS NOT FOR USE WITH SOLID FUEL.

Two types of gas control systems are used with these models: Standing Pilot Ignition and Direct Spark Ignition (DSI). Models 6000XLT-CDN and 6000XLS have Standing Pilot Ignition only. Model 6000ARCH has DSI only. Model 6000TR has both Standing Pilot and DSI systems

Standing Pilot Ignition System

This system includes millivolt control valve, standing pilot, thermopile/thermocouple flame sensor, and piezo ignitor.

!WARNING: 110-120 VAC MUST NEVER BE CONNECTED TO A CONTROL VALVE IN A MILLIVOLT SYSTEM.

Direct Spark Ignition (DSI) System

This system includes a 110V control valve, electronic module, and spark ignitor/flame sensor.

!WARNING: CONTINUOUS 110-120 VAC SERVICE MUST BE WIRED DIRECTLY TO THE FIREPLACE JUNCTION BOX IN A DSI SYSTEM.

!WARNING: DIRECT VENT PROPANE MODELS WITH DSI CONTROL SYSTEMS CANNOT BE USED IN

31

Image 31

Heat & Glo LifeStyle 6000ARCH, 6000TR Step Positioning Leveling, and Securing the, Fireplace, Step The Gas Control Systems

Contents

Installers Guide Models 6000TR 6000XLT-CDN6000ARCH 6000XLSHeat-N-Glo Owners Guide SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Section 5 Replacement Parts TABLE OF CONTENTSSection 3 Installing the Fireplace Section 4 Maintenance and ServicingApproval Listings Installation CodesHigh Altitude Installations Approvals and CodesIF YOU ARE USING THE REAR SET OF VENT COLLARS Pre-installPreparationGetting Started Introducing the Heat-N-Glo Gas FireplacesANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Figure 3. Fireplace Dimensions, Locations, and Installing the FireplaceStep Locating the Fireplace Clearance RequirementsCombustible Materials Step Framing the FireplaceFigure 4. Framing Dimensions Minimum Clearances from the Vent Pipe toFigure 5. Vent Components and Terminations Step Installing the Vent SystemA. Vent System Approvals Identifying Vent ComponentsDV-12D DV-90DDV-45D DV-48D DV-36DFigure 7. Straight Up Vertical Venting STRAIGHT UPVERTICAL VENTING V FT 40 MAX. 12.4 M Max. Run Figure 8. Corner InstallationHORIZONTAL VENTING Kit NoFigure 9. Venting with One 90 Elbow VENTING WITH ONE 1 90 ELBOWFigure 10. Venting with One 90 Elbow FOR 6000TR & 6000XLT-CDNVENTING WITH ONE 1 90 ELBOW NOTE MODEL 6000ARCHFigure 11. Venting with Two 90 Elbows VENTING WITH TWO 2 90 ELBOWSH + H1 VENTING WITH TWO 2 90o ELBOWS VENTING WITH TWO 2 90o ELBOWSNOTE MODEL 6000ARCHVENTING WITH THREE 3 90 ELBOWS Figure 13. Venting with three 90 elbowsH + H1 H + H1 + H2Figure 14. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS NOTE MODEL 6000ARCHFigure 15 For Model 6000TR B. Installing Vent Components For Model 6000TRVenting Out the Rear Vent Venting Out the Top Vent1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components firestop on an exterior combustible wall Figure 19. Installing Support Brackets4. Install Firestops Model DVK-01TRDdoes not need an exteriorFigure 20. 12 x 12 Hole and Vent Pipe Figure 23. Ceiling Firestop Ceiling Side Figure 22. 11 x 11 Hole and New Framing MembersFigure 24. Attic Firestop C. Vent TerminationFigure 25. Round & Trapezoid Termination Caps =VENT TERMINAL Figure 26. Vent Termination Minimum ClearancesIF EXTERIOR WALLS ARE FINISHED WITH TERMINATION CAPSFY MINIMUM CHIMNEY AND/OR VENT THE INTEREST OF SAFETY. SEE THEFOLLOWING DIAGRAM FOR MINIMUM MAJOR U.S. BUILDING CODES SPECIRoof Pitch Figure 28. Proper Positioning, Leveling, and Step Positioning Leveling, and Securing theFireplace Step The Gas Control SystemsFigure 29. Gas Controls Systems Step The Gas Supply LineNatural Gas Step Gas Pressure RequirementsFigure 30. Gas Supply Line PressureOptional Accessories Wiring theFor Standing Pilot Ignition Wiring StepRemote Wall Switch For Direct Spark Ignition DSI WiringFigure 32. Fan Wiring Diagram Optional Accessories6000ARCH only Step FinishingThe microswitch is found on modelFigure 35. Sealant Material Step Installing Trim Logs, and Ember MaterialHearth Extensions Installing the TrimPlacing the Ember Material Positioning the Logs1.Lift the top trim door up and out of the unit Figure 37. Model 6000TR Glass AssemblyFigure 38. Placement of the Ember Material 1.Lift the trim door up and out of the unitDouble-checkfor faulty components Step Before Lighting the Fireplace StepLighting the Fireplace Review safety warnings and cautionsStep 14 Relief Ports Model 6000ARCH InstallationAfter the Step Heating ControlYOUR FIREPLACE Fireplace MaintenanceMaintaining and Servicing Your Fireplace TURN OFF THE GAS BEFORE SERVICINGFigure 42. Pilot/Ignitor Flame Patterns Figure 41. Burner Flame PatternsPART DESCRIPTION Replacement Parts and AccessoriesStanding Pilot with Robertshaw Controls only PARTPART NUMBER Standing Pilot with S.I.T. controls onlyPART PART DESCRIPTIONPART DESCRIPTION DSI Ignition OnlyBoth Standing Pilot and DSI Ignition PART22” X 34” Both Standing Pilot and DSI Ignition ContGLASS SPECIFICATIONS 6000TRPART NUMBER AccessoriesACCESSORY PART DESCRIPTION