Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000XLT-CDN VENTING WITH TWO 2 90 ELBOWS, Venting with Two 90 Elbows, H + H1

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Page 16

VENTING WITH TWO (2) 90° ELBOWS
V	H		H + H1
1´ MIN. (305 mm)	2´ MAX. (610 mm)		5´ MAX. (1.52m)
2´ MIN. (610 mm)	4´ MAX. (1.22 m)		10´ MAX. (3.1m)
3´ MIN. (914 mm)	6´ MAX. (1.86 m)		15´ MAX. (4.65m)
4´ MIN. (1.22 m)	8´ MAX. (2.48 m)		20´ MAX. (6.2m)
V+H+H1 = 40´ MAX. (12.4 m)		H = 8´ MAX. (2.48 m)	H+H1 = 20´ MAX. (6.2m)

Figure 11. Venting with Two 90° Elbows

Page 16

Image 16

Heat & Glo LifeStyle 6000XLT-CDN, 6000TR, 6000XLS, 6000ARCH VENTING WITH TWO 2 90 ELBOWS, Venting with Two 90 Elbows, H + H1

Contents

Installers Guide Models 6000TR 6000XLT-CDN6000ARCH 6000XLSHeat-N-Glo Owners Guide SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL TABLE OF CONTENTS Section 3 Installing the FireplaceSection 4 Maintenance and Servicing Section 5 Replacement PartsInstallation Codes High Altitude InstallationsApprovals and Codes Approval ListingsPre-installPreparation Getting StartedIntroducing the Heat-N-Glo Gas Fireplaces IF YOU ARE USING THE REAR SET OF VENT COLLARSANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Installing the Fireplace Step Locating the FireplaceClearance Requirements Figure 3. Fireplace Dimensions, Locations, andStep Framing the Fireplace Figure 4. Framing DimensionsMinimum Clearances from the Vent Pipe to Combustible MaterialsStep Installing the Vent System A. Vent System ApprovalsIdentifying Vent Components Figure 5. Vent Components and TerminationsDV-90D DV-45DDV-48D DV-36D DV-12DFigure 7. Straight Up Vertical Venting STRAIGHT UPVERTICAL VENTING V FT 40 MAX. 12.4 M Figure 8. Corner Installation HORIZONTAL VENTINGKit No Max. RunVENTING WITH ONE 1 90 ELBOW Figure 9. Venting with One 90 ElbowFOR 6000TR & 6000XLT-CDN VENTING WITH ONE 1 90 ELBOWNOTE MODEL 6000ARCH Figure 10. Venting with One 90 ElbowFigure 11. Venting with Two 90 Elbows VENTING WITH TWO 2 90 ELBOWSH + H1 VENTING WITH TWO 2 90o ELBOWS NOTE MODEL6000ARCH VENTING WITH TWO 2 90o ELBOWSFigure 13. Venting with three 90 elbows H + H1H + H1 + H2 VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS VENTING WITH THREE 3 90 ELBOWSNOTE MODEL 6000ARCH Figure 14. Venting with three 90 elbowsB. Installing Vent Components For Model 6000TR Venting Out the Rear VentVenting Out the Top Vent Figure 15 For Model 6000TR1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components Figure 19. Installing Support Brackets 4. Install FirestopsModel DVK-01TRDdoes not need an exterior firestop on an exterior combustible wallFigure 20. 12 x 12 Hole and Vent Pipe Figure 22. 11 x 11 Hole and New Framing Members Figure 23. Ceiling Firestop Ceiling SideC. Vent Termination Figure 24. Attic FirestopFigure 25. Round & Trapezoid Termination Caps Figure 26. Vent Termination Minimum Clearances IF EXTERIOR WALLS ARE FINISHED WITHTERMINATION CAPS =VENT TERMINALTHE INTEREST OF SAFETY. SEE THE FOLLOWING DIAGRAM FOR MINIMUMMAJOR U.S. BUILDING CODES SPECI FY MINIMUM CHIMNEY AND/OR VENTRoof Pitch Step Positioning Leveling, and Securing the FireplaceStep The Gas Control Systems Figure 28. Proper Positioning, Leveling, andStep The Gas Supply Line Figure 29. Gas Controls SystemsStep Gas Pressure Requirements Figure 30. Gas Supply LinePressure Natural GasWiring the For Standing Pilot Ignition WiringStep Optional AccessoriesFor Direct Spark Ignition DSI Wiring Figure 32. Fan Wiring DiagramOptional Accessories Remote Wall SwitchStep Finishing The microswitchis found on model 6000ARCH onlyStep Installing Trim Logs, and Ember Material Hearth ExtensionsInstalling the Trim Figure 35. Sealant MaterialPositioning the Logs Placing the Ember MaterialFigure 37. Model 6000TR Glass Assembly Figure 38. Placement of the Ember Material1.Lift the trim door up and out of the unit 1.Lift the top trim door up and out of the unitStep Before Lighting the Fireplace Step Lighting the FireplaceReview safety warnings and cautions Double-checkfor faulty componentsInstallation After theStep Heating Control Step 14 Relief Ports Model 6000ARCHFireplace Maintenance Maintaining and Servicing Your FireplaceTURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACEFigure 41. Burner Flame Patterns Figure 42. Pilot/Ignitor Flame PatternsReplacement Parts and Accessories Standing Pilot with Robertshaw Controls onlyPART PART DESCRIPTIONStanding Pilot with S.I.T. controls only PARTPART DESCRIPTION PART NUMBERDSI Ignition Only Both Standing Pilot and DSI IgnitionPART PART DESCRIPTIONBoth Standing Pilot and DSI Ignition Cont GLASS SPECIFICATIONS6000TR 22” X 34”Accessories ACCESSORYPART DESCRIPTION PART NUMBER

VENTING WITH TWO (2) 90° ELBOWS

H + H1

Figure 11. Venting with Two 90° Elbows