Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000TR, 6000XLT-CDN manual VENTING WITH TWO 2 90o ELBOWS, Note Model, 6000ARCH

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Page 17

VENTING WITH TWO (2) 90o ELBOWS
V (FT.)		H + H1 (FT.)
1' MIN.	(305mm)	5´ MAX. (1.52m)
2' MIN.	(610mm)	10´ MAX. (3.1m)
3' MIN.	(914mm)	15´ MAX. (4.65m)
4' MIN.	(1.22m)	20´ MAX. (6.2m)
V+H+H1= 40' MAX.(12.4m)		H+H1= 20´ MAX. (6.2m)
NOTE: MODEL
6000ARCH
A 12-inch length
of straight vent
pipe MUST be
the first vent
component
attached to
the unit.
VENTING WITH TWO (2) 90o ELBOWS
V (FT.)		H (FT.)
1' MIN.	(305mm)	5´ MAX. (1.52m)
2' MIN.	(610mm)	10´ MAX. (3.1m)
3' MIN.	(914mm)	15´ MAX. (4.65m)
4' MIN.	(1.22m)	20´ MAX. (6.2m)
		H = 20´ MAX. (6.2m)
V+V1+H= 40' MAX.(12.4m)

Figure 12. Venting with Two 90° Elbows

Page 17

Image 17

Heat & Glo LifeStyle 6000TR, 6000XLT-CDN VENTING WITH TWO 2 90o ELBOWS, Note Model, 6000ARCH, Venting with Two 90 Elbows

Contents

Heat-N-Glo Models 6000TR 6000XLT-CDN6000ARCH 6000XLSInstallers Guide THIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONOwners Guide Section 3 Installing the Fireplace TABLE OF CONTENTSSection 4 Maintenance and Servicing Section 5 Replacement PartsHigh Altitude Installations Installation CodesApprovals and Codes Approval ListingsGetting Started Pre-installPreparationIntroducing the Heat-N-Glo Gas Fireplaces IF YOU ARE USING THE REAR SET OF VENT COLLARSANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Step Locating the Fireplace Installing the FireplaceClearance Requirements Figure 3. Fireplace Dimensions, Locations, andFigure 4. Framing Dimensions Step Framing the FireplaceMinimum Clearances from the Vent Pipe to Combustible MaterialsA. Vent System Approvals Step Installing the Vent SystemIdentifying Vent Components Figure 5. Vent Components and TerminationsDV-45D DV-90DDV-48D DV-36D DV-12DVERTICAL VENTING V FT 40 MAX. 12.4 M STRAIGHT UPFigure 7. Straight Up Vertical Venting HORIZONTAL VENTING Figure 8. Corner InstallationKit No Max. RunFigure 9. Venting with One 90 Elbow VENTING WITH ONE 1 90 ELBOWVENTING WITH ONE 1 90 ELBOW FOR 6000TR & 6000XLT-CDNNOTE MODEL 6000ARCH Figure 10. Venting with One 90 ElbowH + H1 VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with Two 90 Elbows NOTE MODEL VENTING WITH TWO 2 90o ELBOWS6000ARCH VENTING WITH TWO 2 90o ELBOWSH + H1 Figure 13. Venting with three 90 elbowsH + H1 + H2 VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS VENTING WITH THREE 3 90 ELBOWSNOTE MODEL 6000ARCH Figure 14. Venting with three 90 elbowsVenting Out the Rear Vent B. Installing Vent Components For Model 6000TRVenting Out the Top Vent Figure 15 For Model 6000TR1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components 4. Install Firestops Figure 19. Installing Support BracketsModel DVK-01TRDdoes not need an exterior firestop on an exterior combustible wallFigure 20. 12 x 12 Hole and Vent Pipe Figure 23. Ceiling Firestop Ceiling Side Figure 22. 11 x 11 Hole and New Framing MembersFigure 24. Attic Firestop C. Vent TerminationFigure 25. Round & Trapezoid Termination Caps IF EXTERIOR WALLS ARE FINISHED WITH Figure 26. Vent Termination Minimum ClearancesTERMINATION CAPS =VENT TERMINALFOLLOWING DIAGRAM FOR MINIMUM THE INTEREST OF SAFETY. SEE THEMAJOR U.S. BUILDING CODES SPECI FY MINIMUM CHIMNEY AND/OR VENTRoof Pitch Fireplace Step Positioning Leveling, and Securing theStep The Gas Control Systems Figure 28. Proper Positioning, Leveling, andFigure 29. Gas Controls Systems Step The Gas Supply LineFigure 30. Gas Supply Line Step Gas Pressure RequirementsPressure Natural GasFor Standing Pilot Ignition Wiring Wiring theStep Optional AccessoriesFigure 32. Fan Wiring Diagram For Direct Spark Ignition DSI WiringOptional Accessories Remote Wall SwitchThe microswitch Step Finishingis found on model 6000ARCH onlyHearth Extensions Step Installing Trim Logs, and Ember MaterialInstalling the Trim Figure 35. Sealant MaterialPlacing the Ember Material Positioning the LogsFigure 38. Placement of the Ember Material Figure 37. Model 6000TR Glass Assembly1.Lift the trim door up and out of the unit 1.Lift the top trim door up and out of the unitLighting the Fireplace Step Before Lighting the Fireplace StepReview safety warnings and cautions Double-checkfor faulty componentsAfter the InstallationStep Heating Control Step 14 Relief Ports Model 6000ARCHMaintaining and Servicing Your Fireplace Fireplace MaintenanceTURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACEFigure 42. Pilot/Ignitor Flame Patterns Figure 41. Burner Flame PatternsStanding Pilot with Robertshaw Controls only Replacement Parts and AccessoriesPART PART DESCRIPTIONPART Standing Pilot with S.I.T. controls onlyPART DESCRIPTION PART NUMBERBoth Standing Pilot and DSI Ignition DSI Ignition OnlyPART PART DESCRIPTIONGLASS SPECIFICATIONS Both Standing Pilot and DSI Ignition Cont6000TR 22” X 34”ACCESSORY AccessoriesPART DESCRIPTION PART NUMBER

VENTING WITH TWO (2) 90o ELBOWS

NOTE: MODEL

6000ARCH

Figure 12. Venting with Two 90° Elbows