Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000TR 11 x 11 Hole and New Framing Members, Ceiling Firestop Ceiling Side

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Download 48 pages 45.62 Kb

Page 25

Image 25

Figure 22. 11" x 11" Hole and New Framing Members

1.Cut the 11-inch by 11-inch hole.

2.Add the new framing members.

This shows a ceiling installation.

•Drill a hole or drive a nail through this centerpoint.

•Check the floor above for any obstructions, such as wiring or plumbing runs.

•Reposition the fireplace and vent system, if neces- sary, to accommodate the ceiling joists and/or obstructions.

•Cut an 11-inch X 11-inch (280 mm X 280 mm) hole through the ceiling, using the centerpoint previously marked.

•Frame the hole with framing lumber the same size as the ceiling joists.

Figure 22. 11" x 11" Hole and New Framing Members

If the area above the ceiling is NOT an attic, position and secure the ceiling firestop on the ceiling side of the previously cut and framed hole.

JOIST

CEILING

NAILS (4 REQUIRED)

CEILING FIRESTOP

Figure 23. Ceiling Firestop (Ceiling Side)

Page 25

Image 25

Heat & Glo LifeStyle 6000TR, 6000XLT-CDN, 6000XLS manual 11 x 11 Hole and New Framing Members, Ceiling Firestop Ceiling Side

Contents

Installers Guide Models 6000TR 6000XLT-CDN6000ARCH 6000XLSHeat-N-Glo Owners Guide SAFETY AND WARNING INFORMATIONTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Section 3 Installing the Fireplace TABLE OF CONTENTSSection 4 Maintenance and Servicing Section 5 Replacement PartsHigh Altitude Installations Installation CodesApprovals and Codes Approval ListingsGetting Started Pre-installPreparationIntroducing the Heat-N-Glo Gas Fireplaces IF YOU ARE USING THE REAR SET OF VENT COLLARSANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Step Locating the Fireplace Installing the FireplaceClearance Requirements Figure 3. Fireplace Dimensions, Locations, andFigure 4. Framing Dimensions Step Framing the FireplaceMinimum Clearances from the Vent Pipe to Combustible MaterialsA. Vent System Approvals Step Installing the Vent SystemIdentifying Vent Components Figure 5. Vent Components and TerminationsDV-45D DV-90DDV-48D DV-36D DV-12DFigure 7. Straight Up Vertical Venting STRAIGHT UPVERTICAL VENTING V FT 40 MAX. 12.4 M HORIZONTAL VENTING Figure 8. Corner InstallationKit No Max. RunFigure 9. Venting with One 90 Elbow VENTING WITH ONE 1 90 ELBOWVENTING WITH ONE 1 90 ELBOW FOR 6000TR & 6000XLT-CDNNOTE MODEL 6000ARCH Figure 10. Venting with One 90 ElbowFigure 11. Venting with Two 90 Elbows VENTING WITH TWO 2 90 ELBOWSH + H1 NOTE MODEL VENTING WITH TWO 2 90o ELBOWS6000ARCH VENTING WITH TWO 2 90o ELBOWSH + H1 Figure 13. Venting with three 90 elbowsH + H1 + H2 VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS VENTING WITH THREE 3 90 ELBOWSNOTE MODEL 6000ARCH Figure 14. Venting with three 90 elbowsVenting Out the Rear Vent B. Installing Vent Components For Model 6000TRVenting Out the Top Vent Figure 15 For Model 6000TR1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components 4. Install Firestops Figure 19. Installing Support BracketsModel DVK-01TRDdoes not need an exterior firestop on an exterior combustible wallFigure 20. 12 x 12 Hole and Vent Pipe Figure 23. Ceiling Firestop Ceiling Side Figure 22. 11 x 11 Hole and New Framing MembersFigure 24. Attic Firestop C. Vent TerminationFigure 25. Round & Trapezoid Termination Caps IF EXTERIOR WALLS ARE FINISHED WITH Figure 26. Vent Termination Minimum ClearancesTERMINATION CAPS =VENT TERMINALFOLLOWING DIAGRAM FOR MINIMUM THE INTEREST OF SAFETY. SEE THEMAJOR U.S. BUILDING CODES SPECI FY MINIMUM CHIMNEY AND/OR VENTRoof Pitch Fireplace Step Positioning Leveling, and Securing theStep The Gas Control Systems Figure 28. Proper Positioning, Leveling, andFigure 29. Gas Controls Systems Step The Gas Supply LineFigure 30. Gas Supply Line Step Gas Pressure RequirementsPressure Natural GasFor Standing Pilot Ignition Wiring Wiring theStep Optional AccessoriesFigure 32. Fan Wiring Diagram For Direct Spark Ignition DSI WiringOptional Accessories Remote Wall SwitchThe microswitch Step Finishingis found on model 6000ARCH onlyHearth Extensions Step Installing Trim Logs, and Ember MaterialInstalling the Trim Figure 35. Sealant MaterialPlacing the Ember Material Positioning the LogsFigure 38. Placement of the Ember Material Figure 37. Model 6000TR Glass Assembly1.Lift the trim door up and out of the unit 1.Lift the top trim door up and out of the unitLighting the Fireplace Step Before Lighting the Fireplace StepReview safety warnings and cautions Double-checkfor faulty componentsAfter the InstallationStep Heating Control Step 14 Relief Ports Model 6000ARCHMaintaining and Servicing Your Fireplace Fireplace MaintenanceTURN OFF THE GAS BEFORE SERVICING YOUR FIREPLACEFigure 42. Pilot/Ignitor Flame Patterns Figure 41. Burner Flame PatternsStanding Pilot with Robertshaw Controls only Replacement Parts and AccessoriesPART PART DESCRIPTIONPART Standing Pilot with S.I.T. controls onlyPART DESCRIPTION PART NUMBERBoth Standing Pilot and DSI Ignition DSI Ignition OnlyPART PART DESCRIPTIONGLASS SPECIFICATIONS Both Standing Pilot and DSI Ignition Cont6000TR 22” X 34”ACCESSORY AccessoriesPART DESCRIPTION PART NUMBER