Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000XLS, 6000XLT-CDN, 6000TR Any Such Action May Possibly Cause A Fire Hazard

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Download 48 pages 45.62 Kb

Page 6

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

6

The Heat-N-Glo Warranty will be voided by, and Heat-N-Glo disclaims any responsibility for, the following actions:

•Installation of any damaged fireplace or vent system component.

•Modification of the fireplace or direct vent system.

•Installation other than as instructed by Heat-N-Glo.

•Improper positioning of the gas logs or the glass door.

•Installation and/or use of any component part not manufactured and approved by Heat-N-Glo, not withstanding any independent testing laboratory or other party approval of such component part or accessory.

ANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD.

When planning a fireplace installation, it’s necessary to determine:

•Where the unit is to be installed.

•The vent system configuration to be used.

•Gas supply piping.

•Electrical wiring.

•Framing and finishing details.

•Whether optional accessories—devices such as a fan, wall switch, or remote control—are desired.

If the fireplace is to be installed on carpeting or tile, or on any combustible material other than wood flooring, the fireplace should be installed on a metal or wood panel that extends the full width and depth of the fireplace.

NOTE:

6000TR has top and rear collars. 6000XLT-CDN has top collars only. 6000XLS has rear collars only.

Left Side

Front

Right Side

Figure 1. Diagram of the 6000TR, 6000XLT-CDN and 6000XLS

Image 6

Heat & Glo LifeStyle 6000XLS, 6000XLT-CDN, 6000TR, 6000ARCH manual Any Such Action May Possibly Cause A Fire Hazard

Contents

Models 6000TR 6000XLT-CDN6000ARCH 6000XLS Installers GuideHeat-N-Glo SAFETY AND WARNING INFORMATION Owners GuideTHIS UNIT IS NOT FOR USE WITH SOLID FUEL Section 4 Maintenance and Servicing TABLE OF CONTENTSSection 3 Installing the Fireplace Section 5 Replacement PartsApprovals and Codes Installation CodesHigh Altitude Installations Approval ListingsIntroducing the Heat-N-Glo Gas Fireplaces Pre-installPreparationGetting Started IF YOU ARE USING THE REAR SET OF VENT COLLARSANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Clearance Requirements Installing the FireplaceStep Locating the Fireplace Figure 3. Fireplace Dimensions, Locations, andMinimum Clearances from the Vent Pipe to Step Framing the FireplaceFigure 4. Framing Dimensions Combustible MaterialsIdentifying Vent Components Step Installing the Vent SystemA. Vent System Approvals Figure 5. Vent Components and TerminationsDV-48D DV-36D DV-90DDV-45D DV-12DSTRAIGHT UP Figure 7. Straight Up Vertical VentingVERTICAL VENTING V FT 40 MAX. 12.4 M Kit No Figure 8. Corner InstallationHORIZONTAL VENTING Max. RunVENTING WITH ONE 1 90 ELBOW Figure 9. Venting with One 90 ElbowNOTE MODEL 6000ARCH FOR 6000TR & 6000XLT-CDNVENTING WITH ONE 1 90 ELBOW Figure 10. Venting with One 90 ElbowVENTING WITH TWO 2 90 ELBOWS Figure 11. Venting with Two 90 ElbowsH + H1 6000ARCH VENTING WITH TWO 2 90o ELBOWSNOTE MODEL VENTING WITH TWO 2 90o ELBOWSH + H1 + H2 Figure 13. Venting with three 90 elbowsH + H1 VENTING WITH THREE 3 90 ELBOWSNOTE MODEL 6000ARCH VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS Figure 14. Venting with three 90 elbowsVenting Out the Top Vent B. Installing Vent Components For Model 6000TRVenting Out the Rear Vent Figure 15 For Model 6000TR1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components Model DVK-01TRDdoes not need an exterior Figure 19. Installing Support Brackets4. Install Firestops firestop on an exterior combustible wallFigure 20. 12 x 12 Hole and Vent Pipe Figure 22. 11 x 11 Hole and New Framing Members Figure 23. Ceiling Firestop Ceiling SideC. Vent Termination Figure 24. Attic FirestopFigure 25. Round & Trapezoid Termination Caps TERMINATION CAPS Figure 26. Vent Termination Minimum ClearancesIF EXTERIOR WALLS ARE FINISHED WITH =VENT TERMINALMAJOR U.S. BUILDING CODES SPECI THE INTEREST OF SAFETY. SEE THEFOLLOWING DIAGRAM FOR MINIMUM FY MINIMUM CHIMNEY AND/OR VENTRoof Pitch Step The Gas Control Systems Step Positioning Leveling, and Securing theFireplace Figure 28. Proper Positioning, Leveling, andStep The Gas Supply Line Figure 29. Gas Controls SystemsPressure Step Gas Pressure RequirementsFigure 30. Gas Supply Line Natural GasStep Wiring theFor Standing Pilot Ignition Wiring Optional AccessoriesOptional Accessories For Direct Spark Ignition DSI WiringFigure 32. Fan Wiring Diagram Remote Wall Switchis found on model Step FinishingThe microswitch 6000ARCH onlyInstalling the Trim Step Installing Trim Logs, and Ember MaterialHearth Extensions Figure 35. Sealant MaterialPositioning the Logs Placing the Ember Material1.Lift the trim door up and out of the unit Figure 37. Model 6000TR Glass AssemblyFigure 38. Placement of the Ember Material 1.Lift the top trim door up and out of the unitReview safety warnings and cautions Step Before Lighting the Fireplace StepLighting the Fireplace Double-checkfor faulty componentsStep Heating Control InstallationAfter the Step 14 Relief Ports Model 6000ARCHTURN OFF THE GAS BEFORE SERVICING Fireplace MaintenanceMaintaining and Servicing Your Fireplace YOUR FIREPLACEFigure 41. Burner Flame Patterns Figure 42. Pilot/Ignitor Flame PatternsPART Replacement Parts and AccessoriesStanding Pilot with Robertshaw Controls only PART DESCRIPTIONPART DESCRIPTION Standing Pilot with S.I.T. controls onlyPART PART NUMBERPART DSI Ignition OnlyBoth Standing Pilot and DSI Ignition PART DESCRIPTION6000TR Both Standing Pilot and DSI Ignition ContGLASS SPECIFICATIONS 22” X 34”PART DESCRIPTION AccessoriesACCESSORY PART NUMBER