Manuals / Heat & Glo LifeStyle / Household Appliance / Indoor Fireplace

Heat & Glo LifeStyle 6000ARCH Both Standing Pilot and DSI Ignition Cont, Glass Specifications

Models: 6000TR 6000XLT-CDN 6000XLS 6000ARCH

1 48

Page 47

Both Standing Pilot and DSI Ignition (Cont.)

Both Standing Pilot and DSI Ignition (Cont.)
PART	PART DESCRIPTION		PART NUMBER
High Temperature Limit Switch			SRV92–531
Burner NG			SRV446-176A
Burner LP			SRV446-175A
Burner Orifice
6000TR NG Rear Venting (#38DMS)			SRV57-800
6000TR LP Rear Venting (#52DMS)			SRV57-801
6000TR NG Top Venting (#36DMS)			SRV79-831
6000TR LP Top Venting (#51DMS)			SRV79-803
6000ARCH NG (#39DMS)			SRV66-800
6000ARCH LP (#53DMS)			SRV60-801
6000XLS, XLT-CDN NG (#32DMS)			SRV420-800
6000XLS, XLT-CDN LP (#50DMS)			SRV446-801
On/Off Rocker Switch			SRV60–521A
Glass Door Assembly			GLA-6FL
Grate Assembly			SRV446-360A
6000ARCH
6000XLS
6000XLT-CDN
Grate Assembly			SRV60-361A
6000TR
Refractory
6000TR			SRV446-338
6000XLS
6000XLT-CDN
6000ARCH			SRV446-339
Glass Spring Fastener			SRV79-001A
GLASS SPECIFICATIONS:	6000TR:	22” X 34”	TEMPERED
	6000XLS:	22” X 34”	CERAMIC
	6000XLT-CDN:	22” X 34”	CERAMIC	47
	6000ARCH:	22” X 34”	CERAMIC	47
	6000ARCH:	22” X 34”	CERAMIC

Page 47

Image 47

Heat & Glo LifeStyle 6000ARCH Both Standing Pilot and DSI Ignition Cont, Glass Specifications, 6000TR, 22” X 34”, Tempered

Contents

Heat-N-Glo Models 6000TR 6000XLT-CDN6000ARCH 6000XLSInstallers Guide THIS UNIT IS NOT FOR USE WITH SOLID FUEL SAFETY AND WARNING INFORMATIONOwners Guide Section 5 Replacement Parts TABLE OF CONTENTSSection 3 Installing the Fireplace Section 4 Maintenance and ServicingApproval Listings Installation CodesHigh Altitude Installations Approvals and CodesIF YOU ARE USING THE REAR SET OF VENT COLLARS Pre-installPreparationGetting Started Introducing the Heat-N-Glo Gas FireplacesANY SUCH ACTION MAY POSSIBLY CAUSE A FIRE HAZARD Figure 2. Diagram of the 6000ARCH Figure 3. Fireplace Dimensions, Locations, and Installing the FireplaceStep Locating the Fireplace Clearance RequirementsCombustible Materials Step Framing the FireplaceFigure 4. Framing Dimensions Minimum Clearances from the Vent Pipe toFigure 5. Vent Components and Terminations Step Installing the Vent SystemA. Vent System Approvals Identifying Vent ComponentsDV-12D DV-90DDV-45D DV-48D DV-36DVERTICAL VENTING V FT 40 MAX. 12.4 M STRAIGHT UPFigure 7. Straight Up Vertical Venting Max. Run Figure 8. Corner InstallationHORIZONTAL VENTING Kit NoFigure 9. Venting with One 90 Elbow VENTING WITH ONE 1 90 ELBOWFigure 10. Venting with One 90 Elbow FOR 6000TR & 6000XLT-CDNVENTING WITH ONE 1 90 ELBOW NOTE MODEL 6000ARCHH + H1 VENTING WITH TWO 2 90 ELBOWSFigure 11. Venting with Two 90 Elbows VENTING WITH TWO 2 90o ELBOWS VENTING WITH TWO 2 90o ELBOWSNOTE MODEL 6000ARCHVENTING WITH THREE 3 90 ELBOWS Figure 13. Venting with three 90 elbowsH + H1 H + H1 + H2Figure 14. Venting with three 90 elbows VENTING WITH THREE 3 90 ELBOWSVENTING WITH THREE 3 90 ELBOWS NOTE MODEL 6000ARCHFigure 15 For Model 6000TR B. Installing Vent Components For Model 6000TRVenting Out the Rear Vent Venting Out the Top Vent1.Apply the stove ce- ment Figure 2. Continue Adding Vent Components firestop on an exterior combustible wall Figure 19. Installing Support Brackets4. Install Firestops Model DVK-01TRDdoes not need an exteriorFigure 20. 12 x 12 Hole and Vent Pipe Figure 23. Ceiling Firestop Ceiling Side Figure 22. 11 x 11 Hole and New Framing MembersFigure 24. Attic Firestop C. Vent TerminationFigure 25. Round & Trapezoid Termination Caps =VENT TERMINAL Figure 26. Vent Termination Minimum ClearancesIF EXTERIOR WALLS ARE FINISHED WITH TERMINATION CAPSFY MINIMUM CHIMNEY AND/OR VENT THE INTEREST OF SAFETY. SEE THEFOLLOWING DIAGRAM FOR MINIMUM MAJOR U.S. BUILDING CODES SPECIRoof Pitch Figure 28. Proper Positioning, Leveling, and Step Positioning Leveling, and Securing theFireplace Step The Gas Control SystemsFigure 29. Gas Controls Systems Step The Gas Supply LineNatural Gas Step Gas Pressure RequirementsFigure 30. Gas Supply Line PressureOptional Accessories Wiring theFor Standing Pilot Ignition Wiring StepRemote Wall Switch For Direct Spark Ignition DSI WiringFigure 32. Fan Wiring Diagram Optional Accessories6000ARCH only Step FinishingThe microswitch is found on modelFigure 35. Sealant Material Step Installing Trim Logs, and Ember MaterialHearth Extensions Installing the TrimPlacing the Ember Material Positioning the Logs1.Lift the top trim door up and out of the unit Figure 37. Model 6000TR Glass AssemblyFigure 38. Placement of the Ember Material 1.Lift the trim door up and out of the unitDouble-checkfor faulty components Step Before Lighting the Fireplace StepLighting the Fireplace Review safety warnings and cautionsStep 14 Relief Ports Model 6000ARCH InstallationAfter the Step Heating ControlYOUR FIREPLACE Fireplace MaintenanceMaintaining and Servicing Your Fireplace TURN OFF THE GAS BEFORE SERVICINGFigure 42. Pilot/Ignitor Flame Patterns Figure 41. Burner Flame PatternsPART DESCRIPTION Replacement Parts and AccessoriesStanding Pilot with Robertshaw Controls only PARTPART NUMBER Standing Pilot with S.I.T. controls onlyPART PART DESCRIPTIONPART DESCRIPTION DSI Ignition OnlyBoth Standing Pilot and DSI Ignition PART22” X 34” Both Standing Pilot and DSI Ignition ContGLASS SPECIFICATIONS 6000TRPART NUMBER AccessoriesACCESSORY PART DESCRIPTION

Both Standing Pilot and DSI Ignition (Cont.)

GLASS SPECIFICATIONS:

6000TR:

22” X 34”

TEMPERED

6000XLS:

CERAMIC

6000XLT-CDN: