Manuals / Brands / TV and Video / DVR / Honeywell / TV and Video / DVR

Honeywell HRSD4 Setting up the Date and Time, Changing the Date, Note, Down, Start, Cancel, Caution, Date/Time, Date/Time, Figure 3-10Date/Time Setup Screen

1 136

Download 136 pages, 2.77 Mb

Configuration

3.Select Start, and enter the Admin password to start the upgrade.

The system restarts automatically after completing the upgrade. The software starts running after restarting the unit.

Note You cannot upgrade the software during clip copy.

4.Save your changes by highlighting OK and pressing . Select Cancel to exit the screen without saving the changes.

Setting up the Date and Time

Highlight Date/Time in the Main menu and press . The Date/Time setup screen appears.

Figure 3-10 Date/Time Setup Screen

Caution If you set a date and time that is older than some of your recorded images, then any images with dates and times later than the new setting will be deleted.

Changing the Date

1.Highlight the first field beside Date/Time in the Date/Time setup screen and press . The individual sections of the date highlight.

2.Adjust the date using the Up and Down arrows.

3.Press when you have the correct date.

Document 800-00919 Rev F	41
02/08

Contents

Four-ChannelDigital Video Recorder User Guide Page Page Revisions FCC Compliance Statement CE Compliance Explanation of Graphical Symbols WARNING WEEE Compliance WEEE (Waste Electrical and Electronic Equipment) RoHS Contents Page Figures Page Page Page Tables Page About This Document Overview of Contents About Cautions and Warnings Important Safeguards Page Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions Page Typographical Conventions Introduction Features Technical Overview Installation Connecting the Video Source Figure 2-2Video Input Connectors Connecting the Loop Through Video Figure 2-3Video Loop Through Connectors Connecting Audio Connecting the Spot Monitor Connecting the RGB Monitor AI 1 to 4 (Alarm In) GND (Ground) ARI (Alarm Reset In) Alarm Out Connecting to the Network Port Figure 2-10Network Connector Connecting to the RS-232CPort Figure 2-11 RS-232CConnector Factory Reset Connecting the USB Port Figure 2-13USB Connector Connecting the Power Cord Figure 2-14Power Cord Connector WARNING! ROUTE POWER CORDS SO THAT THEY ARE NOT A TRIPPING HAZARD. ENSURE THAT THE POWER CORD WILL NOT BE PINCHED OR ABRADED BY FURNITURE Configuration Front Panel Controls ALARM MENU DVR Front Panel Controls Control Function ZOOM/PTZ Button Zoom PTZ PANIC Button ENTER/PAUSE Button Connecting the Infrared Remote Control Turning on the Power Initial Unit Setup Setting Up Your DVR Using the Quick Setup Screen Figure 3-4Quick Setup Screen Quick Setup Screen Options Option Action If you select A screen opens where you can Changing the System Information Changing the Site Description Changing the Unit ID Changing the Language Setting Upgrading the Software Setting up the Date and Time Changing the Date Changing the Time Changing the Time Zone Turning Daylight Saving Time On and Off Adding Holidays Synchronizing with a Standard Time Server Setting the Date and Time Formats Checking the System Setting Up Alarm Out/Notify Setting Up the DVR for Storage Table 3-4Storage Screen Setup Fields Setting Up for Notification of Storage Problems Setting the Self-Monitoring,Analysis and Reporting Technology (S.M.A.R.T) Figure 3-16S.M.A.R.T. Setup Screen S.M.A.R.T. Setup Screen Options Last-check Period Daily Viewing Events Using the System Log Screen System Shutdown Choosing Camera Input Using the Camera Setup Screen Assigning a Title to a Camera Selecting a PTZ (Pan, Tilt, Zoom) Device Assigning an ID Number to a Camera Setting the Alarm In Settings Setting the Motion Detector Turning Motion Detection On or Off Selecting the Sensitivity Level of the Motion Detector Defining the Motion Detection Area Table Motion Detection Zone Screen Options Setting Up the Text-InFeature Settings for Generic Text, EPSON-POS,and VP Filter Page Text-InSetup Screen Options Virtual Port Transaction Transaction Start Any Character Setting Up the Alarm Output Titling an Alarm Output Scheduling an Alarm Output Setting the DVR to Record Audio Communicating with External Devices Using the RS-232CPort RS232 Figure 3-31RS232 Setup Screen Baud Rate Parity Configuring Recording Settings Using the Record Mode Setup Screen Setting the DVR for Auto Deletion Setting the DVR for Time-LapseRecording Setting Time-LapseRecording Using the Recording Schedule Setting a Schedule for Time-LapseRecording Setting the Speed for Time-LapseRecording Setting the Recording Quality for Time-LapseRecording Turning On the Time-LapseRecording Schedule Setting the Maximum Amount of Time-LapseVideo Storage Setting the DVR for Pre-EventRecording Alarm In Event Action (Record) Setup Screen Alarm In Event Action (Alarm Out) Setup Screen Alarm In Event Action (Notify) Setup Screen Motion Detector Event Action (Record) Setup Screen Motion Detector Event Action (Alarm Out) Setup Screen Motion Detector Event Action (Notify) Setup Screen Text-InEvent Action (Record) Setup Screen Text-InEvent Action (Alarm Out) Setup Screen Text-InEvent Action (Notify) Setup Screen Video Loss Event Action (Record) Setup Screen Video Loss Event Action (Alarm Out) Setup Screen Video Loss Event Action (Notify) Setup Screen Setting Up the OSD (On-ScreenDisplay) Setting Up the Main Monitoring Screen Figure 3-49Main Monitoring Setup Screen OptionFunction Sequence Dwell Event Monitoring Setting Up the DVR Network Connections Network Using the Network Setup Screen for Network Connection Setting the Connection Type Changing Network Passwords Changing the Admin Password Changing a User Password Setting the Transfer Speed Changing the Image Quality for Transfer Setting Up Connectability Using the Network Setup Screen Setting LAN Parameters Manually DNS Server Port Number Setup… Figure 3-52Port Number Setup Screen Setting Up LAN Connectivity Using the Current IP Address Setting Up LAN Connectivity Using ADSL Setting Up the Modem Registering the Network for DVRNS Service Figure 3-56DVRNS Setup Screen Use DVR Name Service DVRNS Server Port Use NAT Setting up the Callback Center Feature Setting Up the Callback Center to Contact a Computer Setting Up the Callback Center to Contact a Pager Figure 3-58Callback Center (Modem) Setup Screen Pager Number Mailbox Site ID Setting Up DVR Passwords Changing the Administrator Password Locking the Buttons on the Front Panel or Remote Control Unlocking the Buttons on the Front Panel or Remote Control Backing Up Video Clips Using Clip Copy Using the DVR While Backing Up Video Page Loading Default Settings Loading and Saving DVR Settings Loading Saved DVR Settings Saving Current DVR Settings Clearing All Data Page Operation Turning On the Power Live Monitoring Full Screen Display Multi-ViewDisplays Monitoring Event-DetectedVideo Overriding the Event-DetectedVideo Setting Displaying Text-InData Figure 4-2Live Monitoring (Text-In)Screen Controlling PTZ Using the Remote Control Setting Camera Preset Positions Using the PTZ Menu Saving a Preset Camera Position Applying a Preset Camera Position Using Digital Zoom Recording Playing Recorded Video Playback Arrow Buttons Using Digital Zoom in Playback Mode Figure 4-7Digital Zoom Screen Figure 4-8Enlarged Digital Zoom Screen Searching Recorded Video Figure 4-10Date/Time Search Screen Calendar Search Calendar Search Figure 4-11Calendar Search Screen Query Search Figure 4-13Event Search (by Event) Screen Search by Search by (Event) Search by (Camera) Text-InSearch Searching with the Text-InLog screen Setting up Search Conditions for a Text-InSearch Load Query Save Query Clear Query Comp Value USB Hard Disk Drive Preparation RUN ENTER 7.In the FDISK Option menu, choose 5. Change current fixed disk drive 9.In the FDISK Option menu, choose 1. Create DOS partition or Logical DOS Drive Text-InQuery Examples Figure B-2 Text-InQuery Example Troubleshooting Page Connector Pinouts Page Map of Screens Page Specifications Connectors Index Page Page Page Page www.honeywellvideo.com +1.800.796.CCTV (North America only) HVSsupport@honeywell.com