![](/images/backgrounds/160496/160496-270263x1.png)
Message | Explanation and/or corrective action | Level |
|
|
|
Registry read failure at re- | The registry has to be read when switching into user mode. This is because the | LOG_ERROR |
enter user mode | administrator can change the settings during administration mode. The read of |
|
| the registry failed which means the Administration key was not found or the Ap- |
|
| pName value was missing or empty. |
|
|
|
|
Registry read failure | The registry read failed. The registry information read when this message is | LOG_ERROR |
| logged is the application information. It the Administration key cannot be opened |
|
| or if the AppName value is missing or empty, this error is logged. The other ap- |
|
| plication information is not required. If the AppName value is not available, Ap- |
|
| pLock cannot switch into user mode. |
|
|
|
|
Reset system work area | The system work area is adjusted when in user mode to cover the taskbar area. | LOG_ERROR |
failure | The system work area has to be adjusted to exclude the taskbar area in admin- |
|
| istration mode. AppLock was unable to adjust this area. |
|
|
|
|
Shift pressed | The Shift key has been pressed and trapped by the HotKey processing. | LOG_EX |
|
|
|
Shift | Processing the hotkey and backdoor entry | LOG_EX |
|
|
|
Show taskbar | The taskbar is now being made visible and enabled. | LOG_ |
|
| PROCESSING |
|
|
|
Switching to | The system is currently in user mode and is now switching to admin mode. The | LOG_ |
door | switch occurred because of the backdoor key presses were entered by the ad- | PROCESSING |
| ministrator. |
|
|
|
|
Switching to | The system is currently in user mode and is now switching to admin mode. The | LOG_ |
press | switch occurred because of a hotkey press by the administrator. | PROCESSING |
|
|
|
Switching to | The keyboard hook load failed, so AppLock switches to admin mode. If a pass- | LOG_ |
hook.dll not found | word is specified, the password prompt is displayed and remains until a valid | PROCESSING |
| password is entered. |
|
|
|
|
Switching to | If the keyboard hook initialization fails, AppLock switches to admin mode. If a | LOG_ |
board hook initialization | password is specified, the password prompt is displayed and remains until a val- | PROCESSING |
failure | id password is entered. |
|
|
|
|
Switching to | See the explanation of the “Registry read failure” above. AppLock is switching | LOG_ |
read failure | into Admin mode. If a password has been configured, the prompt will be dis- | PROCESSING |
| played and will not be dismissed until a valid password is entered. |
|
|
|
|
Switching to Taskbar- | In administration mode, the taskbar is visible and enabled. | LOG_EX |
ScreenMode |
|
|
|
|
|
Switching to user mode | The registry was successfully read and AppLock is starting the process to switch | LOG_ |
| to user mode. | PROCESSING |
|
|
|
Switching to | The system is currently in admin mode and is now switching to user mode. The | LOG_ |
press | switch occurred because of a hotkey press by the administrator. | PROCESSING |
|
|
|
Taskbar hook failure | AppLock is unable to control the taskbar to prevent the locked application from | LOG_ERROR |
|
| |
|
|
|
Taskbar hook OK | AppLock successfully installed control of the taskbar. | LOG_EX |
|
|
|
Timeout looking for app | After the application is launched, AppLock must wait until the application has ini- | LOG_ERROR |
window | tialized itself before proceeding. The application did not start successfully and |
|
| AppLock has timed out. |
|
|
|
|
ToUser after admin, not at | The user mode switch is attempted when the device boots and after the admin- | LOG_EX |
boot | istrator presses the hotkey. The mode switch is being attempted after a hotkey |
|
| press. |
|
|
|
|
ToUser after | The switch to user mode is being made via a hotkey press and the administrator | LOG_EX |
still open | has left the application open and has not made any changes in the configuration. |
|
|
|
|
ToUser after | If user mode is being entered via a hotkey press, the administrator may have left | LOG_EX |
or cmd line change | the configured application open. If so, AppLock does not launch the application |
|
| again unless a new application or command line has been specified; otherwise, |
|
| it just locks it. |
|
|
|
|
Unable to move desktop | The desktop is moved when switching into user mode. This prevents them from | LOG_ERROR |
| being visible if the application is exited and restarted by the timer. This error |
|
| does not affect the screen mode switch; processing continues. |
|
|
|
|
10 - 11