To adjust the bias adjust screw | IBM EasyCoder 3400e guide

EasyCoder 3400e Bar Code Label Printer User’s Manual

To adjust the bias adjust screw

1. Remove the media cover and locate the bias adjust screw.

Bias adjust screw

Power
Alert
E
mpty/
		Pause
Feed	/Pa
		use
I
nter
	mec
	3400

3XXXU.038

2.To compensate for uneven print quality, turn the bias adjust screw as shown. Adjusting the bias adjust screw causes the printhead to rest evenly on the drive

roller and results in even print quality.

If printing is light on the right side of label, turn the

bias adjust screw counterclockwise.

If printing is light on

the left side of label, turn

the bias adjust screw clockwise.

A R E

E R A

3XXXU.039

3. Replace the media cover.

5-4

Image 74

Contents

EasyCoder 3400e Bar Code Label Printer Page Contents Inspecting the Printer Tools for Cleaning the Printer Optimizing and Maintaining Print Quality Using Test and Service Mode Procedures Printer Specifications A-3 Communication Protocols C-3 Bar Code Symbologies Supported A-8Extended Character Sets B-6 Printer Serial Port C-11 Full Ascii Table D-3 Full Ascii Control Characters Table D-5 ViiPage Before You Begin Warranty InformationSafety Summary EasyCoder 3400e Bar Code Label Printer User’s Manual Avertissement For Information On Refer To About This ManualWhat You Will Find in This Manual Conventions Terms and ConventionsTerms Convention Description Other Intermec Manuals XiiiPage Getting Started Page Getting to Know Your Printer Back View LED To plug in the printer Preparing the Printer for InstallationPlugging In the Printer Opening the Printer To open the printer Loading Media for Fanfold Printing To load media for fanfold printing Head lift lever Hardware Configuration Test Label Printing the Hardware Configuration Test LabelTo print the hardware configuration test label If a Hardware Configuration Test Label Does Not Print Connecting the Printer to Your SystemWhat the Hardware Configuration Test Label Tells You Use Intermec Cable Part Number Connecting Your Printer to a PCConnecting the Printer to a PC Serial Port To connect your printer to a PC serial port To connect your printer to a PC parallel port Connecting Your Printer to a NetworkConnecting the Printer to a PC Parallel Port Connecting the Printer to an AS/400 Connecting Your Printer to a Network Connecting the Printer to a Mainframe Cabling in Noisy Electrical Environments DIP Switch Setting Descriptions Configuring the Serial Port for CommunicationsTo configure the printer serial port Parameter Description Bottom Bank Switch Number Verifying Printer Communications With Your System To verify communications with your system At the DOS prompt, type this command and press Enter Operating the Printer Page Learning How to Operate the Printer Understanding the Front Panel Understanding the Front Panel LEDs LED Using the Feed/Pause Button Printer Mode You Want To What to Do To load the media Loading Media Into the PrinterLoading Roll Media for Straight-Through Printing Loading Roll Media for Straight-Through Printing Loading Media for Self-Strip Printing To load self-strip media Loading Media for Self-Strip Printing Loading Thermal Transfer Ribbon To load thermal transfer ribbon Loading Thermal Transfer Ribbon Setting the Media Sensitivity Number Sensitivity Media or Ribbon Number Description Setting the MSN for Intermec Media and RibbonTo print a software configuration label Approximate Sensitivity Maximum Setting the MSN for Other Media and Ribbon3400e Printer Direct Thermal Media Sensitivity Settings Numbers Setting Direct Thermal Media Print Speed Using Intermec Printer Language IPL Commands Using the PrintSet SoftwareUsing Third-Party Software Communicating With the Printer Printing a Test Label To print the test labelPage Maintaining the Printer Page Tools for Cleaning the Printer Inspecting the Printer Maintenance Schedule Printer Component Maintenance Period Locating the Printer Parts You Need to Maintain Cleaning the Printhead To clean the printhead Cleaning the Printer Covers Cleaning the Printhead Cleaning the Drive Roller and Tear Bar To clean the drive roller and tear bar Cleaning the Media Guides and Media Path To clean the media guides and media path Cleaning the Label Sensors To clean the label sensors Cleaning the Label Sensors Page Troubleshooting Page Troubleshooting Troubleshooting ChecklistPrinter Operation Problems Symptom Possible Causes Solution Symptom Possible Causes Solution Print Quality ProblemsTroubleshooting Printer Operation Problems Symptom Possible Causes Communication Problems and Preventing Data Loss Troubleshooting Print Quality Problems To check for communication problems Optimizing Printer Performance Page Optimizing and Maintaining Print Quality Correcting Uneven Print Quality To adjust the bias adjust screw Adjusting the Print Darkness To adjust the print darkness Adjusting the Label Mark Sensor To adjust the label mark sensor Platen roller Making the Most of Your Memory Using the Printer Memory EfficientlyHow Is the Printer Storage Memory Used? Increasing Throughput What Is an Image Band?How the Image Bands Command Works Optimizing Print Speed and Image Band Setting To optimize the number of image bands for your print speed Using Test and Service Mode Page To exit Test and Service mode Using Test and Service Mode ProceduresTo enter Test and Service mode Test and Service DIP Switch Settings Tests Printing Test Labels Using Data Line PrintTo enter Data Line Print mode To print a test label To use memory reset Setting Configuration Commands in Test and Service ModeResetting the Memory on Your Printer Setting the Number of Dot Increments Configuration DIP Switch Settings Bottom Bank Adjusting the Label Rest Point To set the number of dot increments To adjust the label rest point Top Bank Setting Description Setting Emulation ModeTo set the printer to Emulation mode using DIP switches Using Forms Adjust Format Forms Adjust To set the X forms adjust To set the Y forms adjust Specifications Page Printer Specifications Specifications Ribbon Printhead 200 dpiPrinthead 400 dpi Printing Speed Media Number Description Minimum Maximum Finishers Printer OptionsCommunication Interface Specifications Signal Pin Return Direction Description Bar Code Symbologies Supported Hibc 2D Matrix Symbologies 2D Symbologies2D Stacked Symbologies EasyCoder 3400e Bar Code Label Printer User’s Manual Character Sets Page International Character Sets Advanced Character Table Emulation Mode Character Table IBM Translation Character Table Code Page 850 Character Table Extended Character Sets 10 x 14 Standard Monospace fonts 6 point to 36 point OCR a Characters in Font C24 Page Communications Reference Page Printer Status Character Communication ProtocolsIntermec Standard Protocol XON/XOFF Protocol Software and Hardware Flow Control Multi-Drop Protocol Polling Mode DXON/XOFF, No Status Protocol User-Defined Protocol Character Protocol Affected Communications Boundaries Communications InterfacesHost Requirements RS-232 Serial Interface Interface Pin No Name Operation RS-422 Serial InterfaceRS-485 Serial Interface RS-232 Null Modem Cable for PC/XT Part Number RS-232 Null Modem Cable for PC/AT Part Number RS-422 Intermec Pin Assignments PIN Plug D-SUB Metal Backshell Printer Serial Port Page Full Ascii Table Page Binary0 Hex1 Dec2 C393 Full Ascii TableFull Ascii Table Binary0 Hex1 Dec2 C393 Full Ascii Control Characters Table Control Character DefinitionPage Glossary Page Glossary G ConfigurationData Line Print mode Backing Feed/Pause Emulation modeDirect thermal Field Imaging Glossary G GraphicHuman-readable Image bands Ips Mnemonic code EasyCoder 3400e Bar Code Label Printer User’s Manual MarginMedia Multi-Drop protocol Print speed Polling Mode D protocolGlossary G Point size Printhead Selective transfer SymbologyEasyCoder 3400e Bar Code Label Printer User’s Manual Scan Self-strip Variable data field User-Defined Characters UDCUser-Defined Fonts UDF XON/XOFF protocolPage Index Page Numbers Index EasyCoder 3400e Bar Code Label Printer User’s Manual LED RAM XON/XOFF