Integra DTR-6.2 instruction manual Connections

Connections

Here is explanation of how to connect the main components to the DTR-6.2 in the standard manner. There are many ways that any one component can be connected, and it is up to you to decide which method best fits your situation. The directions given here are only one option and should only be thought of as such. It is best to fully understand the nature of each connector and terminal as well as each of your components and their features to ascertain which method of connection is best.

•Be sure to always refer to the instructions that came with the component that you are connecting.

•Insert all plugs and connectors securely. Improper connections can result in noise, poor performance, or damage to the equipment.

Improper connection

Inserted completely

•Do not plug in the power cord until all connections have been made.

•For input jacks, red connectors (marked R) are used for the right channel, white connectors (marked L) are used for the left channel, and yellow connectors (marked V) are used for video connection.

•Do not bind audio/video connection cables with power cords and speaker cables. Doing so may adversely affect the picture and sound quality.

•When using the digital inputs, make sure to also connect the analog connections whenever possible.

Connecting antennas [22, 23]
Connect to devices with z	Connecting your video
terminals [16]	components [14, 15]

•When using one of the optical input jacks, remove the protective cap and keep it safely. When the jack is not used, replace the protective cap.

•When using an optical input jack, always use an optical fiber cable.

Optical digital input terminal

An optical digital input terminal is equipped with a protection cap. When connecting, remove this cap. When not using, put the cap back on the terminal.

Cautions regarding the AC

OUTLETS connectors [16]

12V TRIGGER A, B terminals

[17]

Connecting speakers [17-19]

ANTENNA

12 V

COMPONENT VIDEO

TRIGGER

Y

PB

PR

Y

PB

PR

Y

PB

PR

AM

A

OUTPUT

INPUT 1

INPUT 2

IN

OUT

IN

OUT

IN

IN

IN

VIDEO

B

FM

MONITOR

DVD

VIDEO 1

VIDEO 2

VIDEO 3 VIDEO 4

75

REMOTE

OUT

CONTROL

S VIDEO

PHONO

CD

TAPE

ZONE 2

OUT

IN

PRE OUT

L

L

R

R

FRONT

SURR

CENTER

OPTICAL

COAXIAL

IR

L

1

2

IN

GND

1

RS 232

2

OUT

R

SUB

SUBWOOFER

MULTI

WOOFER

PRE OUT

CHANNEL INPUT

DIGITAL INPUT

FRONTCENTER

SPEAKERSSPEAKER

RL

AV RECEIVER

MODEL NO. DTR-6.2

PRE OUT

FRONT SURR CENTER

L	1
R	2

SURROUND

SPEAKERS

RL

	ZONE 2
	SPEAKERS
R	L
CAUTION:		AC INLET
SEE INSTRUCTION MANUAL
FOR CORRECT SETTING.
6 OHMS	4 OHMS
MIN.	MIN.
/ SPEAKER	/ SPEAKER

SET BEFORE POWER ON

IMPEDANCE SELECTOR

AC OUTLETS

AC 120V 60 Hz

SWITCHED

TOTAL 120W 1 A MAX.

Connecting a subwoofer [18]

RS232 port [17]

Connecting power amplifiers [16]

Plugging in the power cord to the AC INLET receptacle [17]

Connecting your audio components [13]

Connect to devices with	Operating components	Connecting the remote
multichannel output [17]	not reached by the remote	zone speakers [19]
	controller signals [20]
	Default setting

Input source	Digital input	Component video	Multichannel
DVD	COAX 1	INPUT 1	Yes
Video 1	COAX 2	INPUT 2	No
Video 2	----	INPUT 1	No
Video 3	OPT 2	INPUT 1	No
Video 4	----	INPUT 1	No
Tape	----		No
FM
AM
Phono	----		No
CD	OPT 1		No

COAX: Coaxial OPT: Optical ----: No setting : Not applicable

12