Integra DTR-6.2 Volume Setup sub-menu Description listening mode parameters, Front Effect

Setup menus

3. Listening Mode Setup menu 4. Preference menu

This menu allows you to make adjustments to the various listening modes. These adjustments are in the form of parameters and each one is explained below. Note that some parameters cannot be set for some listening modes and that no sub-menu will have all parameters. Also, for some input signal formats, changes in the listening mode parameters may actually result in no change to the resulting output signal.

Menu

1.Speaker Setup

3.Listening Mode Setup

2.Input Setup

3.Listening Mode Setup

4.Preference

1.Stereo Setup

5.OSD Setup

2.Surround Setup

3.Orchestra Setup

4.Unplugged Setup

5.Studio-Mix Setup

6.TV Logic Setup

ENTER Quit:OSD

7.All Ch Stereo Setup

ENTERQuit:SETUP

Menu

1.Speaker Setup 4.Preference 2.Input Setup

3.Listening Mode Setup

4.Preference 1.Volume Setup

5.OSD Setup 2.Headphones Level

3.LateDTSLFENightLevelSetupSetup 4.4IRAM.PowereddFrequencyIN setupZone2Setup 5.Powered Zone2 Setup

ENTER Quit:OSD

ENTERQuit:SETUPQuit:OSD

4-1. Volume Setup sub-menu

Description listening mode parameters

Menu

1.Speaker Setup

3.Listening Mode Setup

2.Input Setup

3.Listening Mode Setup

4.Preference

31-.1Ster.ereoSetupSetup

5.OSD Setup

2.Theater-Dimensional

Setup

3a..SurroundSubwooferSetup: On

4.THX Setup

5.Mono Movie Setup

ENTER Quit:OSD

ENTER Quit:OSD

Quit:SETUP

Menu

1.Speaker Setup 4.Preference 2.Input Setup

3.Listening Mode Setup

4.Preference 41-.1Volume.SetupSetup

5.OSD Setup 2.Headphones Level

3.DTS LFE Level Setup 4a..PoweredMaximumZone2VolumeSetup

:Off

b.Power on Volume ENTER Quit:OSD

:Last

ENTER Quit:OSD

Quit:SETUP

This sub-menu allows you to make various settings concerning the volume control of the DTR-6.2.

Subwoofer

Set this to “Off” if you are not using a subwoofer (even if one is connected). If “No” is selected for the Subwoofer setting in the Speaker Config sub-menu, then this setting will not appear.

Front Effect

You can choose from “Low,” “Middle,” or “High.”

Some live recordings contain acoustic reverberation. When you play these sources, more reverberation will be applied by the DSP, creating too much reverb effects and the sound loses frame or presence. In this case, set this setting to “Low.” No reverberation from the DSP will be applied to the sound output from the three front channels, so the sound source is be played as it is without any further reverberation.

Surround Effect

You can choose from “Low,” “Middle,” or “High.”

This adjusts the reflected and residual noises from the surround left and right speakers.

Relationship between listening mode and parameter

a. Maximum Volume

This setting allows you to set the maximum volume that can be output with the Master Volume dial to prevent components from being damaged by excessively loud volumes. The maximum volume can be set between 30 and 79.

b. Power On Volume

This sets a designated volume setting for the DTR-6.2 to be set every time that the power is turned on. This prevents the DTR-6.2 from being turned on while it is set to an extremely high volume and suddenly output very loud sounds. The power on volume can be set between min and max. If you do not mind having the DTR-6.2 turned on with its current volume setting, set this to “Last.”

Listening mode	Direct	Stereo	Surround	Orchestra	All Ch
			Dolby Pro Logic II	Unplugged	Stereo
			Dolby Digital	Studio-Mix
Parameter			DTS	TV Logic
Subwoofer		Off, On	Off, On	Off, On	Off, On
Front Effect				Low, Mid, High
Surround Effect				Low, Mid, High

The parameters that can be set are different for each listening mode.

41